Philips 60P8342, 64P8341, 64P8342, 50P8342, 50P 8341 Setting the TV Remote to Work Accessory Devices

Page 44

Remote Control • Working Accessory Devices

SETTING THE TV REMOTE TO WORK ACCESSORY DEVICES

Your TV remote is capable of work- ing not only your TV but also

infrared remote (IR) controlled devices such as VCRs, cable TV con- verter boxes, satellite receivers, DVD players, and laser disc players.

If you want to use your TV remote to operate a VCR or other accessory device, you will need to perform this initial check explained in this sec- tion. You may also need to go to the sections on the “Direct Access Method” and the “Search Method” in the pages that follow.

BEGIN

Press the VCR or ACC(essory) mode button on the TV remote for the desired accessory device category.

NOTE: pressing the ACC(essory) mode button allows access to the product codes for cable TV convert- ers, DVD players, satellite receivers, and laser disc players.

Point the TV remote toward the

TV Remote

VCR/Accessory

Mode Buttons

TV	VCR	ACC
SWAP	PIP CH	SOURCE FREEZE
DN	UP
SOUND		PICTURE

1

VCR

2

POWER

desired accessory device and press the POWER button.

Does the remote turn the accessory device on?

If yes, and try other function but- tons on the TV remote. If they also work the accessory device, then the remote is ready and no further steps are needed.

If no, do the following:

Look up a three-digit remote code number on page 47 or 48 for your brand of accessory device. Then go through the simple Direct Access Method steps shown on page 45.

SMART HELP

If more than one number is listed, you may have to try

more than the first three-digit code given to locate your device’s correct code.

Satellite

Receiver

Cable Converter

		ACC
	VCR	SOURCE	FREEZE
	PIP	SOURCE	PICTURE
TV	PIP	U	PICTURE
OK	CH	P
		UP
SWAP	DN
SWAP	DN
			MENU/
	SOUND		SELECT
		STATUS/	CH
		EXIT	CH
			MUTE

VOL	3
VOL	3
2	6
2	6
	6
1	5
1	5	9
	5	9
		9
4	8
4	8	SURFCC
	8	SURFCC
7		0
7		0
	TV/VCR	0
	TV/VCR
	A/CH	PIP
	A/CH
		POSITION

44

Image 44

Contents Projection Television Warranty Verification Important Safety Instructions Table of Contents Features Digital-Ready Projection TVPress the Cursor Ring Right Adjusting the PictureScreen menu Press the Cursor Ring Right or Left to switch DNR on Turning on the Dynamic Noise Reduction DNR ControlPress the MENU/SELECT but Press the STATUS/EXIT buttonTon on the remote control to show the on-screen menu Right or LEFTto switch between on and OFFTurning on the Imagemax Control Press the Cursor RingConverge RED/BLUE Down repeatedly until MULTI- Point RED is selected Right to enter Navigate modeConverge Multipoint RED/BLUE Press the MENU/SELECT but Ton to return to the Convergence MenuMultipoint RED Save MultipointUndo Multipoint Undo MultipointDown repeatedly until Undo Multipoint is selected Press the Cursor Ring Down Setting the ClockPress the MENU/SELECT button Setting the Start Time Right to enter the Features menuRight again to highlight the time indicator area Down twice to highlight FEARight to highlight the time indica- tor area Setting the Stop TimeHighlight the Stop Time control Selecting the Channel Press the Cursor Ring RIGHT. Then press the CursorPress the Number buttons to Enter the desired start-up channel. OrTuner Mode Selecting the TunerSetting the Activate Control Press the Cursor Ring Right again. Then press the CURONCE, press the Cursor Ring Cursor Ring Right againRight or Left to turn the Timer Display on or OFF Constantly Displaying the Time on ScreenUnderstanding Autolock Movie RatingsSetting UP the Access Code Press the Cursor Ring Right to highlight AccessEnter a new four-digit code Enter your new four-digit codePress the Cursor Ring UP or Enter your four-digit AccessBlocking Channels Right again to highlight Access Enter your four-digit Access CODE. Correct will flash veryBlocking by Movie Rating Down repeatedly until Movie Rating is highlightedRight to enter the TV Rating menu Blocking by TV RatingING is highlighted Enter your four-digit Access Code Press the Cursor Ring Turning the Blocking Control on or OFFDown once to select Block Blocking Unrated BroadcastsRight to enter the Block Options menu Right again to highlight Access Code input area Blocking Broadcasts That have no RatingDown twice to highlight no RAT- ING Press the Cursor Ring Right or Left to turn no RATReviewing Your Settings Press the STATUS/EXIT butSTATUS/EXIT button to remove Them from the screenClearing ALL Blocked Channels Right again to highlightUsing the Closed Captioning Control Down to select a Caption ModeDown repeatedly until the Closed CAP control is highlighted SOR Ring Right again to highTrol, press the Cursor Ring Adjusting the TREBLE, BASS, and BalanceThen Press the Cursor Ring Right or Left to adjust On or OFF Using the AVL Audio Volume Leveler ControlDown repeatedly until AVL is high Using Incredible Surround MonoSetting the TV for Stereo and SAP Down once to highlight Sound menuSound TrebleSetting the Audio OUT Control Down repeatedly until Audio OUT is highlightedPress the Cursor Ring Left Or Right to set the Audio OUT to Variable or FixedTon to remove the menu from the screen Using the TV Speaker Control and Audio OutputsTo hear the TV sound from only the audio system speakers Using the Bass Boost Control Press the Picture button Using AutopicturePress the Picture button on Using Autosound Press the Sound button on the remote control. The currentAutoSound setting will appear in the middle of the screen AutoSound ChoicesUsing SURF, Alternate CHANNEL, and Program List SurfSleep Using the Sleep Timer ControlSleep OFF Using the Volume Buttons Press the VOLume +,- butTons to adjust the TV’s sound level VolumeUsing the AV Button CV1 TUNER-B TUNER-ADoes the remote turn the accessory device on? Setting the TV Remote to Work Accessory DevicesDesired accessory device and press the Power button Please read through all the steps before beginning Search Method Ry device and continue holding the buttons downSetting the TV Remote to Work Accessories See the next page for more codesSatellite Receiver Brand Remote Codes Using PIP Basic Connections Cable TV Signal Company RF Coaxial Cable 75 Ohm PIP WindowSelecting the PIP Signal Source Input on the back of the TV, youCan press the PIP CHannel DN/UP Buttons to change channels in the PIP windowUsing the PIP Remote Control Buttons Press the PIP ON/OFF button toShow the PIP window again To remove PIP from the screenPress the Cursor Ring Down twice to highlight FEA Adjusting the PIP Color and Tint ControlsPress the Cursor Ring Right to enter the Features Connect the other RF coaxial Using Connection OptionsConnect a cable TV signal to a Use another RF coaxial cable to Connect two RF coaxial cables toCable to the INput on the cable box Helpful Hints Glossary of Television Terms Index Factory Service Locations CanadaHouston Limited Warranty Projection Television