Graco ISPC054BA manual Lap Belts Manually Adjustable, Lap Belts With Retractor, Flip

Page 30

VEHICLE SEAT BELTS (continued)

❃LapBelts-ManuallyAdjustable

The locking latch plate on some seat belts may slip and loosen after being buckled on child restraint if positioned at a certain angle. If this happens, flip latch plate over (fig. a) and re-buckle. Test installation again to see if this works. If not, move child restraint to another seating position.

❃LapBelts-WithRetractor

Lap belts with retractors may or may not hold a child restraint securely.

Follow these steps to determine if you have a retractor system that will hold child restraint securely:

a. Pull belt all the way out.

b. Allow belt to retract about 6 inches (15 cm). c. Pull out on belt again.

If belt is locked and you cannot pull the belt out any further, you have an Automatic Locking Retractor which may be used with a child restraint. Remember, when installing a child restraint, pull belt all the way out, buckle belt, and then tighten.

If you can pull the belt out again (Step c above), you have an Emergency Locking Retractor which MUST NOT be used with a child restraint.

Flip

(fig. a)

28

Retractor

Page 29 Page 31
Image 30
Page 29 Page 31
Contents Page Table of Contents Safety First Check List Important InformationRegistration Information Page Page Basic Information CertificationVehicle Seat Protection Vehicle Lower Anchor Points What is LATCH?Latch System for Vehicles Vehicle Seat CreaseLatch System Fig. a Child Restraint Lower Anchorage BeltRear-facing 5 to 30 lbs .2-13.6 kg Height & Weight LimitsOutgrowing Child Restraint Forward-facing 20 to 40 lbs to 18 kgREAR-FACINGINSTALLATION with Latch Fig. e Fig. dFORWARD-FACING Installation with Latch FORWARD-FACING Installation with Latch Tether Openings Pull to tightenREAR-FACING Installation with Vehicle Seat Belts Lap/shoulder belt FORWARD-FACING Installation with Vehicle Seat Belts FORWARD-FACING Installation with Vehicle Seat Belts Point Models Only Placing Child in Child RestraintCheck harness system Overhead Shield Models OnlyPlacing Child in Child Restraint Harness Straps fig. a Point Crotch Strap Adjustment fig. cOverhead Shield Adjustment fig. d Harness TieClip Upright Upper Tab Lower TabRecline For Toddlers Changing Harness Strap SlotsPoint Models fig. e For Infants or Small Toddlers Overhead Shield Models fig. fTop Loop Bottom Loop Splitter PlateLatch Belt Routing Latch belt. figFig. k Removing Latch from Vehicle Anchor Points Fig. mLatch storage Fig. q or rVehicle Seat Belts Vehicle Seat Belts Belts Forward of Seat CreaseLap Belts Manually Adjustable Lap Belts With RetractorFlip Passive Restraint Lap Belt with Motorized Shoulder Belt Passive Restraint Lap or Shoulder Belt Mounted on DoorCombination Lap/Shoulder Belt with Sliding Latch Plate Combination Lap/Shoulder Belt with Locking Latch PlatePull Locking Clip For storage of tether hook Additional InformationTether Storage Tether Hook Back of Child RestraintCup Holder Available on some modelsRemoving Cup Holder Additional Information Care & Cleaning Removing Seat Pad all modelsRemoving Overhead Shield Pad Harness Straps and Latch belt Aircraft UseSeat Pad and Overhead Shield Pad Shell and Overhead Shield Cup HolderPage Replacement Parts How to OrderShip to Model No ManufacturedCall US First Manual de instrucciones Utilización Tabla DE ContenidoAntes de Empezar Información especialInformación Importante Información de registroLista de control de seguridad Advertencia Prevenga lesiones graves o la muerte Orientación trasera debe nivelarse Advertencia Información Básica¿QUÉ ES EL LATCH? Sistema Latch para vehículosAnclaje Anclaje Superior del Sistema LatchEl sistema Latch Punto de anclaje Superior del Vehículo Asiento de seguridadLímites DE Altura Y Peso Orientados hacia delante de 20 a 40 libras de 9 a 18 kgInstalación Orientada Hacia Atrás CON Latch Anclaje Aperturas Toallas Instalación Orientada Hacia Delante CON Latch Anclaje Aperturas Jale para Apretar Almacene el cinturón Latch vea la página 25, fig. q Guardado Toallas Instalación con cinturón de Seguridad para la cintura / hombroAjústelo si es necesario Fig. d Colocar AL Niño EN EL Asiento DE Seguridad Compruebe el sistema del arnésModelos Operaciones Y Ajustes Clip VerticalReclinada Modelos de 5 puntos fig. e Para bebés o niños pequeños Para niños más grandesModelos con barra protectora fig. f Fig. e Bucle Placa de unión Fig. f SoporteColocación del cinturón Latch Usar el sistema Latch orientado hacia atrás. o Retirar el Latch de los puntos de anclaje del vehículo Almacenaje Latch Abroche el sistema Latch en la barra deBarra de almacenaje Cinturones DE Seguridad DEL Vehículo Cinturones ubicados delante del pliegue del asiento Pliegue del AsientoCinturones de regazo ajustables manualmente Cinturones de regazo con retractorDéle la vuelta No SE Debe usar con ningún asiento Jale Fig. a Déle la vueltaPulgada 1 cm Información Adicional Almacenaje del anclajeGancho del anclaje Parte trasera del asiento de seguridad Para quitar el portabebidas PortabebidasDisponible en algunos modelos PestañaEl cojín del cuerpo Cuidado y limpieza Los ModelosRetirar la almohadilla de la barra protectora Armazón y apoyavasos de la barra protectora Asiento de seguridad para autos de segunda manoLas almohadillas del asiento y de la barra protectora HebillaNotas Lista DE Piezas Cómo efectuar pedidosEnvíe a De modelo Fabricado enLlámenos Primero

ISPC054BA specifications

The Graco ISPC054BA is a cutting-edge infant car seat designed to provide safety, comfort, and ease of use for both parents and their little ones. With a range of features and technologies, this car seat aims to enhance the traveling experience for families while ensuring the utmost protection for infants.

One of the standout features of the ISPC054BA is its TrueShield Technology, which incorporates advanced side impact protection. This system is designed to absorb and distribute crash forces, thereby reducing the risk of injury in the event of an accident. The car seat also meets or exceeds all safety standards set by the National Highway Traffic Safety Administration (NHTSA), offering parents peace of mind when traveling.

Comfort is another essential characteristic of the ISPC054BA. It boasts a plush infant insert that provides additional support for newborns, ensuring a snug and secure fit. The head support is adjustable, allowing it to grow with the child, while the seat includes a five-point harness that can be easily adjusted to accommodate infants as they grow. The installation process is straightforward, featuring Graco’s InRight LATCH system, which allows for quick and secure installation in vehicles.

In terms of convenience, the ISPC054BA is designed with parents in mind. The car seat features a lightweight design that makes it easy to carry and transfer between vehicles. An ergonomic handle provides comfort during transport, while the built-in canopy offers protection from the sun and rain during outdoor activities.

Another notable characteristic is the versatility of the ISPC054BA. It seamlessly transitions from car to stroller, making it an excellent addition to a travel system. The car seat is compatible with various Graco strollers, allowing parents to create a convenient travel solution without disturbing their sleeping baby.

Maintenance is also a breeze with this model. The car seat cover is removable and machine washable, ensuring that it remains clean and hygienic for everyday use. Parents will appreciate this feature, especially during messy outings.

In conclusion, the Graco ISPC054BA is a reliable infant car seat that combines safety, comfort, and convenience. With its innovative features like TrueShield Technology, easy installation, and compatibility with Graco strollers, it stands out as a top choice for modern families seeking a dependable and user-friendly car seat solution.
Top Page Image Contents