Philips 55P8342 manual Using Autosound, Press the Sound button on the remote control. The current

Page 39

Remote Control • AutoSound

USING AUTOSOUND

AutoSound allows you to select from three factory-set controls and a personal control that you set according to your own preferences through the on-screen Sound menu.

The three factory-set controls (Voice, Music, and Theatre) enable you to tailor the TV sound so as to enhance the particular program you are watching. Follow these steps to select any of the options.

BEGIN

Press the SOUND button on the remote control. The current

AutoSound setting will appear in the middle of the screen.

Press the SOUND button repeat- edly to cycle through the four set- tings: PERSONAL, VOICE, MUSIC, or THEATRE.

SMART HELP

You determine the PER- SONAL setting by adjust-

ments you make within the SOUND menu. The other AutoSound set- tings are made at the factory and cannot be adjusted.

AutoSound works only with the pro- grams coming through the ANTEN- NA/CABLE (ANT “A” or PIP ANT “B”) inputs on the back of the TV. AutoSound will not control the sound levels of the other inputs on the back of the TV set.

AutoSound Choices

PERSONAL—presents the TV’s sound according to the settings you make within the SOUND menu.

VOICE—brings voices to the fore- front and emphasizes them. Moves music to the background.

MUSIC—emphasizes music over voices.

THEATRE—provides a balance between voices and music.

	PERSONAL
TREBLE
TREBLE		49
BASS		49

				POWER
2	1	TV	VCR	ACC
	1	SWAP	PIP CH	SOURCE FREEZE
		DN	UP
		SOUND		PICTURE
		STATUS/		MENU/
		EXIT		SELECT
			MUTE
		VOL		CH

1 2 3

4 5 6

7 8 9

TV/VCR

A/CH	0	SURF
POSITION		PIP


	VOICE
TREBLE			56


BASS				47


		MUSIC
TREBLE			63


BASS				69


		THEATRE
TREBLE			60


BASS				72

39

Image 39

Contents Projection Television Warranty Verification Important Safety Instructions Table of Contents Digital-Ready Projection TV FeaturesAdjusting the Picture Screen menuPress the Cursor Ring Right Press the STATUS/EXIT button Press the Cursor Ring Right or Left to switch DNR onTurning on the Dynamic Noise Reduction DNR Control Press the MENU/SELECT butPress the Cursor Ring Ton on the remote control to show the on-screen menuRight or LEFTto switch between on and OFF Turning on the Imagemax ControlConverge RED/BLUE Right to enter Navigate mode Converge Multipoint RED/BLUEDown repeatedly until MULTI- Point RED is selected Save Multipoint Press the MENU/SELECT but Ton to return to the ConvergenceMenu Multipoint REDUndo Multipoint Down repeatedly until Undo Multipoint is selectedUndo Multipoint Setting the Clock Press the MENU/SELECT buttonPress the Cursor Ring Down Down twice to highlight FEA Setting the Start TimeRight to enter the Features menu Right again to highlight the time indicator areaSetting the Stop Time Highlight the Stop Time controlRight to highlight the time indica- tor area Enter the desired start-up channel. Or Selecting the ChannelPress the Cursor Ring RIGHT. Then press the Cursor Press the Number buttons toSelecting the Tuner Tuner ModeCursor Ring Right again Setting the Activate ControlPress the Cursor Ring Right again. Then press the CUR ONCE, press the Cursor RingConstantly Displaying the Time on Screen Right or Left to turn the Timer Display on or OFFMovie Ratings Understanding AutolockEnter your new four-digit code Setting UP the Access CodePress the Cursor Ring Right to highlight Access Enter a new four-digit codeEnter your four-digit Access Blocking ChannelsPress the Cursor Ring UP or Down repeatedly until Movie Rating is highlighted Right again to highlight AccessEnter your four-digit Access CODE. Correct will flash very Blocking by Movie RatingBlocking by TV Rating ING is highlightedRight to enter the TV Rating menu Turning the Blocking Control on or OFF Enter your four-digit Access Code Press the Cursor RingBlocking Unrated Broadcasts Right to enter the Block Options menuDown once to select Block Press the Cursor Ring Right or Left to turn no RAT Right again to highlight Access Code input areaBlocking Broadcasts That have no Rating Down twice to highlight no RAT- INGThem from the screen Reviewing Your SettingsPress the STATUS/EXIT but STATUS/EXIT button to removeRight again to highlight Clearing ALL Blocked ChannelsSOR Ring Right again to high Using the Closed Captioning ControlDown to select a Caption Mode Down repeatedly until the Closed CAP control is highlightedAdjusting the TREBLE, BASS, and Balance Then Press the Cursor Ring Right or Left to adjustTrol, press the Cursor Ring Using the AVL Audio Volume Leveler Control Down repeatedly until AVL is highOn or OFF Mono Using Incredible SurroundTreble Setting the TV for Stereo and SAPDown once to highlight Sound menu SoundOr Right to set the Audio OUT to Variable or Fixed Setting the Audio OUT ControlDown repeatedly until Audio OUT is highlighted Press the Cursor Ring LeftUsing the TV Speaker Control and Audio Outputs To hear the TV sound from only the audio system speakersTon to remove the menu from the screen Using the Bass Boost Control Using Autopicture Press the Picture button onPress the Picture button AutoSound Choices Using AutosoundPress the Sound button on the remote control. The current AutoSound setting will appear in the middle of the screenSurf Using SURF, Alternate CHANNEL, and Program ListUsing the Sleep Timer Control Sleep OFFSleep Volume Using the Volume ButtonsPress the VOLume +,- but Tons to adjust the TV’s sound levelCV1 TUNER-B TUNER-A Using the AV ButtonSetting the TV Remote to Work Accessory Devices Desired accessory device and press the Power buttonDoes the remote turn the accessory device on? Please read through all the steps before beginning Ry device and continue holding the buttons down Search MethodSee the next page for more codes Setting the TV Remote to Work AccessoriesSatellite Receiver Brand Remote Codes Cable TV Signal Company RF Coaxial Cable 75 Ohm PIP Window Using PIP Basic ConnectionsButtons to change channels in the PIP window Selecting the PIP Signal SourceInput on the back of the TV, you Can press the PIP CHannel DN/UPTo remove PIP from the screen Using the PIP Remote Control ButtonsPress the PIP ON/OFF button to Show the PIP window againAdjusting the PIP Color and Tint Controls Press the Cursor Ring Right to enter the FeaturesPress the Cursor Ring Down twice to highlight FEA Using Connection Options Connect a cable TV signal to aConnect the other RF coaxial Connect two RF coaxial cables to Cable to the INput on the cable boxUse another RF coaxial cable to Helpful Hints Glossary of Television Terms Index Canada Factory Service LocationsHouston Projection Television Limited Warranty