Graco ISPC054BA manual REAR-FACING Installation with Vehicle Seat Belts

Page 14

REAR-FACING INSTALLATION WITH VEHICLE SEAT BELTS

WARNING

LATCH belt MUST be stored when

using vehicle seat belt to install child

restraint.

1Store LATCH see page 25, fig. q.

2Adjust child restraint to recline position (see page 18 and 19, fig. b) and place rear-facingon vehicle seat.

3Thread vehicle seat belt through openings and buckle belt.

4Press down firmly in center of child restraint to compress vehicle seat cushion while tightening vehicle seat belt (fig. a).

5Pull front to back and left to right to check for secure installation (fig. b). Vehicle lap belt MUST stay tight.

If not secure, see “Vehicle Seat Belts” page 26.

6Check level indicator on child restraint.

Vehicle must be on level ground and child in child restraint when checking level indicator.

Ball MUST be entirely in green zone (fig. c). If necessary, place rolled towels under child restraint, at vehicle seat crease, until entire ball is in green zone. Then re-check level indicator.

DO NOT use tether rear-facing. Tether must be stored (see “Tether Storage” page 32).

Periodically check that child restraint is securely installed and properly leveled; adjust if necessary.

12

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Page Table of Contents Registration Information Safety First Check ListImportant Information Page Page Vehicle Seat Protection Basic InformationCertification Vehicle Lower Anchor Points What is LATCH?Latch System for Vehicles Vehicle Seat CreaseLatch System Fig. a Child Restraint Lower Anchorage BeltRear-facing 5 to 30 lbs .2-13.6 kg Height & Weight LimitsOutgrowing Child Restraint Forward-facing 20 to 40 lbs to 18 kgREAR-FACINGINSTALLATION with Latch Fig. e Fig. dFORWARD-FACING Installation with Latch FORWARD-FACING Installation with Latch Tether Openings Pull to tightenREAR-FACING Installation with Vehicle Seat Belts Lap/shoulder belt FORWARD-FACING Installation with Vehicle Seat Belts FORWARD-FACING Installation with Vehicle Seat Belts Point Models Only Placing Child in Child RestraintCheck harness system Overhead Shield Models OnlyPlacing Child in Child Restraint Harness Straps fig. a Point Crotch Strap Adjustment fig. cOverhead Shield Adjustment fig. d Harness TieRecline Clip Upright Upper TabLower Tab For Toddlers Changing Harness Strap SlotsPoint Models fig. e For Infants or Small Toddlers Overhead Shield Models fig. fTop Loop Bottom Loop Splitter PlateLatch Belt Routing Latch belt. figFig. k Removing Latch from Vehicle Anchor Points Fig. mLatch storage Fig. q or rVehicle Seat Belts Vehicle Seat Belts Belts Forward of Seat CreaseFlip Lap Belts Manually AdjustableLap Belts With Retractor Passive Restraint Lap Belt with Motorized Shoulder Belt Passive Restraint Lap or Shoulder Belt Mounted on DoorPull Combination Lap/Shoulder Belt with Sliding Latch PlateCombination Lap/Shoulder Belt with Locking Latch Plate Locking Clip For storage of tether hook Additional InformationTether Storage Tether Hook Back of Child RestraintRemoving Cup Holder Cup HolderAvailable on some models Additional Information Removing Overhead Shield Pad Care & CleaningRemoving Seat Pad all models Harness Straps and Latch belt Aircraft UseSeat Pad and Overhead Shield Pad Shell and Overhead Shield Cup HolderPage Replacement Parts How to OrderShip to Model No ManufacturedCall US First Manual de instrucciones Utilización Tabla DE ContenidoAntes de Empezar Información especialLista de control de seguridad Información ImportanteInformación de registro Advertencia Prevenga lesiones graves o la muerte Orientación trasera debe nivelarse Advertencia Información BásicaAnclaje ¿QUÉ ES EL LATCH?Sistema Latch para vehículos Anclaje Superior del Sistema LatchEl sistema Latch Punto de anclaje Superior del Vehículo Asiento de seguridadLímites DE Altura Y Peso Orientados hacia delante de 20 a 40 libras de 9 a 18 kgInstalación Orientada Hacia Atrás CON Latch Anclaje Aperturas Toallas Instalación Orientada Hacia Delante CON Latch Anclaje Aperturas Jale para Apretar Almacene el cinturón Latch vea la página 25, fig. q Guardado Toallas Instalación con cinturón de Seguridad para la cintura / hombroAjústelo si es necesario Fig. d Colocar AL Niño EN EL Asiento DE Seguridad Compruebe el sistema del arnésModelos Operaciones Y Ajustes Reclinada ClipVertical Modelos con barra protectora fig. f Modelos de 5 puntos fig. e Para bebés o niños pequeñosPara niños más grandes Fig. e Bucle Placa de unión Fig. f SoporteColocación del cinturón Latch Usar el sistema Latch orientado hacia atrás. o Retirar el Latch de los puntos de anclaje del vehículo Barra de almacenaje Almacenaje LatchAbroche el sistema Latch en la barra de Cinturones DE Seguridad DEL Vehículo Cinturones ubicados delante del pliegue del asiento Pliegue del AsientoDéle la vuelta Cinturones de regazo ajustables manualmenteCinturones de regazo con retractor No SE Debe usar con ningún asiento Jale Fig. a Déle la vueltaPulgada 1 cm Gancho del anclaje Parte trasera del asiento de seguridad Información AdicionalAlmacenaje del anclaje Para quitar el portabebidas PortabebidasDisponible en algunos modelos PestañaEl cojín del cuerpo Retirar la almohadilla de la barra protectora Cuidado y limpiezaLos Modelos Armazón y apoyavasos de la barra protectora Asiento de seguridad para autos de segunda manoLas almohadillas del asiento y de la barra protectora HebillaNotas Lista DE Piezas Cómo efectuar pedidosEnvíe a De modelo Fabricado enLlámenos Primero

ISPC054BA specifications

The Graco ISPC054BA is a cutting-edge infant car seat designed to provide safety, comfort, and ease of use for both parents and their little ones. With a range of features and technologies, this car seat aims to enhance the traveling experience for families while ensuring the utmost protection for infants.

One of the standout features of the ISPC054BA is its TrueShield Technology, which incorporates advanced side impact protection. This system is designed to absorb and distribute crash forces, thereby reducing the risk of injury in the event of an accident. The car seat also meets or exceeds all safety standards set by the National Highway Traffic Safety Administration (NHTSA), offering parents peace of mind when traveling.

Comfort is another essential characteristic of the ISPC054BA. It boasts a plush infant insert that provides additional support for newborns, ensuring a snug and secure fit. The head support is adjustable, allowing it to grow with the child, while the seat includes a five-point harness that can be easily adjusted to accommodate infants as they grow. The installation process is straightforward, featuring Graco’s InRight LATCH system, which allows for quick and secure installation in vehicles.

In terms of convenience, the ISPC054BA is designed with parents in mind. The car seat features a lightweight design that makes it easy to carry and transfer between vehicles. An ergonomic handle provides comfort during transport, while the built-in canopy offers protection from the sun and rain during outdoor activities.

Another notable characteristic is the versatility of the ISPC054BA. It seamlessly transitions from car to stroller, making it an excellent addition to a travel system. The car seat is compatible with various Graco strollers, allowing parents to create a convenient travel solution without disturbing their sleeping baby.

Maintenance is also a breeze with this model. The car seat cover is removable and machine washable, ensuring that it remains clean and hygienic for everyday use. Parents will appreciate this feature, especially during messy outings.

In conclusion, the Graco ISPC054BA is a reliable infant car seat that combines safety, comfort, and convenience. With its innovative features like TrueShield Technology, easy installation, and compatibility with Graco strollers, it stands out as a top choice for modern families seeking a dependable and user-friendly car seat solution.
Top Page Image Contents