Panasonic EP30006 operating instructions Attaching the control panel stand covers

Page 13

3 Attaching the control panel stand to the right or left side panel of the unit

(Diagram shows attachment to right armrest.)

1.Insert the attachment screw into the lower hole first

The position of the control panel when seated can be

and then tighten lightly by hand.

selected by choosing the appropriate hole for the screw.

 

2.Securing the stand with the attachment screws.

Near

Approx.

Tighten the two screws for the remaining two holes

 

20˚

lightly by hand and then tighten firmly with the allen key.

 

 

Far

 

 

Control panel stand

 

 

 

2

 

 

1 Insert the attachment

 

 

 

screw in either hole and

 

To attach the control panel stand using the attachment

then tighten.

 

Attachment screw

Allen key

screws, tighten the screws level with the holes as

shown in the figure below.

 

 

 

 

Use this screw

 

If the screws are tightened at an angle, the hole may

 

become deformed and the screws may become stuck in

Attachment Screw (M6 × 16)

 

 

the middle.

 

 

 

Control panel

 

 

 

× 3

 

Control panel stand

stand

 

 

 

Hole

Attachment screw

Attachment

 

Hole

screw

 

Allen key

Allen key

 

 

 

Tighten the screws

Do not tighten the

 

screw at an angle

 

level with the holes.

 

with the hole.

 

 

4 Attaching the control panel stand covers

(On both the right and left sides)

The method for attaching the covers is the same for both sides. The diagram shows the side where the control panel stand is attached.

Cover for Side WITH

Cover for Side WITHOUT

Control Panel Stand

Control Panel Stand

1.Insert the top tabs on the cover into the bottom notches on the armrest.

Notches

2.Insert the bottom tabs into the notches on the armrest.

Bottom tabs

 

Control panel

 

stand cover

Top tabs

Notches

Push the cover until you hear it click.

12

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Operating Instructions Instrucciones de Uso Important Safety Instructions Safety Precautions Operating Precautions Grounding Instructions Main unit Part names and functionsBack Control Panel Self-Program Setting Display Voice Guidance Volume DisplayTime Remaining Display During massage Ultra Knead/Repeat DisplayWhere to use the unit Setting up the massage loungerRemoving everything from the box and installing the unit To put the unit down on the floorWidth Approx 68 cm Height Approx 66 cm Length Approx 160 cm AccessoriesConnecting the air plugs AssemblyAttachingarmrests Attaching the control panel stand covers Configuration When removing the control panel stand coverRaising the backrest to the upright position Gap Flat-tip ScrewdriverPlacing the control panel into the control panel stand Attaching the pillow Inserting the shoulder plateShoulder plate Pocket Attach the pillow to the velcro fastenersSwitching on the power supply Check the power cord and the power plugBefore sitting down Check the unitWhen the massage heads are not in the retracted position Pre-Program and Quick Massage Characteristics Upper Body Press the button to turn on the powerProgram Massages Press one of the flashing buttons To select ProgramBody scanning will commence when the program is selected During a massage When the massage startsOverview of the Pre-Program and Quick Massage Upper Body Open the right cover and press the button Creating Self-ProgramsSelf-Program Self-ProgramPress the button to start the program Setting the Time and IntensityTo change the time and intensity in the middle of a massage Massage SequenceManual Operation Manual Selection MassagesManual Operation Select the massage action Select the location you want to massagePress Button to start the action Body scanning for Manual OperationUltra Knead Shiatsu Swedish For additional operationsAdjusting the speed Adjustments During a MassageChanging the program Changing the massage styleAdjusting the position Adjusting the intensityAdjustment of range of intensity Width Adjustment LimitsDetails about the massage style Range that can be massaged on the upper bodyOpen the left cover Adjusting the intensityTo execute the air massage only Adjust the legrest so that your feet fit snugly Adjusting the Legrest lengthFor the foot reflexology plate Arm Massage How to use the hand/arm massageInsert the hand all the way inside Center of the armrest Adjustments for the seat/thigh massage Adjustments for the Shoulder MassageOuter Shoulder Massage Operations of the leg stretch Using the stretch massageOperations of the arm stretch To execute the stretch massage onlyOttoman and Backrest height adjustment Legrest slide lever Press Button to adjust the volume Adjusting the voice guidance volumePress the button to shift the volume level by one up/down Adjusting the control panel stand Adjusting the control panel stand and pillowAdjusting the pillow for correct height during a massage When the selected button starts flashing quickly Saving the user program settingsPress the button used to save your settings Advanced user memory functionFor Pre-Program, Quick Massage, and Self-Program Settings that can be savedFor Manual Operation Erasing saved data Press the button to turn on the power After completing the massage When the massage is completeEmergency Stop Press the button Keep the lock switch key out of reach of children Disconnecting the powerAreas covered with synthetic leather Cleaning and MaintenanceWipe these areas with a soft, dry cloth Lifting the Unit Moving the UnitDo not move the unit while someone is seated in it Using the wheels to move the unit Massage heads stop during operation Problem Cause and Remedy Motor NoisesMassage heads do not come up to the shoulder or NeckSometimes the power won’t turn on when Is pressed Problem Cause and Remedy Unit will not operate at allAgain when a massage has finished Power cord or power plug is abnormally hotPanasonic Consumer Electronics Company
Top Page Image Contents