Philips VRX242AT owner manual Setting Up the VCR Plus+ Programming System cont’d

Page 33

VRX240comb 4/8/99 8:45 PM Page 33

Setting Up the VCR Plus+ Programming System (cont’d) 33

2

Now, compare the channel numbers you have written in the VCR PLUS+ CH. and CABLE/TV CH. columns. For stations whose VCR Plus+ and Cable/TV channels do not match, you must tell the VCR the VCR Plus+ and Cable/TV channel numbers by following steps 3 - 7. Make each entry within 60 seconds of the previous entry.

2 Examine the lists on page 32.

4-6

3

Press the MENU button.

4

Press the PLAY/o button or the STOP/p button to select VCR SET UP, then press the F.FWD/B button.

SELECT op CHOOSE B

→ REPEAT PLAY OFF

ON SCREEN MODE LANGUAGE

VCR PLUS+ REF. MAP

TO END PUSH EXIT

5

Press the PLAY/o button or the STOP/p button to select VCR PLUS+ REF. MAP, then press the F.FWD/B button.

VCR PLUS+ CROSS REF. MAP

VCR PLUS+

CABLE/TV

9898

9999

1 – – – – –> 1

22

TO SELECT CH PUSH op

THEN ENTER CH NO. TO END PUSH EXIT

6

Look at the lists you filled in on page 32. For stations whose

VCR Plus+ and Cable/TV channels do not match, press the PLAY/o button or the STOP/p button until the arrow is beside the VCR Plus+ channel you need. Then, press the Number buttons to enter the corresponding Cable/TV channel from your list. (Enter a “0” before single- digit channels.) Enter all the stations on your list.

Note: If you are using a Cable Box/DBS, the Cable/TV channel will be 03 or 04 (the Cable Box/DBS output channel) for every VCR Plus+ channel. You must set the Cable Box/DBS to the channel you want to record; leave the Cable Box/DBS on for the timer recording.

VCR PLUS+ CROSS REF. MAP

VCR PLUS+

CABLE/TV

9898

9999

1– – – – –> 23

22

TO SELECT CH PUSH op

THEN ENTER CH NO.

TO END PUSH EXIT

7

Press the STATUS/EXIT button.

 

POWER

 

VCR/TV

EJECT

6

1

2

3

 

4

5

6

 

7

8

9

CHANNEL

7

VCR PLUS+

0

+100

 

SPEED

TIME SEARCH

MEMORY

3

MENU

STATUS/EXIT

CLEAR

SLOW

REWIND

/PLAY

F.FWD

 

REC/OTR

/STOP

PAUSE/STILL

Helpful Hints

•To erase a Cable/TV channel num- ber, repeat steps 3-5 on this page. Then, press the PLAY/o button or the STOP/p button to select it.

Press the CLEAR button, then press the STATUS/EXIT button.

•To select line input for the Cable/TV channel, press 0,0. AUX will appear on-screen.

•When you receive the VCR, all the VCR Plus+ channel numbers and Cable/TV channel numbers are the same.

Page 32 Page 34
Image 33
Page 32 Page 34
Contents VRX240AT For Customer Use Dear Philips Magnavox product ownerFeatures Safety PrecautionsIntroduction Table of Contents Before Using Your VCR Disconnect the antenna or cable from your TV Hookups Without a Cable Box / Direct Broadcast SystemANT Audio OUT Plug in the TV and the VCRHookups With a Cable Box / Direct Broadcast System ConnectionsRecording/Viewing Any Channel Recording One Channel/Watching Another Hookups With a Cable Box / Direct Broadcast System cont’dHookups With a Stereo TV Turning on Your VCR Press the Menu button Automatic Channel SetupAdding/Deleting Channels Automatic Channel Setup cont’dPress the STATUS/EXIT button once or twice to exit Reviewing Memorized ChannelsSetting the Clock Daylight-Saving Time Language Selection Remote Control Buttons Power ButtonMenu Button Remote Control Buttons cont’d Eject ButtonFWDFast Forward/B Button Status Display example only On-Screen Status DisplaysIf you select Status ON, then select Counter only on If you select Status ON, then select Counter only OFFVCR Display Panel Front Panel Rear Panel 1Turn on the TV 2Insert a tape in the VCR PlayingVCR light does not appear, press the VCR/TV button once RecordingRecording One Channel/Watching Another Remote control to select channel 03 or 04 at the TVTo return to the channel being recorded, use the TV Press the VCR/TV button to put the VCR in VCR posiOne-Touch Recording Daily Timer RecordingInstructions continue on Timer Recording cont’dTape Speeds Press the STATUS/EXIT button. Program WAS COMPress the PLAY/o button or the STOP/p button to select Checking or Cancelling Timer RecordingsProgram REVIEW, then press the F.FWD/B button See page 42 for more hintsChannels Setting Up the VCR Plus+ Programming SystemSetting Up the VCR Plus+ Programming System cont’d Timer Recording With the VCR Plus+ Programming System Timer Recording With the VCR Plus+ Programming System cont’d Antenna Rerecording Tape DuplicationPress the F.FWD/B button so that on appears beside Repeat PlayPress the Time Search button Time SearchReal-Time Counter Memory Forward and Reverse Searching SP/LP/SLP Special Effects PlaybackSuper High Speed Searching LP/SLP Viewing a Still PictureAutomatic Operation Features Helpful Hints Helpful Hints cont’d Cable Box/DBS Output Channel 03 or GlossarySpecifications Video Cassette Recorder Limited WarrantyAutomatic IndexSupplied Accessories
Top Page Image Contents