Samson VHF TD Series, VHF Series specification

ENGLISH

Setting Up and Using Your

VHF TD Series/ VHF Series System

The basic procedure for setting up and using your VHF TD Series or VHF Series Wireless System takes only a few minutes:

1.For the VHF TD Series / VHF Series system to work correctly, both the receiver and transmitter must be set to the same channel. Remove all packing materials (save them in case of need for future service) and check to make sure that the supplied receiver and transmitter are set to the same channel. If these channels do not match, contact your distributor or, if purchased in the United States, Samson Technical Support at 1-800-372-6766.

2.Physically place the receiver where it will be used (the general rule of thumb is to maintain “line of sight” between the receiver and transmitter so that the person using or wearing the transmitter can see the receiver). An optional rack-mount kit (available from your Samson dealer) allows the VR3TD or VR3 to be mounted in a standard 19" rack if desired. Extend the antenna or antennas and place them in a vertical position.

3.Make sure the Power on-off switch in your VT3L / VT3 belt-pack or VH3 handheld transmitter is set to “Off.”

4a. If your system contains a VT3L or VT3 belt-pack transmitter, press gently inwards on both battery cover release indents to open the battery door. Note that this door is hinged and not intended to be removed from the transmitter case. Please use care when opening this door as undue force will destroy the hinge.

4b. If your system contains a VH3 handheld transmitter, unscrew the bottom section of the microphone by turning it counterclockwise and then slide it off.

5. Place a fresh 9-volt alkaline battery in the transmitter battery holder, taking care to observe the polarity markings. If you are using a VT3L or VT3 belt-pack transmitter, gen- tly replace the battery door by swinging it up and pressing until it clicks. If you are using a SH4 handheld transmitter, replace the bottom section of the microphone by sliding it on and then screwing it back on. Whichever transmitter you are using, leave it off for the moment.

6.Make the physical cable connection between the VR3TD or VR3 output jack and the line or mic level audio input of your amplifier or mixer. If you are using the balanced XLR jack (preferable, since it will deliver an electromagnetically cleaner signal), be sure to set the receiver rear panel Audio Output Level switch correctly. If required, both the balanced and unbalanced outputs can be used simultaneously. Leave your amplifier (and/or mixer) off at this time.

7.Turn the Volume knob on the VR3TD or VR3 completely counterclockwise. Using the strain relief, connect the supplied AC adapter to the DC Input on the rear panel of the VR3TD or VR3, then plug the adapter into any standard AC outlet. Press the front panel Power switch to turn on the VR3TD or VR3; the green “Power” LED will light up, but all other front panel LEDs will remain unlit.

8.Turn on the power to the VT3L, VT3 or VH3 transmitter (using its Power on-off switch); all three Battery strength LEDs will light if the battery is sufficiently strong. At this point, the “TX” LED on the front panel of the receiver will light. If you are using an VR3TD receiver, either the “A” or “B” yellow LED on the front panel will also light, depending upon which antenna is receiving the stronger signal.

VHF Series, VHF TD Series specifications

The Samson VHF TD Series represents a significant advancement in professional audio communication, designed specifically for high-performance applications. Tailored for a diverse range of environments, from small venues to large-scale performances, the VHF TD Series stands out for its reliable performance, user-friendly interface, and impressive sound quality.

One of the main features of the VHF TD Series is its frequency versatility. Operating within the VHF band, these audio systems deliver dependable wireless transmission with minimal interference. This is particularly beneficial in settings where multiple devices are used simultaneously, ensuring clear and uninterrupted audio signals. The series supports various frequency ranges, allowing users to select the most appropriate channel for their specific environment.

In addition to its frequency adaptability, the VHF TD Series is characterized by its robust construction. Built to withstand the rigors of both indoor and outdoor use, the system exhibits durability while maintaining a lightweight profile. This level of resilience ensures longevity and cost-effectiveness, making it ideal for touring musicians, event organizers, and venues looking for a reliable sound solution.

Another innovative characteristic of the VHF TD Series is its intuitive user interface. Equipped with easy-to-navigate controls and clear displays, users can quickly adjust settings and monitor performance without extensive technical knowledge. This design consideration allows performers to focus on their craft rather than struggling with complex equipment.

Furthermore, the VHF TD Series incorporates advanced audio processing technologies. These features include noise reduction capabilities, which diminish background noise and enhance vocal clarity. This is essential for presentations, conferences, and live performances, allowing the audience to experience rich and detailed sound.

Finally, the Samson VHF TD Series supports a wide range of accessories, such as handheld, lapel, and headset microphones, ensuring compatibility across various applications. This flexibility enables users to customize their setup to meet the demands of different events and environments.

In conclusion, the Samson VHF TD Series combines high-performance features with user-friendly designs, making it a go-to choice for professionals in the audio industry. With its robust durability, frequency versatility, intuitive controls, and advanced audio technologies, the VHF TD Series delivers exceptional sound quality for any audio communication need.