HCD-PX333
5-1. Operating the Continuous Playback Mode
1. Entering the continuous playback mode
(1)Set the disc in the unit. (Whichever recordable discs or discs for playback only are available)
(2)Press the . “R” or > “R” button to display “CPLAY2MODE” (C36).
(3)Press the ENTER/YES “R” button to change the display to “CPLAY2MID”.
(4)When access completes, the display changes to “C = AD = )”.
Note: The numbers “ ” displayed show you error rates and ADER.
2. Changing the parts to be played back
(1)Press the ENTER/YES “R” button during continuous playback to change the display as below. “CPLAY2MID” t“CPLAY2OUT” t“CPLAY2IN”
When pressed another time, the parts to be played back can be moved.
(2)When access completes, the display changes to “C = AD = )”.
Note: The numbers “ ” displayed show you error rates and ADER.
3. Ending the continuous playback mode
(1)Press the MENU/NO “R” button. The display will change to “CPLAY2MODE” (C36).
(2)Press the Z (MD) button and take out the disc.
Note: The playback start addresses for IN, MID, and OUT are as follows.
IN | : 40h cluster |
MID | : 300h cluster |
OUT | : 700h cluster |
1. Entering the continuous recording mode
(1)Set a recordable disc in the unit.
(2)Press the . “R” or > “R” button to display “CREC 2MODE” (C37).
(3)Press the ENTER/YES “R” button to change the display to “CREC 2MID”.
(4)When access completes, the display changes to “CREC 2( ” and “ REC ” lights up.
Note: The numbers “ ” displayed shows you the recording position addresses.
2. Changing the parts to be recorded
(1)When the ENTER/YES “R” button is pressed during continuous recording, the display changes as below. “CREC 2MID” t“CREC 2OUT” t“CREC 2IN”
When pressed another time, the parts to be recorded can be changed. “ REC ” goes off.
(2)When access completes, the display changes to “CREC 2( ” and “ REC ” lights up.
Note: The numbers “ ” displayed shows you the recording position addresses.
3. Ending the continuous recording mode
(1)Press the MENU/NO “R” button. The display changes to “CREC 2MODE” (C37) and “
(2)Press the Z (MD) button and take out the disc.
REC
”goes off.
Note 1: The recording start addresses for IN, MID, and OUT are as follows.
IN | : 40h cluster |
MID | : 300h cluster |
OUT | : 700h cluster |
Note 2: The MENU/NO “R” button can be used to stop recording anytime.
Note 3: Do not perform continuous recording for long periods of time above 5 minutes.
Note 4: During continuous recording, be careful not to apply vibration.
6. FUNCTIONS OF OTHER BUTTONS
Function | Contents |
N X MD | Sets continuous playback when this is pressed in the STOP state. When this is pressed during continu- |
| ous playback, playback position moves. |
|
|
x (MD) | Stops continuous playback and continuous recording |
|
|
M “R” | The sled moves to the outer circumference only when this is pressed |
|
|
m “R” | The sled moves to the inner circumference only when this is pressed |
|
|
CD SYNC HIGH | Switches between the pit and groove modes when pressed |
|
|
PLAY MODE | Switches the spindle servo mode (CLV S y CLV A) |
CD SYNC HIGH (*1) | Switches the displayed contents each time the button is pressed |
MD Z | Ejects the disc |
|
|
REPEAT STEREO/MONO | Releases the test mode |
|
|
*1) Press the [CD SYNC NORMAL] button to light up “IT” indicator, then press the [CD SYNC HIGH] button.
34