Graco ISPC054BA manual FORWARD-FACING Installation with Latch

Page 12

FORWARD-FACING INSTALLATION WITH LATCH

1LATCH belt must be routed through opening in child restraint for forward-facing(see page 23, fig. l).

Belt must lay flat and not be twisted.

2Adjust child restraint to upright position (see pages 18 and 19, fig. b) and place forward-facingon vehicle seat equipped with LATCH anchors.

3For ease of installation, extend LATCH belt to its maximum length.

4Hook connectors to vehicle lower anchors (fig. a). Pull connectors to be sure they are securely attached (fig. b).

5Press down firmly in center of child restraint to compress vehicle seat cushion while tightening LATCH belt by pulling adjustment belt (fig. c). Use your knee to press down in center of child restraint (fig. c).

6Pull front to back and left to right to check for secure installation (fig. d).

Check that the lower anchorage belt stays tight and does not slip from the tightened position. If it does not stay tight, try another seating position or contact Customer Service (see back cover).

7Attach tether strap hook (A) to anchor hardware (B) and tighten adjustment belt to remove any slack (fig. e).

Periodically check that child restraint is securely installed; adjust if necessary.

10

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Page Table of Contents Safety First Check List Important InformationRegistration Information Page Page Basic Information CertificationVehicle Seat Protection What is LATCH? Latch System for VehiclesVehicle Lower Anchor Points Vehicle Seat CreaseLatch System Fig. a Child Restraint Lower Anchorage BeltHeight & Weight Limits Outgrowing Child RestraintRear-facing 5 to 30 lbs .2-13.6 kg Forward-facing 20 to 40 lbs to 18 kgREAR-FACINGINSTALLATION with Latch Fig. e Fig. dFORWARD-FACING Installation with Latch FORWARD-FACING Installation with Latch Tether Openings Pull to tightenREAR-FACING Installation with Vehicle Seat Belts Lap/shoulder belt FORWARD-FACING Installation with Vehicle Seat Belts FORWARD-FACING Installation with Vehicle Seat Belts Placing Child in Child Restraint Check harness systemPoint Models Only Overhead Shield Models OnlyPlacing Child in Child Restraint Point Crotch Strap Adjustment fig. c Overhead Shield Adjustment fig. dHarness Straps fig. a Harness TieClip Upright Upper Tab Lower TabRecline Changing Harness Strap Slots Point Models fig. e For Infants or Small ToddlersFor Toddlers Overhead Shield Models fig. fTop Loop Bottom Loop Splitter PlateLatch Belt Routing Latch belt. figFig. k Removing Latch from Vehicle Anchor Points Fig. mLatch storage Fig. q or rVehicle Seat Belts Vehicle Seat Belts Belts Forward of Seat CreaseLap Belts Manually Adjustable Lap Belts With RetractorFlip Passive Restraint Lap Belt with Motorized Shoulder Belt Passive Restraint Lap or Shoulder Belt Mounted on DoorCombination Lap/Shoulder Belt with Sliding Latch Plate Combination Lap/Shoulder Belt with Locking Latch PlatePull Locking Clip Additional Information Tether StorageFor storage of tether hook Tether Hook Back of Child RestraintCup Holder Available on some modelsRemoving Cup Holder Additional Information Care & Cleaning Removing Seat Pad all modelsRemoving Overhead Shield Pad Aircraft Use Seat Pad and Overhead Shield PadHarness Straps and Latch belt Shell and Overhead Shield Cup HolderPage Replacement Parts How to OrderShip to Model No ManufacturedCall US First Manual de instrucciones Tabla DE Contenido Antes de EmpezarUtilización Información especialInformación Importante Información de registroLista de control de seguridad Advertencia Prevenga lesiones graves o la muerte Orientación trasera debe nivelarse Advertencia Información Básica¿QUÉ ES EL LATCH? Sistema Latch para vehículosAnclaje Sistema Latch El sistema LatchAnclaje Superior del Punto de anclaje Superior del Vehículo Asiento de seguridadLímites DE Altura Y Peso Orientados hacia delante de 20 a 40 libras de 9 a 18 kgInstalación Orientada Hacia Atrás CON Latch Anclaje Aperturas Toallas Instalación Orientada Hacia Delante CON Latch Anclaje Aperturas Jale para Apretar Almacene el cinturón Latch vea la página 25, fig. q Guardado Toallas Instalación con cinturón de Seguridad para la cintura / hombroAjústelo si es necesario Fig. d Colocar AL Niño EN EL Asiento DE Seguridad Compruebe el sistema del arnésModelos Operaciones Y Ajustes Clip VerticalReclinada Modelos de 5 puntos fig. e Para bebés o niños pequeños Para niños más grandesModelos con barra protectora fig. f Fig. e Bucle Placa de unión Fig. f SoporteColocación del cinturón Latch Usar el sistema Latch orientado hacia atrás. o Retirar el Latch de los puntos de anclaje del vehículo Almacenaje Latch Abroche el sistema Latch en la barra deBarra de almacenaje Cinturones DE Seguridad DEL Vehículo Cinturones ubicados delante del pliegue del asiento Pliegue del AsientoCinturones de regazo ajustables manualmente Cinturones de regazo con retractorDéle la vuelta No SE Debe usar con ningún asiento Jale Fig. a Déle la vueltaPulgada 1 cm Información Adicional Almacenaje del anclajeGancho del anclaje Parte trasera del asiento de seguridad Portabebidas Disponible en algunos modelosPara quitar el portabebidas PestañaEl cojín del cuerpo Cuidado y limpieza Los ModelosRetirar la almohadilla de la barra protectora Asiento de seguridad para autos de segunda mano Las almohadillas del asiento y de la barra protectoraArmazón y apoyavasos de la barra protectora HebillaNotas Lista DE Piezas Cómo efectuar pedidosEnvíe a De modelo Fabricado enLlámenos Primero

ISPC054BA specifications

The Graco ISPC054BA is a cutting-edge infant car seat designed to provide safety, comfort, and ease of use for both parents and their little ones. With a range of features and technologies, this car seat aims to enhance the traveling experience for families while ensuring the utmost protection for infants.

One of the standout features of the ISPC054BA is its TrueShield Technology, which incorporates advanced side impact protection. This system is designed to absorb and distribute crash forces, thereby reducing the risk of injury in the event of an accident. The car seat also meets or exceeds all safety standards set by the National Highway Traffic Safety Administration (NHTSA), offering parents peace of mind when traveling.

Comfort is another essential characteristic of the ISPC054BA. It boasts a plush infant insert that provides additional support for newborns, ensuring a snug and secure fit. The head support is adjustable, allowing it to grow with the child, while the seat includes a five-point harness that can be easily adjusted to accommodate infants as they grow. The installation process is straightforward, featuring Graco’s InRight LATCH system, which allows for quick and secure installation in vehicles.

In terms of convenience, the ISPC054BA is designed with parents in mind. The car seat features a lightweight design that makes it easy to carry and transfer between vehicles. An ergonomic handle provides comfort during transport, while the built-in canopy offers protection from the sun and rain during outdoor activities.

Another notable characteristic is the versatility of the ISPC054BA. It seamlessly transitions from car to stroller, making it an excellent addition to a travel system. The car seat is compatible with various Graco strollers, allowing parents to create a convenient travel solution without disturbing their sleeping baby.

Maintenance is also a breeze with this model. The car seat cover is removable and machine washable, ensuring that it remains clean and hygienic for everyday use. Parents will appreciate this feature, especially during messy outings.

In conclusion, the Graco ISPC054BA is a reliable infant car seat that combines safety, comfort, and convenience. With its innovative features like TrueShield Technology, easy installation, and compatibility with Graco strollers, it stands out as a top choice for modern families seeking a dependable and user-friendly car seat solution.
Top Page Image Contents