JVC DM-JV600U manual Safety Precautions

Page 3

SAFETY PRECAUTIONS

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

ATTENTION

RISQUE D’ELECTROCUTION

NE PAS OUVRIR

ATTENTION: POUR EVITER TOUT RISQUE D’ELECTROCUTION

NE PAS OUVRIR LE BOITER.

AUCUNE PIECE INTERIEURE N’EST

A REGLER PAR L’UTILISATEUR.

SE REFERER A UN AGENT QUALIFIE EN CAS DE PROBLEME.

Le symbole de l’éclair à l’intérieur d’un triangle équilatéral est destiné à alerter l’utilisateur sur la présence d’une “tension dangereuse” non isolée dans le boîtier du produit. Cette tension est suffisante pour provoquer l’électrocution de personnes.

Le point d’exclamation à l’intérieur d’un triangle équilatéral est destiné à alerter l’utilisateur sur la présence d’opérations d’entretien importantes au sujet desquelles des renseignements se trouvent dans le manuel d’instructions.

*Ces symboles ne sont utilisés qu’aux Etats-Unis.

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

This unit should be used with 120 V AC only.

CAUTION:

To prevent electric shocks and fire hazards, DO NOT use any other power source.

NOTE:

The rating plate (serial number plate) is on the rear of the unit.

INFORMATION for USA

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

CAUTION

CHANGES OR MODIFICATIONS NOT APPROVED BY JVC COULD VOID USER’S AUTHORITY TO OPERATE THE EQUIPMENT.

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND

(2)THIS DEVICE MUST ACCEPT ANY INTERFER- ENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.

INFORMATION for Canada

This Class A digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations. Cet appareil numérique de la classe A respecte toutes les exigences du Reglement sur le matériel brouilleur de Canada.

AVERTISSEMENT:

POUR EVITER LES RISQUES D’INCENDIE OU D’ELECTROCUTION, NE PAS EXPOSER L’APPAREIL A L’HUMIDITE OU A LA PLUIE.

Ce magnétoscope ne doit être utilisé que sur du courant alternatif en 120 V.

ATTENTION:

Afin d’éviter tout resque d’incendie ou d’électrocution, ne pas utiliser d’autres sources d’alimentation électrique.

REMARQUE:

La plaque d’identification (numéro de série) se trouve sur le panneau arrière de l’appareil.

WARNING:

The battery used in the DM-JV600U must be replaced by a JVC authorized service dealer only.

CAUTION

Use of controls or adjustments or performance of proce- dures other than those specified herein may result in haz- ardous radiation exposure.

Note

Place a cover on the terminal not in use.

Static may cause a malfunction or failure of the unit.

3

Image 3
Contents DM-JV600U Important Safeguards Safety Precautions Encoded to MPEG-2ISO/IEC13818-2 Main FeaturesTable of Contents Precautions Front Panel About DisplayNames and Functions Rear Panel Preparation ConnectingMounting to a Rack Menu setting Menu Flow ChartConfiguration Menu Menu SettingMpeg  ON OFF Press the ESC button How to Change Menu SettingPress the Enter button Press the 8 / 9 buttonsBasic operation Restoring the Default Menu Setting ValuePress the ESC button Press the Enter button Display Flow ChartStarting the Encoding Start the encoding automaticallyStart the encoding manually Operation Stop the encoding manuallyBasic Checking Operation Status Checking Error Log Press the 8 / 9/ / Buttons Using the Administration MenuAdministration menu Error Log Error codeDisplay Others Setting the 3-2 Pulldown Pulldown auto settingEncoding image film material Input signal Output signal Video encoding Audio encoding SpecificationsDM-JV600U Hdtv Encoder