Philips 55P8342, 64P8341, 64P8342, 50P8342 Setting the Stop Time, Highlight the Stop Time control

Page 15

SETTING THE STOP TIME

Features Menu • The Timer Control

11	12	1
10		2
9		3
8		4
7	6	5

Use the START TIME control to set the TV to turn itself on at a

specific time (see the previous page). The following steps will guide you in setting the TV to turn itself off.

BEGIN

Press the MENU/SELECT but-

ton on the remote control to show the on-screen menu.

Press the CURSOR RING

DOWN twice to highlight FEA-

TURES.

Press the CURSOR RING

RIGHT to enter the FEATURES menu.

Press the CURSOR RING RIGHT again. Then press the CURSOR RING DOWN twice to

highlight the STOP TIME control.

Press the CURSOR RING

RIGHT to highlight the time indica- tor area.

Press the NUMBER buttons to enter the correct time. If you make a mistake entering the time, use the CURSOR RING LEFT or RIGHT to move among the input slots to make corrections. NOTE: You can also use the CURSOR RING UP or DOWN to cycle through digits to input the time.

Press the CURSOR RING UP or DOWN to select AM or PM.

Press the STATUS/EXIT button

to remove the menu from the screen.

	PICTURE	TIMER
	SOUND	AUTOLOCK
		PIP
	FEATURES	PIP	FEATURES
	INSTALL	CLOSED CAP	FEATURES		TIME

				TIMER
				TIMER
				AUTOLOCK	START TIME
				PIP	STOP TIME
				PIP	STOP TIME
				CLOSED CAP	CHANNEL
					TUNER MODE

						FEATURES
				POWER		TIMER
						TIME	8:02 PM
						START TIME
						STOP TIME
						CHANNEL
	TV		VCR	ACC		TUNER MODE
	TV		VCR	ACC		5
	SWAP	PIP CH		SOURCE FREEZE	4	5
		DN	UP			FEATURES
						FEATURES
	SOUND			PICTURE	3	TIMER
	7					TIME
	7			MENU/		START TIME
	EXIT			SELECT		STOP TIME	_ _:_ _
						STOP TIME	_ _:_ _
						CHANNEL
					1	TUNER MODE
8			MUTE
	VOL			CH		FEATURES
			2			FEATURES
		4				TIMER
						TIME
				3

						START TIME
						START TIME
	4		5	6		STOP TIME	9:30 AM
	4		5	6		CHANNEL
						CHANNEL
	7		8	9		TUNER MODE
	7		8	9	6
	TV/VCR		0
	A/CH		0	SURF
		POSITION		PIP

15

Image 15

Contents Projection Television Warranty Verification Important Safety Instructions Table of Contents Digital-Ready Projection TV FeaturesAdjusting the Picture Screen menuPress the Cursor Ring Right Press the STATUS/EXIT button Press the Cursor Ring Right or Left to switch DNR onTurning on the Dynamic Noise Reduction DNR Control Press the MENU/SELECT butPress the Cursor Ring Ton on the remote control to show the on-screen menuRight or LEFTto switch between on and OFF Turning on the Imagemax ControlConverge RED/BLUE Right to enter Navigate mode Converge Multipoint RED/BLUEDown repeatedly until MULTI- Point RED is selected Save Multipoint Press the MENU/SELECT but Ton to return to the ConvergenceMenu Multipoint RED Undo Multipoint Down repeatedly until Undo Multipoint is selected Undo Multipoint Setting the Clock Press the MENU/SELECT buttonPress the Cursor Ring Down Down twice to highlight FEA Setting the Start TimeRight to enter the Features menu Right again to highlight the time indicator areaSetting the Stop Time Highlight the Stop Time controlRight to highlight the time indica- tor area Enter the desired start-up channel. Or Selecting the ChannelPress the Cursor Ring RIGHT. Then press the Cursor Press the Number buttons toSelecting the Tuner Tuner ModeCursor Ring Right again Setting the Activate ControlPress the Cursor Ring Right again. Then press the CUR ONCE, press the Cursor RingConstantly Displaying the Time on Screen Right or Left to turn the Timer Display on or OFFMovie Ratings Understanding AutolockEnter your new four-digit code Setting UP the Access CodePress the Cursor Ring Right to highlight Access Enter a new four-digit codeEnter your four-digit Access Blocking ChannelsPress the Cursor Ring UP or Down repeatedly until Movie Rating is highlighted Right again to highlight AccessEnter your four-digit Access CODE. Correct will flash very Blocking by Movie RatingBlocking by TV Rating ING is highlightedRight to enter the TV Rating menu Turning the Blocking Control on or OFF Enter your four-digit Access Code Press the Cursor RingBlocking Unrated Broadcasts Right to enter the Block Options menuDown once to select Block Press the Cursor Ring Right or Left to turn no RAT Right again to highlight Access Code input areaBlocking Broadcasts That have no Rating Down twice to highlight no RAT- INGThem from the screen Reviewing Your SettingsPress the STATUS/EXIT but STATUS/EXIT button to removeRight again to highlight Clearing ALL Blocked ChannelsSOR Ring Right again to high Using the Closed Captioning ControlDown to select a Caption Mode Down repeatedly until the Closed CAP control is highlightedAdjusting the TREBLE, BASS, and Balance Then Press the Cursor Ring Right or Left to adjustTrol, press the Cursor Ring Using the AVL Audio Volume Leveler Control Down repeatedly until AVL is highOn or OFF Mono Using Incredible SurroundTreble Setting the TV for Stereo and SAPDown once to highlight Sound menu SoundOr Right to set the Audio OUT to Variable or Fixed Setting the Audio OUT ControlDown repeatedly until Audio OUT is highlighted Press the Cursor Ring LeftUsing the TV Speaker Control and Audio Outputs To hear the TV sound from only the audio system speakersTon to remove the menu from the screen Using the Bass Boost Control Using Autopicture Press the Picture button onPress the Picture button AutoSound Choices Using AutosoundPress the Sound button on the remote control. The current AutoSound setting will appear in the middle of the screenSurf Using SURF, Alternate CHANNEL, and Program ListUsing the Sleep Timer Control Sleep OFFSleep Volume Using the Volume ButtonsPress the VOLume +,- but Tons to adjust the TV’s sound levelCV1 TUNER-B TUNER-A Using the AV ButtonSetting the TV Remote to Work Accessory Devices Desired accessory device and press the Power buttonDoes the remote turn the accessory device on? Please read through all the steps before beginning Ry device and continue holding the buttons down Search MethodSee the next page for more codes Setting the TV Remote to Work AccessoriesSatellite Receiver Brand Remote Codes Cable TV Signal Company RF Coaxial Cable 75 Ohm PIP Window Using PIP Basic ConnectionsButtons to change channels in the PIP window Selecting the PIP Signal SourceInput on the back of the TV, you Can press the PIP CHannel DN/UPTo remove PIP from the screen Using the PIP Remote Control ButtonsPress the PIP ON/OFF button to Show the PIP window againAdjusting the PIP Color and Tint Controls Press the Cursor Ring Right to enter the FeaturesPress the Cursor Ring Down twice to highlight FEA Using Connection Options Connect a cable TV signal to aConnect the other RF coaxial Connect two RF coaxial cables to Cable to the INput on the cable boxUse another RF coaxial cable to Helpful Hints Glossary of Television Terms Index Canada Factory Service LocationsHouston Projection Television Limited Warranty