Bosch Appliances DVR1EP08 Configuring On-screen Display Options, Main Menu Display Settings

Page 17

4.6Configuring On-screen Display Options

Main Menu Display Settings

Use this menu to specify the status information to be displayed on the primary monitor (usually shown in the upper right or upper left corner of the screen).

Each of the following parameters may be set ON or OFF for the on-screen display:

Current time and date.

Remaining amount of time before the hard disk runs out of record capacity (automatically counts down from days/hours to hours/minutes to minutes/seconds).

CURRENT TIME / DATE

RECORD CAPACITY

ARCHIVE STATUS

LAST ALARM

RECORD/PLAYBACK SPEED

PLAYBACK TIME / DATE

NOTE: Record capacity will only display if: The unit is recording and

The hard disk overwrite mode is set to no overwrite or overwrite once mode (see Section 5.3).

NOTE: Turning this parameter ON will also show the record capacity on the front panel LCD display, replacing the date field.

Status of a system archive device connected (i.e. ready/not ready for recording).

Time and date of the last alarm. Note that the system displays NONE if no previous record(s) of alarm(s) exist.

Record and Playback Speed are displayed

During Playback, the time/date in which the recording was made.

4.7Managing Archive Storage

NOTE: For more information regarding archiving, refer to the Archiving.

Due to the complexity of the Archive Setup process, detailed instructions follow.

Main Menu Archive Setup

Use this menu to accomplish the following:

Select data to be archived and begin the archiving process.

Restore data from the archive device.

Turn Background Archiving On or Off.

Set Archive Overwrite mode.

Erase Disk Array.

Main Menu Archive Setup Selective Archive

SELECTIVE ARCHIVE

RESTORE FROM ARCHIVE

BACKGROUND ARCHIVE

ARCHIVE OVERWRITE MODE

ERASE ARCHIVE MEDIUM

The Selective Archive feature allows archiving of recorded data from the hard disk of the DVR1 to an archive device. If the archive device is a CD-writer, you must play back the archived video from a PC’s CD-ROM drive using the Remote Viewer software (included with the DVR1 package).

The Archive Search Filters Menu allows you to search the hard disk for recorded events (e.g., an alarm condition or a previous recording session), then select those events to be archived for later viewing (note that each activation of Record mode is considered to be a separate recording session).

Use this sub-menu to specify:

Start and stop date of the search.

Start and stop time of the search.

Which camera(s) to search.

A search for recorded alarms.

NOTE: The default settings for Selective Archive are set to show a list of all of the files that are on the hard drive. It may be necessary to limit the size of an archive file so that it will fit on the archive medium. The file size for archiving (time span) can be customized by designating start/stop time and date within the archive search filters window. File size can be further reduced by specifying only the cameras of interest.

ARCHIVE SEARCH FILTERS

 

START

 

 

 

 

STOP

 

DATE: 12/25/00

[ ]

01/01/01

[ ]

(MM/DD/YY)

 

 

(MM/DD/YY)

 

 

 

 

 

 

 

 

 

START

 

 

 

 

STOP

 

TIME: 11:11:21

[ ]

12:34:34

[ ]

 

 

 

 

 

 

 

 

 

 

 

1

2

3

4

5

6

7

8

 

 

 

CAMERA: [ ][ ][ ][ ][ ][ ][ ][ ]

 

 

 

 

 

 

 

 

ALARM: [ ]

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

[CANCEL]

 

 

 

 

 

 

 

[START SEARCH]

 

17

Image 17
Contents DVR1 Series Important Safeguards Safety Precautions Sicherheitshinweise Zasady Bezpieczeństwa Table of Contents Service and Returns Page Guide to This Manual Introduction to DVR1 Series Digital Video RecordersUnpacking Understanding the DVR1 SeriesMounting Installing the DVR1Connecting the DVR1 DB-9 Connector on High 12 DVR1 Front Panel Display Guide to the DVR1 ControlsDVR1 Front Panel Controls Date Format Setup Select Format Main Menu Record Settings Normal Record SpeedNavigating with the DVR1 Controls Not highlightedConfiguring Alarms Setting the Time/DateDVR1 Main Menu Programming Overview of the DVR1 Main MenuMain Menu Timer Settings Configuring Scheduled RecordingsConfiguring the Recording Parameters Main Menu Record SettingsMain Menu Display Settings Configuring On-screen Display OptionsMain Menu Archive Setup Main Menu Archive Setup Selective ArchiveMain Menu Archive Setup Archive Overwrite Mode Main Menu Archive Setup Restore From ArchiveMain Menu Archive Setup Background Archive Accessing the Advanced Menu Main Menu Archive Setup Erase Archive MediumAbout DSR Main Menu About DSRPassword BOX Please Enter the Password DVR1 PasswordsDVR1 Advanced Menu Programming Overview of the DVR1 Advanced MenuUsing the Auto Delete Feature Erasing, Deleting, and Recovering Hard Disk DataOverwriting the Hard Disk Invoking Audio RecordingConfiguring the Multiplexer Format Configuring CommunicationsAdjusting Picture Qualities Locking Out the Front PanelAdvanced Menu Factory Settings Restoring Factory DefaultsChanging the Password Advanced Menu Change PasswordRecording Operating the DVR1 SeriesInitial Startup Message Disk FULL. Recording has Stopped PlaybackSearch Interface Archiving Using CD-WritersArchiving Applications Explained Minimum Write Speed Minimum Read Speed Interface SCSI-2Limitations on CD Operations Creating a CD-ROM with Video FilesMaintenance Service and ReturnsFactory Service All of our products now come with a 3 year warrantyFunction Setting Appendix a Factory Default SettingsGeneral Appendix B Technical SpecificationsConnections AUDIO/VIDEOPart Numbers ON-SCREEN Video IndicatorsIntroduction Required Software Version Appendix C Observation System Quick Install GuideInstallation Programming the DVR1 Programming the Observation System monitorSelect Menu Advanced MENU, then press Enter Remote Viewing ConsiderationsMultiplexer DVR1 OverviewDVR1 Controls DVR1 Keyboard Menus2 DVR1 Playback Controls Menu Setting the Clock Supported Command SequencesCommand Characters Appendix E RS-232 Remote ProtocolSET Clock Example