Moxa Technologies RS-422, RS-485 user manual Removing Driver, Baud Rate Settings

Page 49

Software Installation

Due to the limitations of Windows 3.x operating system itself, only up to 9 COM por ts are supported, i.e., COM1 to COM9. Hence, Industio CI-134 with 4 ports or other 4 port non-intelligent boards, maximum 6 ports is supported if the existing standard COM ports (COM1 and COM2) are included.

Removing Driver

The program, Dr iver Removal, in the “MOXA Standard COMM Driver” program group is provided to remove the installed driver from the Windows.

Baud Rate Settings

For those Industio CI-134boards configured as High Speed Spectr um, the real working speed is equal to 8 times of the displayed speed. For example, a port, if set to Normal Speed Spectrum with 38.4 Kbps, will work at 38.4 Kbps for sure; while a port, if set to High Speed Spectrum with shown speed 38.4 Kbps, will actually work at

307.2Kbps (38.4 Kbps¡Ñ8). This is applicable to Moxa-provided utility, such as CONFIG and TTY, existing applications and programming, which are described in later chapter.

Industio CI-134 Series User’s Manual 3-27

Image 49
Contents Mar 1st Edition Industio CI-134 Series User’s ManualCopyright Notice Industio CI-134 Series User’s ManualTrademarks DisclaimerMoxa Internet Services Software Installation Hardware InstallationConnection Cable and Cable Wiring TroubleshootingTable of Contents Troubleshooting Connection Cable and Cable WiringTechnical Reference Introduction Industio The Industrial Multiport Async SolutionOverview Termination Resistors Ready for RS-422/RS-485 Automatic Data Direction Control for RS-485Surge/Isolation Protection Asic Design, Compact SizeIntroduction Quick InstallationOperating System Support Moxa Serial Comm ToolsBroad Applications FeaturesSCO Xenix QNX Check ListInstallation Guide First Thing to Do Interface Settings Hardware Installation0x1C0 Quick Hardware InstallationHow to Do Quick Hardware Installation Hardware Installation with IO-IRQ Utility IO-IRQ Utility and Hardware Configuration 6Industio CI-134 Series User’s Manual Address Port IndexSpeed Nor mal Speed Spectr um High Speed Spectr um Press F10 to save the configuration and exit the utility 10Industio CI-134 Series User’s Manual Windows NT Software InstallationInstalling Driver Software Installation 4Industio CI-134 Series User’s Manual Rx Fifo Trigger Port NumberTx Fifo Size 6Industio CI-134 Series User’s Manual Configuring Board and Port 8Industio CI-134 Series User’s Manual Removing Driver Updating DriverWindows 95/98 Software Installation 12Industio CI-134 Series User’s Manual Rx Fifo Trigger 14Industio CI-134 Series User’s Manual Updating Driver 16Industio CI-134 Series User’s Manual DOS Driver Setup Software Installation 20Industio CI-134 Series User’s Manual Por t number TxD buf size RxD buf size F5 Gr oup edit 22Industio CI-134 Series User’s Manual Unloading Driver Loading DriverWindows Software Installation Configuring Driver Baud Rate Settings 28Industio CI-134 Series User’s Manual Serial Programming Tools PComm InstallationWindows NT and Windows 95/98 PComm Programming Library Diagnostic for Moxa boards onlyUtilities Industio CI-134 Series User’s Manual Terminal Emulator DOS API-232 Library Installing API-232Data Scope 6Industio CI-134 Series User’s Manual Serial Programming Tools Diagnose Utility Windows Comm API Library Win16Existing Applications By RTS Mode For back-compatibility Automatic Data Direction Control Mode RecommendedRS-485 Programming Solution 12Industio CI-134 Series User’s Manual RS-422 Cable Wiring Connection Cable and Cable WiringCI-134 RS-422 Point-to-point RS-422 Broadcasting RS-485 Cable Wiring Impedance Matching and Termination Resistors For RS-422 Mode DB-37 Connector Pin OutsFor RS-485 Mode 6Industio CI-134 Series User’s Manual General Troubleshooting TroubleshootingHardware causes and solutions Software Causes and Solutions Io-ir q Remove the jumper on position JP1 Windows NT system panic blue scr een DOS Technical Reference SpecificationsUart TI550C IO/ Addr ess Device PC I/O Port Address MapProblem Report Form Return Procedure