Philips SRU6080 owner manual Setting and Clearing Timers Timer Setup

Page 10

Setup, cont.

Setting and Clearing Timers (TIMER SETUP)

The remote can be programmed with up to 4 Timers (Timer 1, 2, 3 & 4). Each Timer can be assigned up to 4 keys (4 if Macros enabled, 2 if Macros disabled) to activate at the set time. The first key must always be a Mode key. Subsequent keys cannot include Up, Down, Left, Right, OK, Exit, Macro, Setup or any Mode key. Timers can only activate within the following 24-hour period. Timers are automatically cleared after activation. The “Timer Bell” symbol is displayed when any Timer is set.

To set a Timer (Note, the Timer must be cleared first if it was previously set – see To Clear a Timer below)

1.Press and hold the SETUP button until CODE SETUP is displayed (takes about 3 seconds), then release the SETUP button.

2.Press the down navigation button until TIMER SETUP is displayed.

3.Press and release OK. TV SLEEP SETUP is displayed.

4.Press the down navigation button until TIMER X SETUP is displayed (where “X” is 1, 2, 3 or 4). Press and release OK.

5.TIMER X SET is displayed. Press and release OK.

6.TIMER X TIME?” is displayed with the “hours” flashing. Use the Up/Down buttons to set the hours then press and release OK.

7.The “minutes” will be flashing. Use the Up/Down buttons to set the minutes then press and release OK.

8.TIMER X MODE? is displayed. Press and release the desired Mode key (TV, VCR, DVD, etc.).

9.TIMER X Key1? is displayed. Press and release the first key required. If only one key is required, press and release OK at this point – go to Step 12 below. If Macros are disabled, go to Step “l” below.

10.“Timer X Key2? is displayed. Press and release the second key required. If only two keys are required, press and release OK at this point – go to Step 12 below.

11.TIMER X Key3? is displayed. Press and release the third key required.

12.SUCCESS is displayed and the remote remain in Setup Mode, returning to the CODE SETUP screen. Press QUIT then OK to exit Setup Mode.

Setup, cont.

To clear a Timer (“Timer Bell” in normal display)

1.Press and hold the SETUP button until CODE SETUP is displayed (takes about 3 seconds), then release the SETUP button.

2.Press the down navigation button until TIMER SETUP is displayed.

3.Press and release OK. TV SLEEP SETUP is displayed.

4.Press the down navigation button until the desired TIMER X SETUP is displayed (where “X” is 1, 2, 3 or 4) screen. Press and release OK.

5.TIMER X CLEAR is displayed. Press and release OK.

6.CONFIRM CLEAR is displayed. Press and release OK.

7.SUCCESS is displayed and the remote remains in Setup Mode, returning to the CODE SETUP screen. Press QUIT then OK to exit Setup Mode.

18

19

Image 10
Contents SRU6080 Table of Contents IntroductionButton Functions Button Functions, Liquid Crystal Display LCD Helps with setupRECORD,PLAY,STOP,REW,FF,PAUSE VCR control Replay code is DVD Functions labeled in BlueTivo/Replay Functions labeled in Yellow TiVo code is SAT FunctionsSetup Setup,Direct Code Entry Code EntryCode Entry, Searching for CodesSystem Setup Options Code Identification FeatureCode Identification Setting the Time of Day Time Setup Setting the Date Date SetupTimer Setup Setting the Backlighting On time Backlight SetupReset the LCD Remote to Factory Defaults System Reset Setting and Clearing a TV Sleep Timer TV Sleep SetupSetting and Clearing Timers Timer Setup To clear a Timer Timer Bell in normal displayTips On Learning, Code LearningLearning Notes Clearing Commands Learning CommandsTo Clear all Learned Commands under a mode Macros, To Setup a MacroMacros Macro NotesLimited Lifetime Warranty TroubleshootingRemote does not operate some features of your product Remote does not operate your productContenido IntroducciónFunciones de los botones Funciones de los botonescontinuaciónReplay el código es Funciones de TiVo/Replay en amarillo TiVo el código esPulgar HACIAARRIBA/ABAJO ajusta las Configuración Configuración continuaciónBúsqueda de códigos Introducción de códigosIntroducción directa de códigos Búsqueda de códigos por marcaOpciones de configuración del sistema Identificación de códigosConfiguración de la hora Time Setup Configuración de la fecha Date SetupConfiguración de temporizadores Restablecimiento del mando LCD a los ajustes de fábricaConfiguración y eliminación de temporizadores Timer Setup Consejos para el aprendizaje Aprendizaje de códigosNotas sobre el aprendizaje Aprendizaje de comandos Eliminación de comandosNotas sobre las macros Para configurar una macroMacros continuación Para eliminar una macroEl mando no acciona algunas funciones del producto Resolución de problemasEl mando no acciona el producto Garantía de duración limitadaTable des matières TV/VCR/DVRFonctions des boutons Fonctions des boutons suiteFonctions SAT Fonctions Tivo/Replay surlignées en jauneFonctions DVD en bleu TiVo codePréparation Préparation suiteSaisie de code directe Saisie de codeSaisie de code suite Recherche de codeIdentification de code Commande des appareils combinésCommande du volume / de la sourdine et fonction de perçage Programmation des codes des appareils combinésRéglage de l’heure Time Setup Réglage de la date Date SetupRéglage de la durée du rétroéclairage Backlight Setup Réglage du minuteurRéglage et annulation des minuteurs Timer Setup Conseils sur l’apprentissage Apprentissage des codesRemarques sur l’apprentissage Apprentissage des commandes Suppression des commandes Comment supprimer toutes les commandes apprises sous un modeRemarques sur les macros Comment régler une macroMacros suite Comment supprimer une macroLa télécommande ne commande pas votre produit Dépannage Garantie à vie limitéeSRU6080 Back Cover