Britax 85 SICT manual Latch Short Path, Checklist

Page 13

Installing the Child Seat: Harness Mode

LATCH – Short Path

Before you begin:

99Check that your vehicle has LATCH anchors.

*Check your vehicle owner’s manual for the vehicle’s LATCH anchor limits.

99Check that your vehicle has a top tether anchor.

*Britax recommends that the Versa-Tether is used at all times. Using the tether will improve the stability of the child seat and reduce the risk of injury. Check your vehicle owner’s manual for tether anchor locations.

99Remove the Versa-Tether®hook from the storage clip and place it over the child seat back to keep it from becoming pinned between the child seat and vehicle seat during installation.

Versa-Tether

(Top Tether)

Install with LATCH using only the short belt path as shown above.

Installing the Child Seat: Harness Mode

1 Locate the LATCH anchors in your vehicle.

* Ensure harness height is

 

adjusted to fit your child.

2

 

2 Rotate the positioning block to

the front and place the child 1 seat on the vehicle seat.

3Verify that the LATCH strap is

not twisted and firmly press the LATCH connectors onto their adjacent LATCH anchors to attach.

4 Push the child seat into the vehicle seat and pull the end of the LATCH strap through the belt slot to secure.

* The child seat is secure when it cannot be moved front-to-back or side-to-side more than 1 in.

(2.5 cm) at the belt path. If the child seat is not secure, repeat the installation procedure or use a different seating location.

5

Firmly press the Versa-Tether®

 

 

hook to the vehicle tether

OR

 

anchor to attach. Remove all

 

 

 

slack from the tether webbing.

 

6

Use the elastic strap to

OR

 

contain extra webbing.

 

Checklist

99Check that positioning block is rotated to the front.

99Check all connections and verify that child seat is secure.

*The child seat is secure when it cannot be moved front-to- back or side-to-side more than 1 in. (2.5 cm) at the belt path. If the child seat is not secure, repeat the installation procedure or use a different seating location.

99Ensure any excess Versa-Tether®webbing is stored in elastic band. Always ensure any excess webbing is contained within your vehicle.

22

23

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Frontier 85 Sict Table of Contents Certification Important NotesRegistration Child Seat Features Booster Mode Harness ModeWebbing Compatible Vehicle Seat Belts Lap-Shoulder 3-Point BeltIncompatible Vehicle Seat Belts Lap BeltVehicle Buckle Positions Vehicle Seating Positions Harness Mode Harness Height AdjustmentAdjusting Buckle Position Removing the Buckle Booster Mode Head Restraint AdjustmentRe-threading the Buckle Using Lower Anchors and Tethers for Children Latch Using the Chest ClipUsing the Positioning Block Fastening the Buckle Releasing the BuckleUsing the Versa-Tether Using the Latch ConnectorsTo remove the Versa-Tether from the storage clip General Information Booster mode with children whoLatch Short Path ChecklistLap-Shoulder Belt Selecting a Belt Path Short lap-shoulder belt path installationLap-Shoulder Belt Short Path Lap-Shoulder Belt Long Path Long lap-shoulder belt path installationLap Belt Short Path Harness to Booster Mode To remove the harness and buckle Switching Between ModesTurn and slide the retainer through the slot to remove Booster to Harness Mode To replace the harness and bucklePositioning the Child Seat Booster Mode Lap-Shoulder Belt Using LatchChild seat in harness mode Remove slack from the vehicle belt Cover Removal Cleaning the Harness Cleaning the CoverCleaning the Shell Cleaning the Side Impact CushionsTo Clean Cleaning the BuckleBuckle Replacement Buckle RemovalEnergy-Absorbing Tether TroubleshootingLimited ONE-YEAR Warranty Page Britax Child Safety, Inc
Top Page Image Contents