Philips 64P8342, 64P8341, 50P8342, 50P 8341, 60P8342, 55P 8341, 60P 8341, 55P8342 Converge RED/BLUE

Page 9

Picture Menu • The Convergence Control

CONVERGE RED/BLUE

The influence of magnetic fields and changes in the position of the

TV may cause screen colors not to line up properly. The result on your TV screen will be red or blue colors appearing around the edges of images.

If various images on the entire picture have red outlines, adjust the CON- VERGE RED control. Then if any red outlines remain, adjust the MULTI- POINT RED control.

If various images on the entire picture have blue outlines, adjust the CON- VERGE BLUE control. Then if any blue outlines remain, adjust the MUL- TIPOINT BLUE control.

Use the UNDO MULTIPOINT control if you want to restore the picture screen to the way it was before you made Multipoint adjustments.

NOTE: After turning the TV set on, allow it to warm up for 15 minutes before adjusting the Convergence controls.

BEGIN

Press the MENU/SELECT but-

ton on the remote control to show the on-screen menu.

Press the CURSOR RING

RIGHT to enter the PICTURE menu.

Press the CURSOR RING

DOWN repeatedly until CONVER-

GENCE is selected.

Press the CURSOR RING

RIGHT to enter the CONVER-

GENCE menu.

Press the CURSOR RING

RIGHT to enter CONVERGE RED mode.

Press the CURSOR RING LEFT, RIGHT, UP, or DOWN to

adjust the cross image until the color outline around it is gone.

Press the STATUS/EXIT button

to exit the menu from the screen.

PICTURE
	TINT	CONVERGE RED
	COLOR TEMP	CONVERGE BLUE	PICTURE
	DNR	MULTIPOINT RED		CONVERGENCE
	IMAGEMAX	MULTIPOINT BLUE
	IMAGEMAX	MULTIPOINT BLUE		CONVERGE RED
	CONVERGENCE	SAVE MULTIPOINT		CONVERGE RED
	CONVERGENCE	SAVE MULTIPOINT		CONVERGE BLUE
				CONVERGE BLUE
				MULTIPOINT RED
				MULTIPOINT RED
				MULTIPOINT BLUE
				SAVE MULTIPOINT

POWER

CONVERGE RED

	TV	VCR	ACC	5
	SWAP	PIP CH	SOURCE FREEZE	4
6	DN	UP		4
6	SOUND		PICTURE	2
				CONVERGE RED
	STATUS/		MENU/
	EXIT		SELECT
7		MUTE		1
	VOL		CH	1
		3
	1	2	3
	4	5	6	SMART HELP
	7	8	9	You can adjust the CON-
	TV/VCR	0		VERGE BLUE control the
	A/CH	0	SURF	same way you would the CON-
				same way you would the CON-
	POSITION		PIP	VERGE RED control.

PICTURE
CONVERGENCE
CONVERGE RED
CONVERGE BLUE
MULTIPOINT RED
MULTIPOINT BLUE	CONVERGE BLUE	CONVERGE BLUE
SAVE MULTIPOINT	CONVERGE BLUE	CONVERGE BLUE

9

Image 9

Contents Projection Television Warranty Verification Important Safety Instructions Table of Contents Digital-Ready Projection TV FeaturesAdjusting the Picture Screen menuPress the Cursor Ring Right Turning on the Dynamic Noise Reduction DNR Control Press the Cursor Ring Right or Left to switch DNR onPress the MENU/SELECT but Press the STATUS/EXIT buttonRight or LEFTto switch between on and OFF Ton on the remote control to show the on-screen menuTurning on the Imagemax Control Press the Cursor RingConverge RED/BLUE Right to enter Navigate mode Converge Multipoint RED/BLUEDown repeatedly until MULTI- Point RED is selected Menu Press the MENU/SELECT but Ton to return to the ConvergenceMultipoint RED Save MultipointUndo Multipoint Down repeatedly until Undo Multipoint is selectedUndo Multipoint Setting the Clock Press the MENU/SELECT buttonPress the Cursor Ring Down Right to enter the Features menu Setting the Start TimeRight again to highlight the time indicator area Down twice to highlight FEASetting the Stop Time Highlight the Stop Time controlRight to highlight the time indica- tor area Press the Cursor Ring RIGHT. Then press the Cursor Selecting the ChannelPress the Number buttons to Enter the desired start-up channel. OrSelecting the Tuner Tuner ModePress the Cursor Ring Right again. Then press the CUR Setting the Activate ControlONCE, press the Cursor Ring Cursor Ring Right againConstantly Displaying the Time on Screen Right or Left to turn the Timer Display on or OFFMovie Ratings Understanding AutolockPress the Cursor Ring Right to highlight Access Setting UP the Access CodeEnter a new four-digit code Enter your new four-digit codeEnter your four-digit Access Blocking ChannelsPress the Cursor Ring UP or Enter your four-digit Access CODE. Correct will flash very Right again to highlight AccessBlocking by Movie Rating Down repeatedly until Movie Rating is highlightedBlocking by TV Rating ING is highlightedRight to enter the TV Rating menu Turning the Blocking Control on or OFF Enter your four-digit Access Code Press the Cursor RingBlocking Unrated Broadcasts Right to enter the Block Options menuDown once to select Block Blocking Broadcasts That have no Rating Right again to highlight Access Code input areaDown twice to highlight no RAT- ING Press the Cursor Ring Right or Left to turn no RATPress the STATUS/EXIT but Reviewing Your SettingsSTATUS/EXIT button to remove Them from the screenRight again to highlight Clearing ALL Blocked ChannelsDown to select a Caption Mode Using the Closed Captioning ControlDown repeatedly until the Closed CAP control is highlighted SOR Ring Right again to highAdjusting the TREBLE, BASS, and Balance Then Press the Cursor Ring Right or Left to adjustTrol, press the Cursor Ring Using the AVL Audio Volume Leveler Control Down repeatedly until AVL is highOn or OFF Mono Using Incredible SurroundDown once to highlight Sound menu Setting the TV for Stereo and SAPSound TrebleDown repeatedly until Audio OUT is highlighted Setting the Audio OUT ControlPress the Cursor Ring Left Or Right to set the Audio OUT to Variable or FixedUsing the TV Speaker Control and Audio Outputs To hear the TV sound from only the audio system speakersTon to remove the menu from the screen Using the Bass Boost Control Using Autopicture Press the Picture button onPress the Picture button Press the Sound button on the remote control. The current Using AutosoundAutoSound setting will appear in the middle of the screen AutoSound ChoicesSurf Using SURF, Alternate CHANNEL, and Program ListUsing the Sleep Timer Control Sleep OFFSleep Press the VOLume +,- but Using the Volume ButtonsTons to adjust the TV’s sound level VolumeCV1 TUNER-B TUNER-A Using the AV ButtonSetting the TV Remote to Work Accessory Devices Desired accessory device and press the Power buttonDoes the remote turn the accessory device on? Please read through all the steps before beginning Ry device and continue holding the buttons down Search MethodSee the next page for more codes Setting the TV Remote to Work AccessoriesSatellite Receiver Brand Remote Codes Cable TV Signal Company RF Coaxial Cable 75 Ohm PIP Window Using PIP Basic ConnectionsInput on the back of the TV, you Selecting the PIP Signal SourceCan press the PIP CHannel DN/UP Buttons to change channels in the PIP windowPress the PIP ON/OFF button to Using the PIP Remote Control ButtonsShow the PIP window again To remove PIP from the screenAdjusting the PIP Color and Tint Controls Press the Cursor Ring Right to enter the FeaturesPress the Cursor Ring Down twice to highlight FEA Using Connection Options Connect a cable TV signal to aConnect the other RF coaxial Connect two RF coaxial cables to Cable to the INput on the cable boxUse another RF coaxial cable to Helpful Hints Glossary of Television Terms Index Canada Factory Service LocationsHouston Projection Television Limited Warranty