Philips 60P 8341, 64P8341, 64P8342, 50P8342 Setting the Start Time, Down twice to highlight FEA

Page 14

Features Menu • The Timer Control

11	12	1
10		2
9		3
8		4

75

6

SETTING THE START TIME

You can set the TV to turn itself on at a specific time, just as you

would an alarm clock. Follow these steps to set the Start Time.

BEGIN

Press the MENU/SELECT but-

ton on the remote control to show the on-screen menu.

Press the CURSOR RING

DOWN twice to highlight FEA-

TURES.

Press the CURSOR RING

RIGHT to enter the FEATURES menu.

Press the CURSOR RING RIGHT again. Then press the CUR- SOR RING DOWN once to high-

light the START TIME control.

Press the CURSOR RING

RIGHT again to highlight the time indicator area.

Press the NUMBER buttons to enter the correct time. If you make a mistake entering the time, use the CURSOR RING LEFT or RIGHT to move among the time input slots to make corrections. NOTE: You can also use the CURSOR RING UP or DOWN to cycle through digits to input the time.

Press the CURSOR RING UP or DOWN to select AM or PM.

Press the STATUS/EXIT button to

remove the menu from the screen.

SMART HELP

You can set STOP TIME similarly to the way you set START TIME. Instructions are on

the next page.

	PICTURE	TIMER
	SOUND	AUTOLOCK
		PIP
	FEATURES	PIP	FEATURES
	INSTALL	CLOSED CAP	FEATURES		TIME

				TIMER
				TIMER
				AUTOLOCK	START TIME
				PIP	STOP TIME
				PIP	STOP TIME
				CLOSED CAP	CHANNEL
					TUNER MODE

								FEATURES
				POWER				TIMER
								TIME	8:01 PM
								START TIME
								STOP TIME
								CHANNEL
	TV		VCR	ACC				TUNER MODE
	TV		VCR	ACC
	SWAP		PIP CH SOURCE FREEZE				5
7		DN	UP			4		FEATURES
				PICTURE				FEATURES
	SOUND			PICTURE	3			TIMER
								TIMER
								TIME
	STATUS/			MENU/				START TIME	_ _:_ _
	EXIT			SELECT				STOP TIME
								STOP TIME
8					HOME			CHANNEL
					HOME			TUNER MODE
			MUTE		1			TUNER MODE
	VOL			CH	1			FEATURES
			2					FEATURES
			2					TIMER
	1	4		3				TIME
	1			3				START TIME	8:00 AM
								START TIME	8:00 AM
	4		5	6				STOP TIME
	4		5	6				CHANNEL
						6		CHANNEL
	7		8	9				TUNER MODE
	7		8	9
	TV/VCR		0
	A/CH		0	SURF
		POSITION		PIP

14

Image 14

Contents Projection Television Warranty Verification Important Safety Instructions Table of Contents Features Digital-Ready Projection TVPress the Cursor Ring Right Adjusting the PictureScreen menu Press the MENU/SELECT but Press the Cursor Ring Right or Left to switch DNR onTurning on the Dynamic Noise Reduction DNR Control Press the STATUS/EXIT buttonTurning on the Imagemax Control Ton on the remote control to show the on-screen menuRight or LEFTto switch between on and OFF Press the Cursor RingConverge RED/BLUE Down repeatedly until MULTI- Point RED is selected Right to enter Navigate modeConverge Multipoint RED/BLUE Multipoint RED Press the MENU/SELECT but Ton to return to the ConvergenceMenu Save MultipointUndo Multipoint Undo MultipointDown repeatedly until Undo Multipoint is selected Press the Cursor Ring Down Setting the ClockPress the MENU/SELECT button Right again to highlight the time indicator area Setting the Start TimeRight to enter the Features menu Down twice to highlight FEARight to highlight the time indica- tor area Setting the Stop TimeHighlight the Stop Time control Press the Number buttons to Selecting the ChannelPress the Cursor Ring RIGHT. Then press the Cursor Enter the desired start-up channel. OrTuner Mode Selecting the TunerONCE, press the Cursor Ring Setting the Activate ControlPress the Cursor Ring Right again. Then press the CUR Cursor Ring Right againRight or Left to turn the Timer Display on or OFF Constantly Displaying the Time on ScreenUnderstanding Autolock Movie RatingsEnter a new four-digit code Setting UP the Access CodePress the Cursor Ring Right to highlight Access Enter your new four-digit codePress the Cursor Ring UP or Enter your four-digit AccessBlocking Channels Blocking by Movie Rating Right again to highlight AccessEnter your four-digit Access CODE. Correct will flash very Down repeatedly until Movie Rating is highlightedRight to enter the TV Rating menu Blocking by TV RatingING is highlighted Enter your four-digit Access Code Press the Cursor Ring Turning the Blocking Control on or OFFDown once to select Block Blocking Unrated BroadcastsRight to enter the Block Options menu Down twice to highlight no RAT- ING Right again to highlight Access Code input areaBlocking Broadcasts That have no Rating Press the Cursor Ring Right or Left to turn no RATSTATUS/EXIT button to remove Reviewing Your SettingsPress the STATUS/EXIT but Them from the screenClearing ALL Blocked Channels Right again to highlightDown repeatedly until the Closed CAP control is highlighted Using the Closed Captioning ControlDown to select a Caption Mode SOR Ring Right again to highTrol, press the Cursor Ring Adjusting the TREBLE, BASS, and BalanceThen Press the Cursor Ring Right or Left to adjust On or OFF Using the AVL Audio Volume Leveler ControlDown repeatedly until AVL is high Using Incredible Surround MonoSound Setting the TV for Stereo and SAPDown once to highlight Sound menu TreblePress the Cursor Ring Left Setting the Audio OUT ControlDown repeatedly until Audio OUT is highlighted Or Right to set the Audio OUT to Variable or FixedTon to remove the menu from the screen Using the TV Speaker Control and Audio OutputsTo hear the TV sound from only the audio system speakers Using the Bass Boost Control Press the Picture button Using AutopicturePress the Picture button on AutoSound setting will appear in the middle of the screen Using AutosoundPress the Sound button on the remote control. The current AutoSound ChoicesUsing SURF, Alternate CHANNEL, and Program List SurfSleep Using the Sleep Timer ControlSleep OFF Tons to adjust the TV’s sound level Using the Volume ButtonsPress the VOLume +,- but VolumeUsing the AV Button CV1 TUNER-B TUNER-ADoes the remote turn the accessory device on? Setting the TV Remote to Work Accessory DevicesDesired accessory device and press the Power button Please read through all the steps before beginning Search Method Ry device and continue holding the buttons downSetting the TV Remote to Work Accessories See the next page for more codesSatellite Receiver Brand Remote Codes Using PIP Basic Connections Cable TV Signal Company RF Coaxial Cable 75 Ohm PIP WindowCan press the PIP CHannel DN/UP Selecting the PIP Signal SourceInput on the back of the TV, you Buttons to change channels in the PIP windowShow the PIP window again Using the PIP Remote Control ButtonsPress the PIP ON/OFF button to To remove PIP from the screenPress the Cursor Ring Down twice to highlight FEA Adjusting the PIP Color and Tint ControlsPress the Cursor Ring Right to enter the Features Connect the other RF coaxial Using Connection OptionsConnect a cable TV signal to a Use another RF coaxial cable to Connect two RF coaxial cables toCable to the INput on the cable box Helpful Hints Glossary of Television Terms Index Factory Service Locations CanadaHouston Limited Warranty Projection Television