JAI TS(C)-4032EN, TS(C)-2076EN, TS(C)-1327EN, TS(C)-2030EN manual Electronic Shutter

Page 43

EN Camera Series

Shadow factor is used to calculate the contrast of the Light Sensor A Side to the B Side of the light sensor. Based on this Shadow Factor, the camera’s ADR logic optimizes the camera parameters (exposure time, gain, vtop, vbot, pedestal). Please do not change this value and keep the factory default (See EN to LC Interface Document for the factory default).

•ADR Shutter Max

Based on the light sensor reading, the camera’s ADR (Automatic Dynamic Range Control) optimizes the exposure time of the camera, and this setting is the upper limit of the exposure time range. Normally, a monochrome camera is set to 500 usec, as the FlashHead strobes the light only for 500 usec. A color camera can hold a longer exposure time, but keep in mind that the motion blur is severe if the “ADR Shutter Max” is longer than 1 msec. Increase “ADR Shutter Max” if the night image is too dark and you can accept more motion blur.

•ADR Shutter Min

Minimum or shortest exposure time that the camera ADR control will adjust to. Keep this to the factory default (See EN to LC Interface Document for the factory default).

•ADR Debug Side A

This value is read-only when “Camera ADR Control” is set to “ADR Control (using Light Sensor)”. ENSetup software displays the raw reading of the light sensor A Side value. If “Camera ADR Control” is set to “Debug” mode, you can write an A Side value to simulate the camera ADR. See “Camera ADR Control”.

•ADR Debug Side B

See “ADR Debug Side A”. This is for Light Sensor Side B.

•ADR White-to-Blue Ratio

“ADR White to Blue Ratio” is the ratio between a white plate and blue plate, and is used to optimize the camera parameters. This value is optimized by JAI, and should be kept at factory default. Please do not change it.

•Camera Shutter Mode

This is read-only status. Current setting of camera exposure time (dial). To find out Dial vs exposure time (us) relationship, please see Operational Manual.

•Camera Gain

This is read-only status. Current setting of camera gain.

•Camera Vtop

This is read-only status. Current setting of camera ADC Vtop setting. Normally, Vtop is kept to 255. The value is lowered only if the system needs extra gain in night time (Only 9720EN).

•Camera Vbot

This is read-only status. Current setting of camera ADC Vbot setting. Vbot is kept to 0 at night time. The camera’s ADR logic raises Vbot in sunny daytime to increase the contrast of the license plate.

6.3.2Electronic Shutter

Normally, exposure time is controlled automatically by ADR (Automatic Dynamic Range) control algorithm inside the EN, based on the output from light sensor. However during nighttime installations it is often convenient to manually adjust the shutter time to a larger value so that the focusing targets and vehicle used for setup are easily seen with the available road lighting. Manually adjusting shutter speed can also be useful for certain types of debugging (See Section 7.2, “Problem

2:EN Setup Software Found the Camera, But the Video Image is Too Dark or Just Black,” on page

47).

The following exposure times are supported

Camera Features

43

Page 42 Page 44
Image 43
Page 42 Page 44
Contents EN Camera Series Page EN Camera Series WarrantyDisclaimer CertificationsMailtrafficsales.americas@jai.com Trafficsales.emea@jai.com Table of Contents OP-IR OP-RED List of Figures Vii List of FiguresEN Camera Series Viii List of Figures List of Tables List of TablesEN Camera Series List of Tables Key Functions of the EN Camera IntroductionScope of this Manual Related DocumentsEN Camera Series Product Description Getting Started Network SettingsGetting Started Required EquipmentInstalling the Required Software Tutorial Start Up the EN Setup SoftwareTutorial Image CapturingCamera Properties Live Image Capturing/Focusing Live Image Capturing Measuring Box Position Quad Size Image Button Image Properties Light Sensor Connection EN Camera Series Image TransferADR Automatic Dynamic Range Control FTP Image TransferEN Camera Series Flash Nighttime Light Control Static IP Address Assignment EN Camera Series Time SynchronizationDhcp Client Debug Counters EN Camera Series MaintenanceFirmware Names and Descriptions Firmware Upgrade3 RS-232 PowerPC Debug Port EN Camera Series EN Camera Series Uploading Firmware Uploading the FirmwareTo Verify Version Numbers for all Firmware Updating the EN Application SoftwareUpdating the Camera’s H8 Firmware Updating the Fpga BitfileUpdating the Lib/Drv File Updating the OS ImageUploading Firmware 1 12-Pin Connector Connectors and CablesConnector Pin Configurations Connectors and Cables10/100 BaseT Ethernet Pinout Configuration EN Camera Series RS-232 Communication Cable Power Supplies and Power Cable SetupPower Supplies JAI Inc. Power CablesLens Mount Format Building Your Own Power CableAttaching the Power Cable to the Connector Attaching the Camera LensProgressive Scanning Camera FeaturesAsynchronous Reset Camera FeaturesTiming Chart 1 TSC-2030EN Timing Chart 2 TSC-1327EN Timing Chart 3 TSC-4032EN Camera ADR Control Related Registers EN Camera Series ADR Automatic Dynamic Range ControlElectronic Shutter EN Exposure Times Factory Default Settings of the ADR Shutter Min. and MaxGain Table BW EN Camera Video Amplifier Gain ControlGain Table Color EN Camera HDR Mode 4032EN Only Flash/Nighttime Light Control Ethernet External ControlColor Filter Array Color Version 1 RS-485TIF Format Image FormatsJpeg Format UDP Image Transfer on Setup ChannelTCP Message-Based Image Transfer on the Control Channel Image Buffering Factory Default Storage Setup of Image Buffering10 FTP EN Camera Series NTP Network Time Protocol FAQ and Troubleshooting Frequently Asked Questions and TroubleshootingFAQ and Troubleshooting Problem 12 IO Board Communication Error Problem 11 Light Sensor Connection is Not reliableProblem 16 Timestamp is Not Set to Current Local Time Problem 15 FlashErorr Appears in the Error RegisterInformation and Support Resources EN Camera Series Product Specifications Tables SpecificationsAppendix Processor Module Model TS-4032EN/TSC-4032EN Physical Dimensions TSC-4032EN Physical Dimensions TSC-2030EN/TSC-2076EN/TSC-1327ENSpectral Response B/W CCD TS-1327EN Spectral Response B/W CCDSpectral Response B/W Cmos TS-4032EN Spectral Response Color CCD TSC-1327EN IR Cut Filter Response for monochrome cameras Color filter spectrum response of TSC-1327EN Options Configurable Order Options for EN CamerasOP-IR OP-REDPage Europe, Middle East & Africa

TS(C)-1327EN, TS(C)-4032EN, TS(C)-2030EN, TS(C)-2076EN specifications

The JAI TS(C) series features a range of advanced cameras designed to meet the diverse needs of industrial imaging applications. Among the models in this series, the TS(C)-2076EN, TS(C)-2030EN, TS(C)-4032EN, and TS(C)-1327EN stand out for their innovative technologies and robust characteristics.

The TS(C)-2076EN is equipped with a 20 megapixel sensor that delivers high-resolution images with exceptional clarity. Utilized primarily in high-performance machines, its compact design ensures easy integration into existing systems. The camera offers a frame rate of up to 60 frames per second, making it suitable for high-speed applications. Furthermore, the TS(C)-2076EN features a global shutter, which eliminates motion blur, ensuring accurate image capture in dynamic environments.

Next in the lineup, the TS(C)-2030EN provides a balanced blend of speed and resolution with its 12 megapixel sensor, allowing for both detailed imaging and high frame rates of up to 120 fps. This model is particularly favored in applications such as 2D and 3D inspections, where quick analysis and precision are critical. The camera’s advanced image processing capabilities enhance performance, while its robust build ensures durability in various industrial settings.

The TS(C)-4032EN has been designed for applications requiring exceptional detail, leveraging a high-resolution 41 megapixel sensor. This model offers an impressive frame rate of 30 fps, making it ideal for capturing intricate details in static subjects. Its large sensor size and advanced optics increase light sensitivity, enabling it to perform well in low-light conditions. The camera also supports advanced connectivity options, facilitating seamless integration with various imaging systems.

Lastly, the TS(C)-1327EN focuses on high-speed imaging with a 3.2 megapixel sensor that can achieve frame rates of up to 300 fps. This camera is specifically engineered for fast-moving objects, making it suitable for applications in areas such as robotics and automation. Its compact design, along with superior synchronization features, make it an excellent choice for synchronized multi-camera setups.

Collectively, the JAI TS(C) series combines high image quality, rapid frame rates, and advanced imaging technologies to deliver versatile solutions for industrial applications. Each model is crafted with precision and built to endure, ensuring they remain reliable tools for meeting modern industrial imaging demands.
Top Page Image Contents