| Maintenance indicator | Problem | Cause | Possible solution | |||||
|
|
|
|
|
| ||||
|
|
| Normal | Abnormal | |||||
|
|
|
|
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| • Relocate the projector to an area | |
|
|
|
|
|
|
| • Blocked air intake | with proper ventilation (see page | |
| Temperature |
|
|
| Red on | The internal |
| 7). |
|
|
|
|
|
|
|
| |||
|
|
|
|
| • Take the projector to your nearest | ||||
| warning |
| Off | temperature is | • Cooling fan break- | ||||
|
| (Standby) | |||||||
| indicator |
|
|
| abnormally high. | EIKI Authorized Projector Dealer | |||
|
|
|
| down | |||||
|
|
|
|
|
|
| or Service Center for repair. | ||
|
|
|
|
|
|
| • Internal circuit failure | ||
|
|
|
|
|
|
| • Clean the exhaust and intake | ||
|
|
|
|
|
|
| • Clogged air intake | vents. (See page 63.) | |
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| The lamp does | • The lamp is shut | • Disconnect the power cord from | |
|
|
|
|
|
| the AC outlet, and then connect it | |||
|
|
| Green on |
| not illuminate. | down abnormally. | |||
|
|
|
| again. | |||||
|
|
|
|
|
| ||||
|
|
| Green blinks |
| Red on |
|
|
|
|
|
|
|
|
|
| • Carefully replace the lamp. (See | |||
| Lamp |
| when the lamp |
| Time to change | • Remaining lamp life | |||
|
|
|
| page 67.) | |||||
|
| is warming up |
|
| |||||
| indicator |
|
|
| the lamp. | becomes 5% or less. | • Take the projector to your nearest | ||
|
| or shutting |
|
| |||||
|
|
|
|
|
|
| EIKI Authorized Projector Dealer | ||
|
|
| down. |
|
|
|
| ||
|
|
|
| Red on | The lamp does | • | or Service Center for repair. | ||
|
|
|
|
| |||||
|
|
|
|
| • Please exercise care when | ||||
|
|
|
|
| (Standby) | not illuminate. | • Lamp circuit failure | ||
|
|
|
|
| replacing the lamp. | ||||
|
|
|
|
|
|
|
| ||
|
|
|
|
|
|
|
|
|
|
Info
•If the temperature warning indicator illuminates and the projector enters the standby mode, check whether any of the ventilation holes are blocked (see page 7) and then try turning the power back on. Wait until the projector has cooled down completely before plugging in the power cord and turning the power back on. (At least 10 minutes.)
•If the power is turned off for a brief moment due to power outage or some other cause while using the projector, and the power supply recovers immediately after that, the lamp indicator will illuminate in red and the lamp may not be lit. In this case, unplug the power cord from the AC outlet, replace the power cord in the AC outlet and then turn the power on again.
•Do not unplug the power cord after the projector has entered the standby mode and while the cooling fan is running. The cooling fan runs for about 90 seconds.
65