Allstar Products Group ANSI/UL 325 Vehicle Detector Loop Blanking for Swing Gates, Loop Diagrams

Page 7

B:PREPARING THE SITE

Figure 7: Loop Diagrams

Above ground splices may be used providing the wire is twisted, soldered and moisture sealed. For best long term results, do not use wire nuts anywhere in the loop system. Connect to the Vehicle Detector harness by soldering.

For saw-cut installations, observe the methods recommended in Figure 7, above. The saw-cut must be to a depth of 1.5", clean and with no sharp corners. After placing the wires, it is essential that the wires be held tightly in place by a foam backing prior to pouring the sealant. THIS IS ESPECIALLY IMPORTANT WHEN FREEZING IS LIKELY. No voids should exist that will permit the collection of water that might freeze and push the loop wires out of the slot. The sealant used should not be hard setting and should be suitable for pavement material.

THE WIRE USED FOR THE LOOPS MUST BE HEAT AND WATER RESISTANT, CROSS-LINK POLYETHYLENE INSULATED. TYPE XLPE IS BEST. RHW IS O.K. DO NOT USE ANY PVC INSULATED WIRE. (PVC insulation will absorb moisture that may affect Detector operation.) WIRE SIZE SHOULD BE #16 GA. STRANDED OR LARGER.

104945

VEHICLE DETECTOR LOOP BLANKING FOR SWING GATES

The inside loop for a swing gate installation must be located at least 4 feet outside of the arc of the gate. If it is not, the Vehicle Detector may detect the gate as it moves over the loop and cause the Gate to reopen. If the gate is large and a single leaf, the arc usually requires that the loop be a considerable distance from the closed gate position. This may not be an effective position for the loop. In this case, a “blanking” or “shadow” loop may be used.

When a Shadow Loop is necessary, connect the output of the loop detector to terminal #9 “Shadow Loop” and terminal #16 “Common”. The GS4000 circuitry will recognize a vehicle on the loop and prevent the gate from closing while the vehicle is over the Shadow Loop. When the gate is closing or opening, the GS4000 circuitry will ignore input from this loop as the gate swings over it.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Gate Star WA R N I N G H I G H V O LTA G E Table of ContentsConnections for External Entrapment Prevention Sensors PRE-INSTALLATION NotesPinch Points Entrapment Zone Electric Gate Edge Gate System Design and Installation Safety Check ListDeath Gate System Design InstallationAS the Installer YOU are Responsible for Moving GateConcrete PAD Preparing the SitePlacing the Vehicle Detector Loops Vehicle Detector Loop Blanking for Swing Gates Loop DiagramsOther Voltages and 3 Phase Systems Electrical Power RequirementsService Conduit Tools Required Installing the OperatorPlacing the GS4000 Mechanical Unit Installing the GS4000 ARMElectrical Hook UP Installing the GS4000 Control BOXAdditional Lightning Protection Connecting the AC Wiring Volt InstallationsWiring the Mechanical Unit to the Control BOX Right Hand and Left Hand InstallationBI-PARTING Wiring Accessory Equipment HOOK-UPBi-Parting Installation Limit & Motor Wiring Diagram Four Wire Receivers Wiring Radio Receivers to the Terminal StripWiring a 3-BUTTON Station Vehicle Detector Power Wiring a KEYPAD, Card Reader or Telephone Entry SystemConnecting the Vehicle Detector Wiring Vehicle DetectorsConnecting the Loop Wires Presetting the Motor Overload Sensitivity PotentiometersClose Photo SwitchClose Shadow LoopOPEN/CLOSE Push Button ENABLE/ Disable Patent no ,611,205 Setting the Limit SwitchesSetting the Switch Selectable Options NO-LOAD Test ModeTimer to Close Setting Applying Power to the GS4000Indicator Lamps Final Setting of the Close Timer Starting the Operator Final SettingsPRE Running Checklist Smart Setting Maximum RUN TimerFinal Setting of the Motor Overload Sensitivity Installation Notes for Auxiliary EquipmentTo the Owner/End User of Allstar’s GS4000 Precautions for Pedestrian Traffic or Residential AreasEntrapment Zone Basic Operational GuidePinch Points Entrapment Zone GS4000 Mechanical Unit Exploded View Mechanical Unit Exploded ViewARM KIT & Control BOX Exploded View & Parts Mechanical Unit Parts ListPhysical Drive Technical Specifications

ANSI/UL 325 specifications

Allstar Products Group is a prominent manufacturer in the realm of access control and safety products, and its commitment to quality is evidenced by its compliance with ANSI/UL 325 standards. These standards are essential for ensuring the safety and reliability of automatic gates and their related components, focusing on minimizing risks associated with entrapment and injury.

One of the key features of Allstar's ANSI/UL 325 compliant products is their advanced safety mechanisms. These include integrated sensing technology that detects the presence of objects or obstacles in the path of the gate, effectively preventing accidents. This safety technology often encompasses features such as photo eyes and edge sensors that can immediately halt or reverse the movement of a gate if an obstruction is detected.

Additionally, Allstar’s product range is notable for its robust design and durability. Built to withstand various environmental conditions, these products use high-quality materials that ensure longevity and reliability, meeting the stringent demands of both residential and commercial applications. The designs are also forward-thinking, incorporating user-friendly features that allow for easy installation and maintenance.

Another characteristic that sets Allstar apart is their integration of advanced technologies. Many of their products support smart technology, enabling users to control their gates through mobile applications or remote access systems. This integration allows for convenience and enhanced security, providing real-time alerts and status updates.

Allstar Products Group also emphasizes compliance to facilitate peace of mind for users. All their ANSI/UL 325 certified products undergo rigorous testing procedures to ensure they meet the stringent safety and performance requirements set forth by the American National Standards Institute and Underwriters Laboratories. This adherence to such standards not only assures consumers of reliability but also aligns with the industry’s best practices.

In conclusion, Allstar Products Group’s ANSI/UL 325 compliant products exemplify cutting-edge safety features, robust construction, and advanced technology integration. Their commitment to quality and safety ensures that customers can enjoy the benefits of automatic gate systems with confidence, knowing that they adhere to the highest safety standards in the industry.
Top Page Image Contents