Eiki EIP-3500 owner manual Product Disposal

Page 6

WARNING:

The cooling fan in this projector continues to run for about 90 seconds after the projector enters the standby mode. During normal operation, when putting the projector into standby mode always use the POWER button on the projector or on the remote control. Ensure the cooling fan has stopped before disconnecting the power cord.

DURING NORMAL OPERATION, NEVER TURN THE PROJECTOR OFF BY DISCONNECTING THE POWER CORD. FAILURE TO OBSERVE THIS WILL RESULT IN PREMATURE LAMP FAILURE.

PRODUCT DISPOSAL

This projector utilizes tin-lead solder, and a pressurized lamp containing a small amount of mercury. Disposal of these materials may be regulated due to environmental considerations. For disposal or recycling information, please contact your local authorities or, if you are located in the United States of America, the Electronic Industries Alliance: www.eiae.org .

Caution Concerning Lamp Replacement

See “Replacing the Lamp” on page 66.

LAMP REPLACEMENT WARNING :

TURN OFF THE LAMP AND DISCONNECT

POWER CORD BEFORE OPENING THIS

COVER. HOT SURFACE INSIDE.

ALLOW 1 HOUR TO COOL BEFORE REPLACING THE LAMP.

REPLACE WITH SAME EIKI LAMP UNIT MODEL

AH-35001 ONLY.

HIGH PRESSURE LAMP : RISK OF EXPLOSION.

POTENTIAL HAZARD OF GLASS PARTICLES IF LAMP HAS

RUPTURED. HANDLE WITH CARE. SEE OPERATION MANUAL.

SERVICEMAN-WARNING : USE RADIATION EYE AND

SKIN PROTECTION DURING SERVICING.

AVERTISSEMENT CONCERNANT LE

REMPLACEMENT DE LA LAMPE :

ETEINDRE LA LAMPE ET DEBRANCHER LE CORDON

D’ALIMENTATION AVANT D’OUVRIR LE COUVERCLE.

L’INTERIEUR DU BOITIER ETANT EXTREMEMENT CHAUD,

ATTENDRE 1 HEURE AVANT DE PROCEDER AU

REMPLACEMENT DE LA LAMPE. NE REMPLACER QUE

PAR UNE LAMPE EIKI DE MODÈLE AH-35001.

LAMPE A HAUTE PRESSION : RISQUE

D’EXPLOSION. DANGER POTENTIEL DE PARTICULES DE

VERRE EN CAS D’ECLATEMENT DE LA LAMPE.

A MANIPULER AVEC PRECAUTION.

SE REPORTER AU MODE D’EMPLOI.

AVERTISSEMENT – REPARATEUR : SE PROTEGER LES

YEUX ET LA PEAU DES RADIATIONS LORS DES REPARATIONS.

This EIKI projector uses a DMD panel. This very sophisticated panel contains 786,432 pixels micromirrors. As with any high technology electronic equipment such as large screen TVs, video systems and video cameras, there are certain acceptable tolerances that the equipment must conform to.

This unit has some inactive pixels within acceptable tolerances which may result in inactive dots on the picture screen. This will not affect the picture quality or the life expectancy of the unit.

DLPTM (Digital Light Processing) and DMDTM (Digital Micromirror Device) are trademarks of Texas Instru- ments, Inc.

Microsoft® and Windows® are registered trademarks of Microsoft Corporation in the United States and/or other countries.

PC/AT is a registered trademark of International Business Machines Corporation in the United States.

Adobe® Reader® is a trademark of Adobe Systems Incorporated.

Macintosh® is a registered trademark of Apple Computer, Inc. in the United States and/or other countries.

All other company or product names are trademarks or registered trademarks of their respective compa- nies.

Some IC chips in this product include confidential and/or trade secret property belonging to Texas Instru- ments. Therefore you may not copy, modify, adapt, translate, distribute, reverse engineer, reverse as- semble or discompile the contents thereof.

2

Image 6
Contents EIP-3500 Model No. EIP-3500 Serial No Special Note for Users in the U.K Page Introduction Product Disposal Buttons used in this OperationContents Reference Important Safeguards Rest your eyes occasionally Avoid locations with extremes of tem- peratureDo not block the intake and exhaust vents Using the projector in other countries Temperature monitor functionOther connected equipment Setup Guide Accessories Supplied accessoriesOptional accessory Part Names and Functions ProjectorAbout the Indicators on the Projector Lamp indicatorProjector Rear View TerminalsRemote Control CLICK/ENTER button 24·40Inserting the Batteries Using the Remote ControlUsable Range Insert the batteriesSetup and Projection Quick StartAdjust the angle Close the cover of the storage CasePocket of the storage case Setting up the Projector Setting up the ProjectorProjecting a Reversed Image Projection from behind the ScreenConnections INPUT/OUTPUT Terminals and Connectable Main EquipmentSamples of Cables for Connection Audio InputConnecting to a Computer Supplied AccessoriesUsing the Remote Control as the Wireless Computer Mouse Connecting to Video Equipment Supplied AccessoryWhen connecting video equipment with video output terminal When connecting video equipment with S-video output terminalWhen connecting to the LAN terminal using a LAN cable Controlling the Projector by a ComputerConnecting to a Monitor with RGB Input Terminal Connecting to an Amplifier or Other Audio EquipmentTurning the Projector On/Off Connecting the Power CordTurning the Power off Putting Turning the Projector onRear adjustment feet Using the Adjustment FeetHeight Adjust button Image ProjectionKeystone button Correcting Trapezoidal DistortionPress Undo buttonPress on the projector or on the remote control Adjusting the FocusAdjusting the Projected Image Size Focus buttons Zoom buttons Auto Focus buttonVolume buttons Switching the Input ModeAdjusting the Volume Input buttonsDisplaying an Enlarged Portion of an Image Press on the remote controlPress on the remote control to cancel the operation AV Mute buttonFreeze button Undo button Picture Mode button Iris button Selecting the Picture ModeSwitching the High Brightness/High Contrast Mode Freezing a Moving ImageButton //\ Resize ModeMOUSE/Adjustment Undo button Resize buttonVideo When using the Input 1 or Input 2 mode Menu ItemsFollowing shows the items that can be set in the projector Options1 menu Example Adjusting Bright Using the Menu ScreenMenu Selections Adjustments Example Picture screen menu for Input 1 RGB mode Menu iconsPress \ or to adjust the item selected To adjust the pro- jected image while viewing itPress or to select the item you want to adjust Single adjustment itemsMenu Selections Settings Example Setting Menu PositionSub menu Picture Adjustment Picture menu Adjusting the ImageAdjusting the Color Temperature Emphasizing the ContrastExample Picture screen menu for IN- PUT 1 RGB mode SRGB SettingSwitching the High Bright- ness/High Contrast Mode Description of Iris SettingsSignal Type Setting RGBSpecial Modes Setting Computer Image Adjustment Fine Sync menuAdjusting the Computer Image Example Fine Sync screen menu for Input 1 RGB modeAuto Sync Adjustment Checking the Input SignalUsing the Options1 Menu Setting the Resize ModeChecking the Lamp Life Status Setting On-screen Display Setting the Video SystemEco Mode Selecting a Startup and Background ImageAuto Power Off Function Selecting the Menu Screen PositionSystem Lock Function Example Options1 screen menu for Input 1 RGB modeWhen the System Lock is set Select System Lock on the Op Tions1 menu, then pressChanging the keycode When System Lock is set Setting a Password If You Forget Your PasswordExample Options2 screen menu Example Options2 screen menu Description of Auto Focus Auto Focus SettingAuto Keystone Setting Example Options2 screen menu Description of Auto KeystoneSpeaker Setting Setting the Audio Output TypeExample Options2 screen menu Description of PRJ Modes Reversing/Inverting Pro- jected ImagesSelecting the Transmis- sion Speed RS-232C Example Options2 screen menu Description of RS-232CExample Options2 screen menu Description of Monitor Out Monitor Output SettingsLAN/RS232C Setting Description of LAN/RS232CConfirming the Network In- formation for the Projector Press \ or to select the Lan- guage menu icon Using the Language MenuSelecting the On-screen Display Language Press or to select the desired Language, and then pressCleaning the lens MaintenanceCleaning the projector Cleaning the exhaust and intake ventsMaintenance Indicators About the temperature warning indicatorAbout the lamp indicator Abnormal Regarding the Lamp Removing and Installing the Lamp Unit Disconnect the power cordRemove the lamp unit cover Resetting the Lamp Timer Computer Compatibility Chart ComputerTroubleshooting Remote control batteries have run outInput 2 RGB Specifications NTSC3.58/NTSC4.43/PAL/PAL-M/PAL-N/PAL-60/SECAMGlossary Index 32,57Deutschland & Österreich CanadaEastern Europe Japan & Worldwide