Philips 55P 8341, 64P8341, 64P8342, 50P8342 Clearing ALL Blocked Channels, Right again to highlight

Page 29

Features Menu • The AutoLock Control

CLEARING ALL BLOCKED CHANNELS

The CLEAR ALL control will allow you to remove all channel

blocks that have been turned on through the BLOCK CHANNEL control. To clear all channel blocks, follow the simple steps below.

BEGIN

Press the MENU/SELECT but- ton on the remote control to show the on-screen menu.

Press the CURSOR RING

DOWN twice to highlight FEA-

TURES.

Press the CURSOR RING RIGHT. Then press the CUR- SOR RING DOWN once to high- light the AUTOLOCK control.

Press the CURSOR RING

RIGHT again to highlight

ACCESS CODE.

Enter your four-digit ACCESS CODE.

Press the CURSOR RING DOWN twice to highlight CLEAR ALL.

Press the CURSOR RING RIGHT. The CLEAR ALL option will display the word CLEARED. All blocked channels will then be viewable.

Press the STATUS/EXIT but- ton to remove the menu.

SMART HELP

This control clears only the blocks placed on channels

through use of the BLOCK CHANNEL control and will not turn off the MOVIE RATING, TV RATING, BLOCK UNRATED, or NO RATING control settings.

	PICTURE		TIMER
	SOUND		AUTOLOCK
	FEATURES		PIP		FEATURES
	INSTALL		CLOSED CAP		FEATURES
	INSTALL		CLOSED CAP		TIMER		TIME
					TIMER		TIME
					AUTOLOCK		START TIME
					PIP		STOP TIME
					CLOSED CAP		CHANNEL
							TUNER MODE
					FEATURES
			POWER		TIMER		ACCESS CODE
					AUTOLOCK		- - - -
					PIP
					CLOSED CAP
	TV	VCR	ACC		7
	SWAP	PIP CH	SOURCE FREEZE	4	7
	DN	UP		4	FEATURES
	SOUND		PICTURE	3		TIMER		ACCESS CODE
						AUTOLOCK		- - - -
8						PIP
8	STATUS/		MENU/			CLOSED CAP
	EXIT		SELECT			CLOSED CAP
		MUTE		1
	VOL		CH	1
	VOL		CH
	3		2
	3		3
	6		3		FEATURES
					FEATURES
						TIMER		ACCESS CODE
	4	5	6			TIMER		ACCESS CODE
	4	5	6			AUTOLOCK		X X X X
						AUTOLOCK		X X X X
	7	8	9	5		PIP
	TV/VCR	0		5		CLOSED CAP
	A/CH	0	SURF
	POSITION		PIP
					FEATURES
					AUTOLOCK
					BLOCK CHANNEL			AV2
					SETUP CODE			AV3
					CLEAR ALL			ALL
					MOVIE RATING			1
					TV RATING			2

FEATURES			FEATURES
AUTOLOCK				AUTOLOCK
	BLOCK CHANNEL				BLOCK CHANNEL
	SETUP CODE				SETUP CODE
	CLEAR ALL				CLEAR ALL	CLEARED
	MOVIE RATING				MOVIE RATING
	TV RATING				TV RATING
	BLOCK OPTIONS				BLOCK OPTIONS

29

Image 29

Contents Projection Television Warranty Verification Important Safety Instructions Table of Contents Digital-Ready Projection TV FeaturesPress the Cursor Ring Right Adjusting the PictureScreen menu Turning on the Dynamic Noise Reduction DNR Control Press the Cursor Ring Right or Left to switch DNR onPress the MENU/SELECT but Press the STATUS/EXIT buttonRight or LEFTto switch between on and OFF Ton on the remote control to show the on-screen menuTurning on the Imagemax Control Press the Cursor RingConverge RED/BLUE Down repeatedly until MULTI- Point RED is selected Right to enter Navigate modeConverge Multipoint RED/BLUE Menu Press the MENU/SELECT but Ton to return to the ConvergenceMultipoint RED Save MultipointUndo Multipoint Undo MultipointDown repeatedly until Undo Multipoint is selected Press the Cursor Ring Down Setting the ClockPress the MENU/SELECT button Right to enter the Features menu Setting the Start TimeRight again to highlight the time indicator area Down twice to highlight FEARight to highlight the time indica- tor area Setting the Stop TimeHighlight the Stop Time control Press the Cursor Ring RIGHT. Then press the Cursor Selecting the ChannelPress the Number buttons to Enter the desired start-up channel. OrSelecting the Tuner Tuner ModePress the Cursor Ring Right again. Then press the CUR Setting the Activate ControlONCE, press the Cursor Ring Cursor Ring Right againConstantly Displaying the Time on Screen Right or Left to turn the Timer Display on or OFFMovie Ratings Understanding AutolockPress the Cursor Ring Right to highlight Access Setting UP the Access CodeEnter a new four-digit code Enter your new four-digit codePress the Cursor Ring UP or Enter your four-digit AccessBlocking Channels Enter your four-digit Access CODE. Correct will flash very Right again to highlight AccessBlocking by Movie Rating Down repeatedly until Movie Rating is highlightedRight to enter the TV Rating menu Blocking by TV RatingING is highlighted Turning the Blocking Control on or OFF Enter your four-digit Access Code Press the Cursor RingDown once to select Block Blocking Unrated BroadcastsRight to enter the Block Options menu Blocking Broadcasts That have no Rating Right again to highlight Access Code input areaDown twice to highlight no RAT- ING Press the Cursor Ring Right or Left to turn no RATPress the STATUS/EXIT but Reviewing Your SettingsSTATUS/EXIT button to remove Them from the screenRight again to highlight Clearing ALL Blocked ChannelsDown to select a Caption Mode Using the Closed Captioning ControlDown repeatedly until the Closed CAP control is highlighted SOR Ring Right again to highTrol, press the Cursor Ring Adjusting the TREBLE, BASS, and BalanceThen Press the Cursor Ring Right or Left to adjust On or OFF Using the AVL Audio Volume Leveler ControlDown repeatedly until AVL is high Mono Using Incredible SurroundDown once to highlight Sound menu Setting the TV for Stereo and SAPSound TrebleDown repeatedly until Audio OUT is highlighted Setting the Audio OUT ControlPress the Cursor Ring Left Or Right to set the Audio OUT to Variable or FixedTon to remove the menu from the screen Using the TV Speaker Control and Audio OutputsTo hear the TV sound from only the audio system speakers Using the Bass Boost Control Press the Picture button Using AutopicturePress the Picture button on Press the Sound button on the remote control. The current Using AutosoundAutoSound setting will appear in the middle of the screen AutoSound ChoicesSurf Using SURF, Alternate CHANNEL, and Program ListSleep Using the Sleep Timer ControlSleep OFF Press the VOLume +,- but Using the Volume ButtonsTons to adjust the TV’s sound level VolumeCV1 TUNER-B TUNER-A Using the AV ButtonDoes the remote turn the accessory device on? Setting the TV Remote to Work Accessory DevicesDesired accessory device and press the Power button Please read through all the steps before beginning Ry device and continue holding the buttons down Search MethodSee the next page for more codes Setting the TV Remote to Work AccessoriesSatellite Receiver Brand Remote Codes Cable TV Signal Company RF Coaxial Cable 75 Ohm PIP Window Using PIP Basic ConnectionsInput on the back of the TV, you Selecting the PIP Signal SourceCan press the PIP CHannel DN/UP Buttons to change channels in the PIP windowPress the PIP ON/OFF button to Using the PIP Remote Control ButtonsShow the PIP window again To remove PIP from the screenPress the Cursor Ring Down twice to highlight FEA Adjusting the PIP Color and Tint ControlsPress the Cursor Ring Right to enter the Features Connect the other RF coaxial Using Connection OptionsConnect a cable TV signal to a Use another RF coaxial cable to Connect two RF coaxial cables toCable to the INput on the cable box Helpful Hints Glossary of Television Terms Index Canada Factory Service LocationsHouston Projection Television Limited Warranty