Philips 64P8341 manual Selecting the Channel, Press the Cursor Ring RIGHT. Then press the Cursor

Page 16

Features Menu • The Timer Control

11	12	1
10		2
9		3
8		4

75

6

SELECTING THE CHANNEL

You can select a specific channel that the television will tune to

when the timer turns the set on. Follow these steps to select the chan- nel.

BEGIN

Press the MENU/SELECT but-

ton on the remote control to show the on-screen menu.

Press the CURSOR RING

DOWN twice to highlight FEA-

TURES.

Press the CURSOR RING

RIGHT to enter the FEATURES menu.

Press the CURSOR RING RIGHT. Then press the CURSOR

RING DOWN repeatedly until the CHANNEL control is highlighted.

Press the NUMBER buttons to

enter the desired start-up channel. Or

press the CURSOR RING RIGHT

repeatedly to enter the start-up channel you want.

Press the STATUS/EXIT button

to remove the menu from the screen.

	PICTURE		TIMER
	SOUND		AUTOLOCK
	FEATURES		PIP		FEATURES
	INSTALL		CLOSED CAP		TIMER	TIME
					TIMER	TIME
					AUTOLOCK	START TIME
					PIP	STOP TIME
					CLOSED CAP	CHANNEL
						TUNER MODE
					FEATURES
			POWER		TIMER
					TIME		8:03 PM
					START TIME
					STOP TIME
					CHANNEL
	TV	VCR	ACC		TUNER MODE
	TV	VCR	ACC
	SWAP	PIP CH	SOURCE FREEZE	4
	DN	UP			FEATURES
					FEATURES
	SOUND		PICTURE	3	TIMER
				3	TIMER
					TIME
	STATUS/		MENU/		START TIME
	STATUS/		MENU/		STOP TIME
	EXIT		SELECT

					CHANNEL		12
				1	TUNER MODE
6		MUTE
6	VOL		CH		FEATURES
			2		FEATURES
	4				TIMER
	4					TIME
	1		3			START TIME	10:30 AM
						START TIME	10:30 AM
	4	5	6			STOP TIME
	4	5	6			CHANNEL	12
						CHANNEL	12
	7	8	9			TUNER MODE
	7	8	9
	TV/VCR	0
	A/CH	0	SURF
	POSITION		PIP

16

Image 16

Contents Projection Television Warranty Verification Important Safety Instructions Table of Contents Features Digital-Ready Projection TVScreen menu Adjusting the PicturePress the Cursor Ring Right Press the Cursor Ring Right or Left to switch DNR on Turning on the Dynamic Noise Reduction DNR ControlPress the MENU/SELECT but Press the STATUS/EXIT buttonTon on the remote control to show the on-screen menu Right or LEFTto switch between on and OFFTurning on the Imagemax Control Press the Cursor RingConverge RED/BLUE Converge Multipoint RED/BLUE Right to enter Navigate modeDown repeatedly until MULTI- Point RED is selected Press the MENU/SELECT but Ton to return to the Convergence MenuMultipoint RED Save MultipointDown repeatedly until Undo Multipoint is selected Undo MultipointUndo Multipoint Press the MENU/SELECT button Setting the ClockPress the Cursor Ring Down Setting the Start Time Right to enter the Features menuRight again to highlight the time indicator area Down twice to highlight FEAHighlight the Stop Time control Setting the Stop TimeRight to highlight the time indica- tor area Selecting the Channel Press the Cursor Ring RIGHT. Then press the CursorPress the Number buttons to Enter the desired start-up channel. OrTuner Mode Selecting the TunerSetting the Activate Control Press the Cursor Ring Right again. Then press the CURONCE, press the Cursor Ring Cursor Ring Right againRight or Left to turn the Timer Display on or OFF Constantly Displaying the Time on ScreenUnderstanding Autolock Movie RatingsSetting UP the Access Code Press the Cursor Ring Right to highlight AccessEnter a new four-digit code Enter your new four-digit codeBlocking Channels Enter your four-digit AccessPress the Cursor Ring UP or Right again to highlight Access Enter your four-digit Access CODE. Correct will flash veryBlocking by Movie Rating Down repeatedly until Movie Rating is highlightedING is highlighted Blocking by TV RatingRight to enter the TV Rating menu Enter your four-digit Access Code Press the Cursor Ring Turning the Blocking Control on or OFFRight to enter the Block Options menu Blocking Unrated BroadcastsDown once to select Block Right again to highlight Access Code input area Blocking Broadcasts That have no RatingDown twice to highlight no RAT- ING Press the Cursor Ring Right or Left to turn no RATReviewing Your Settings Press the STATUS/EXIT butSTATUS/EXIT button to remove Them from the screenClearing ALL Blocked Channels Right again to highlightUsing the Closed Captioning Control Down to select a Caption ModeDown repeatedly until the Closed CAP control is highlighted SOR Ring Right again to highThen Press the Cursor Ring Right or Left to adjust Adjusting the TREBLE, BASS, and BalanceTrol, press the Cursor Ring Down repeatedly until AVL is high Using the AVL Audio Volume Leveler ControlOn or OFF Using Incredible Surround MonoSetting the TV for Stereo and SAP Down once to highlight Sound menuSound TrebleSetting the Audio OUT Control Down repeatedly until Audio OUT is highlightedPress the Cursor Ring Left Or Right to set the Audio OUT to Variable or FixedTo hear the TV sound from only the audio system speakers Using the TV Speaker Control and Audio OutputsTon to remove the menu from the screen Using the Bass Boost Control Press the Picture button on Using AutopicturePress the Picture button Using Autosound Press the Sound button on the remote control. The currentAutoSound setting will appear in the middle of the screen AutoSound ChoicesUsing SURF, Alternate CHANNEL, and Program List SurfSleep OFF Using the Sleep Timer ControlSleep Using the Volume Buttons Press the VOLume +,- butTons to adjust the TV’s sound level VolumeUsing the AV Button CV1 TUNER-B TUNER-ADesired accessory device and press the Power button Setting the TV Remote to Work Accessory DevicesDoes the remote turn the accessory device on? Please read through all the steps before beginning Search Method Ry device and continue holding the buttons downSetting the TV Remote to Work Accessories See the next page for more codesSatellite Receiver Brand Remote Codes Using PIP Basic Connections Cable TV Signal Company RF Coaxial Cable 75 Ohm PIP WindowSelecting the PIP Signal Source Input on the back of the TV, youCan press the PIP CHannel DN/UP Buttons to change channels in the PIP windowUsing the PIP Remote Control Buttons Press the PIP ON/OFF button toShow the PIP window again To remove PIP from the screenPress the Cursor Ring Right to enter the Features Adjusting the PIP Color and Tint ControlsPress the Cursor Ring Down twice to highlight FEA Connect a cable TV signal to a Using Connection OptionsConnect the other RF coaxial Cable to the INput on the cable box Connect two RF coaxial cables toUse another RF coaxial cable to Helpful Hints Glossary of Television Terms Index Factory Service Locations CanadaHouston Limited Warranty Projection Television