Britax 50 manual Child Seat Cover Removal, Remove the entire cover from child seat

Page 22

Securing Your Child

7Gently pull up on the harness straps to tighten the lap section of the harness, which should fit low on the child’s body.

8Slowly pull the adjuster strap to tighten the harness around the child (Fig. B).

NOTE: Pull the harness adjuster strap away from the child seat (parallel to the ground) to tighten. Do not B pull at a sideways angle (see diagrams below).

Care and Maintenance

Child Seat Cover Removal

WARNING! Do not take apart the harness. Never remove the buckle tongues from the harness. They cannot be reattached after removal. If assembled incorrectly, the child seat may not perform as intended.

C

9Position the chest clip at the middle of the child’s chest, level with the armpits (Fig. C).

10Verify that harness is not twisted and child is properly secured.

IMPORTANT:

•Always pull on the harness after securing the child to ensure the buckle tongues are secure in the harness buckle. If the buckle will not fasten with an audible click after inserting each buckle tongue, the harness buckle or adjuster area may be clogged with food, drink or other debris that must be removed. See page 44 for cleaning instructions.

•Adjust the belts provided with this child seat so they fit snugly around your child. A snug strap should not allow any slack. It lies in a relatively straight line without sagging. It does not press on the child’s flesh or push the child’s body into an unnatural position.

1Loosen the harness by lifting the harness adjuster lever while pulling the shoulder straps forward as far as possible.

2Unhook the shoulder straps from the harness yoke on rear of child seat (Fig. D).

3Pull the upper harness straps through the shell and cover to the front of child seat.

4Remove the upper portion of the cover. Be careful not to damage the energy-absorbing foam.

5Remove the buckle and belly pad by turning the metal buckle strap retainer of the buckle on the underside of the child seat so the short side will slide through the child seat shell (Fig. E).

6Push the retainer through the slots in the shell and cover to the top of the child seat.

7Pull the lower harness straps, buckle tongues, and chest clip through lower slots in cover.

8Remove the entire cover from child seat.

D

E

For additional demonstration please visit www.BritaxUSA.com.

Refitting the Cover: To re-fit the cover, reverse the previous directions. Make sure the shoulder straps are properly threaded through the chest clips

and the harness is not twisted.

40

41

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Roundabout Table of Contents If the following are not observed Death or Serious Injury can OccurRegistration Important NotesCertification Serial Number Batch Number Date of ManufactureForward-Facing Important Harness AdjustmentsRear-Facing Rear-FacingChild Seat Features Compatible Vehicle Seat Belts Lap-Shoulder 3-Point Belt Switchable Retractor in ALR with Sliding Latch PlateELR Emergency Locking Retractor with Locking Latch Plate ALR Automatic Locking Retractor Lap BeltLocking Latch Plate Vehicle Buckle Positions Incompatible Vehicle BeltsVehicle Seating Positions Latch Installation Figure a illustrates a rear-facing Latch installationLap-Shoulder Belt Installation Lap-Belt Installation Installation Forward-Facing Lap-Shoulder Belt Installation IMPORTANTb Safety Information Rear-Facing InstallationForward-Facing Installation For forward-facing aircraft installation FigApproved tether anchorage locations Using the Versa-TetherTether Connector Strap That the child seat is properly securedHas released on either side, the child seat is no Switching the Latch ModeEnergy-Absorbing Versa-Tether Child seatRecline Adjustment Using the Locking ClipAdjacent slots Harness Buckle Adjusting Harness Slot HeightChest Clip Releasing the Chest Clip SqueezeAdjusting Harness Buckle Position Instructions on pages 26Child Seat Cover Removal Remove the entire cover from child seatCleaning the Harness Cleaning the CoverCleaning the Shell Cleaning the Harness BuckleWarranty Double Check Every Time YOU USE this CAR Seat

50 specifications

The Britax 50 is a leading vehicle safety seat designed to ensure the utmost protection for young passengers. Renowned for its comprehensive safety features, the Britax 50 stands out in a crowded market, delivering top-notch security and comfort.

One of the key features of the Britax 50 is its innovative SafeCell Impact Protection system. This technology includes a series of components designed to work in harmony to provide enhanced protection during a collision. The SafeCell base is engineered to compress and lower the center of gravity, which helps to reduce the risk of injury. Additionally, the integrated crumple zones absorb crash forces, further safeguarding your child.

Another notable characteristic of the Britax 50 is its unique head safety technologies. The Advocate model specifically features a versatile headrest, which provides superior side impact protection. The headrest can easily adjust to accommodate your child's growth while maintaining an optimal position to shield their head and neck during any impact.

Comfort doesn’t take a backseat with the Britax 50. The seat is equipped with plush padding and premium fabrics designed for both softness and durability. The seat’s design is also tailored to offer ample legroom, ensuring that children remain comfortable during long travels. The easy-to-remove cover allows for hassle-free cleaning, which is a significant advantage for parents managing spills and messes.

Installation of the Britax 50 is simplified through its User-Friendly Belt-Guide System. Parents can easily secure the seat in various vehicles without confusion. The ClickTight Installation feature is a standout, providing a clear and reliable way to ensure the seat is properly mounted using the vehicle seat belt.

The Britax 50 also comes with multiple recline positions, providing maximum comfort for infants and toddlers alike. The seat can be configured to various angles, ensuring optimal safety and comfort as your child grows.

In summary, the Britax 50 combines cutting-edge safety technologies, comfort, and user-friendly features, establishing itself as a solid choice for parents prioritizing their child’s wellbeing on the road. With its reputation for excellence and commitment to safety, the Britax 50 is more than just a car seat; it represents peace of mind for families everywhere.
Top Page Image Contents