JAI TS(C)-2030EN, TS(C)-2076EN, TS(C)-1327EN, TS(C)-4032EN manual Installing the Required Software

Page 14

EN Camera Series

2.2.2 (a) Changing the IP Address of the EN Camera Using the EN Setup Software

You can use the EN setup software to change the IP address of the camera. Use the steps below.

1.First, set up your PC's network setting properly so that your PC has the 10.0.0.XX subnet. However, XX must not be 65, because the host PC's IP address cannot be the same as that of the camera. The subnet address must be 255.255.255.0.

2.Next, open the EN setup software. If you are starting this software for the first time, you will be asked to type your password. Your case-sensitive user name and password are as follows:

User name: Administrator

Password: Password

3.Click the "Properties" button. You will see the EN cameras that are in the network.

4.Click the icon of the camera you want to change. Once it is selected, find the "IP address" register and change the IP address of the camera.

5.Right-click on the camera icon and select "Reboot." This option will reboot the camera.

6.The camera will now start up with a new IP address.

2.2.2 (b) Changing the EN Camera IP Address Using the Debug RS-232 Serial/ Power Cable

You can use the debug RS-232 serial/power cable to access the BIOS menu and change the IP address of the camera. To do so, follow the steps below.

1.First set up your hyper terminal as 9600-8-N-l. Start up the camera. You should now see the BIOS start-up code.

2.Type "/" to stop the normal camera boot-up and to start the BIOS test mode.

3.Type "3" to select the "IP address change" setting.

4.Type "1" to select the first network interface, and then "1" again to change the local IP address.

5.Type the IP address you want to change.

6.Type "0" to return to the main menu, and then type "0" to start up the normal boot-up.

2.3Installing the Required Software

The EN setup software is used to change the registers of the camera parameters, display live video images, and sniff hardware/trigger Ethernet from the lane controller. To install the software required for the EN camera, run "Setup.exe" from the CD-ROM. This will guide you through the proper installation. Once the software is loaded on your system, find the "EN Setup" software from the Start menu (Start -> EN Setup -> EN Setup). If you are logging in for the first time, you must enter the following case-sensitive user name and password:

User Name: Administrator

Password: Password

Once you log in as Administrator, you can create a new user and set a custom password. To set the properties of each camera connected to the network, follow the steps below:

1.Click the "Properties" button. The software will automatically find all EN cameras currently on the network.

2.Select the EN camera you want to see in the left window. All accessible registers are displayed in the right window.

3.Click the "Video" button. You can select the cameras in the left window in order to display either a live image, or a triggered image. You can display up to four cameras in a single screen.

4. .Adjust the lens as needed.

 

 

 

14

Getting Started

Page 13 Page 15
Image 14
Page 13 Page 15
Contents EN Camera Series Page Certifications WarrantyDisclaimer EN Camera SeriesMailtrafficsales.americas@jai.com Trafficsales.emea@jai.com Table of Contents OP-IR OP-RED List of Figures List of Figures ViiEN Camera Series Viii List of Figures List of Tables List of TablesEN Camera Series List of Tables Related Documents IntroductionScope of this Manual Key Functions of the EN CameraEN Camera Series Product Description Required Equipment Network SettingsGetting Started Getting StartedInstalling the Required Software Image Capturing Start Up the EN Setup SoftwareTutorial TutorialCamera Properties Live Image Capturing/Focusing Live Image Capturing Measuring Box Position Quad Size Image Button Image Properties FTP Image Transfer EN Camera Series Image TransferADR Automatic Dynamic Range Control Light Sensor ConnectionEN Camera Series Flash Nighttime Light Control EN Camera Series Time Synchronization Static IP Address AssignmentDhcp Client EN Camera Series Maintenance Debug CountersFirmware Upgrade Firmware Names and Descriptions3 RS-232 PowerPC Debug Port EN Camera Series EN Camera Series Updating the EN Application Software Uploading the FirmwareTo Verify Version Numbers for all Firmware Uploading FirmwareUpdating the OS Image Updating the Fpga BitfileUpdating the Lib/Drv File Updating the Camera’s H8 FirmwareUploading Firmware Connectors and Cables Connectors and CablesConnector Pin Configurations 1 12-Pin Connector10/100 BaseT Ethernet Pinout Configuration JAI Inc. Power Cables Power Supplies and Power Cable SetupPower Supplies EN Camera Series RS-232 Communication CableAttaching the Camera Lens Building Your Own Power CableAttaching the Power Cable to the Connector Lens Mount FormatCamera Features Camera FeaturesAsynchronous Reset Progressive ScanningTiming Chart 1 TSC-2030EN Timing Chart 2 TSC-1327EN Timing Chart 3 TSC-4032EN EN Camera Series ADR Automatic Dynamic Range Control Camera ADR Control Related RegistersElectronic Shutter Factory Default Settings of the ADR Shutter Min. and Max EN Exposure TimesGain Table Color EN Camera Video Amplifier Gain ControlGain Table BW EN Camera HDR Mode 4032EN Only Flash/Nighttime Light Control 1 RS-485 External ControlColor Filter Array Color Version EthernetImage Formats TIF FormatTCP Message-Based Image Transfer on the Control Channel UDP Image Transfer on Setup ChannelJpeg Format 10 FTP Factory Default Storage Setup of Image BufferingImage Buffering EN Camera Series NTP Network Time Protocol Frequently Asked Questions and Troubleshooting FAQ and TroubleshootingFAQ and Troubleshooting Problem 11 Light Sensor Connection is Not reliable Problem 12 IO Board Communication ErrorInformation and Support Resources Problem 15 FlashErorr Appears in the Error RegisterProblem 16 Timestamp is Not Set to Current Local Time Appendix SpecificationsEN Camera Series Product Specifications Tables Processor Module Model TS-4032EN/TSC-4032EN Physical Dimensions TSC-2030EN/TSC-2076EN/TSC-1327EN Physical Dimensions TSC-4032ENSpectral Response B/W CCD Spectral Response B/W CCD TS-1327ENSpectral Response B/W Cmos TS-4032EN Spectral Response Color CCD TSC-1327EN IR Cut Filter Response for monochrome cameras Color filter spectrum response of TSC-1327EN OP-RED Configurable Order Options for EN CamerasOP-IR OptionsPage Europe, Middle East & Africa

TS(C)-1327EN, TS(C)-4032EN, TS(C)-2030EN, TS(C)-2076EN specifications

The JAI TS(C) series features a range of advanced cameras designed to meet the diverse needs of industrial imaging applications. Among the models in this series, the TS(C)-2076EN, TS(C)-2030EN, TS(C)-4032EN, and TS(C)-1327EN stand out for their innovative technologies and robust characteristics.

The TS(C)-2076EN is equipped with a 20 megapixel sensor that delivers high-resolution images with exceptional clarity. Utilized primarily in high-performance machines, its compact design ensures easy integration into existing systems. The camera offers a frame rate of up to 60 frames per second, making it suitable for high-speed applications. Furthermore, the TS(C)-2076EN features a global shutter, which eliminates motion blur, ensuring accurate image capture in dynamic environments.

Next in the lineup, the TS(C)-2030EN provides a balanced blend of speed and resolution with its 12 megapixel sensor, allowing for both detailed imaging and high frame rates of up to 120 fps. This model is particularly favored in applications such as 2D and 3D inspections, where quick analysis and precision are critical. The camera’s advanced image processing capabilities enhance performance, while its robust build ensures durability in various industrial settings.

The TS(C)-4032EN has been designed for applications requiring exceptional detail, leveraging a high-resolution 41 megapixel sensor. This model offers an impressive frame rate of 30 fps, making it ideal for capturing intricate details in static subjects. Its large sensor size and advanced optics increase light sensitivity, enabling it to perform well in low-light conditions. The camera also supports advanced connectivity options, facilitating seamless integration with various imaging systems.

Lastly, the TS(C)-1327EN focuses on high-speed imaging with a 3.2 megapixel sensor that can achieve frame rates of up to 300 fps. This camera is specifically engineered for fast-moving objects, making it suitable for applications in areas such as robotics and automation. Its compact design, along with superior synchronization features, make it an excellent choice for synchronized multi-camera setups.

Collectively, the JAI TS(C) series combines high image quality, rapid frame rates, and advanced imaging technologies to deliver versatile solutions for industrial applications. Each model is crafted with precision and built to endure, ensuring they remain reliable tools for meeting modern industrial imaging demands.
Top Page Image Contents