JAI TS(C)-4032EN, TS(C)-2076EN manual Disclaimer, Warranty, Certifications, EN Camera Series

Page 3

EN Camera Series

Disclaimer

Notice

The material contained in this manual consists of information that is proprietary to JAI Inc., and may only be used by the purchasers of the product. JAI Inc. makes no warranty for the use of its product and assumes no responsibility for any errors which may appear or for damages resulting from the use of the information contained herein. JAI Inc. reserves the right to make changes without notice.

Microsoft, Windows XP, Windows 2000, Windows 98, Windows NT, and Windows Explorer are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.

Warranty

For information about the warranty, please contact your factory representative.

Certifications

CE Compliance

The EN Camera series of cameras have been certified to conform to the requirements of Council Directive 89/336/EC for electromagnetic compatibility and to comply with the following European Standards:

Emissions:EN 55022A: 1998 + A1: 2000 + A2: 2003

Immunity:EN55024: 1998 + A1: 2001 + A2: 2003

All JAI Inc. products bearing the CE mark have been declared to be in conformance with the applicable EEC Council Directives. However, certain factory-installed options or customer-requested modifications may compromise electromagnetic compatibility and affect CE compliance. Please note that the use of interconnect cables that are not properly grounded and shielded may affect CE compliance.

Contact JAI Inc. Applications Engineering Department for further information regarding CE compliance.

FCC

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area may cause harmful interference, in which case the user will be required to correct the interference at his own expense.

Disclaimer

iii

Image 3
Contents EN Camera Series Page EN Camera Series WarrantyDisclaimer CertificationsMailtrafficsales.americas@jai.com Trafficsales.emea@jai.com Table of Contents OP-IR OP-RED List of Figures Vii List of FiguresEN Camera Series Viii List of Figures List of Tables List of TablesEN Camera Series List of Tables Key Functions of the EN Camera IntroductionScope of this Manual Related DocumentsEN Camera Series Product Description Getting Started Network SettingsGetting Started Required EquipmentInstalling the Required Software Tutorial Start Up the EN Setup SoftwareTutorial Image CapturingCamera Properties Live Image Capturing/Focusing Live Image Capturing Measuring Box Position Quad Size Image Button Image Properties Light Sensor Connection EN Camera Series Image TransferADR Automatic Dynamic Range Control FTP Image TransferEN Camera Series Flash Nighttime Light Control Static IP Address Assignment EN Camera Series Time SynchronizationDhcp Client Debug Counters EN Camera Series MaintenanceFirmware Names and Descriptions Firmware Upgrade3 RS-232 PowerPC Debug Port EN Camera Series EN Camera Series Uploading Firmware Uploading the FirmwareTo Verify Version Numbers for all Firmware Updating the EN Application SoftwareUpdating the Camera’s H8 Firmware Updating the Fpga BitfileUpdating the Lib/Drv File Updating the OS ImageUploading Firmware 1 12-Pin Connector Connectors and CablesConnector Pin Configurations Connectors and Cables10/100 BaseT Ethernet Pinout Configuration EN Camera Series RS-232 Communication Cable Power Supplies and Power Cable SetupPower Supplies JAI Inc. Power CablesLens Mount Format Building Your Own Power CableAttaching the Power Cable to the Connector Attaching the Camera LensProgressive Scanning Camera FeaturesAsynchronous Reset Camera FeaturesTiming Chart 1 TSC-2030EN Timing Chart 2 TSC-1327EN Timing Chart 3 TSC-4032EN Camera ADR Control Related Registers EN Camera Series ADR Automatic Dynamic Range ControlElectronic Shutter EN Exposure Times Factory Default Settings of the ADR Shutter Min. and MaxVideo Amplifier Gain Control Gain Table BW EN CameraGain Table Color EN Camera HDR Mode 4032EN Only Flash/Nighttime Light Control Ethernet External ControlColor Filter Array Color Version 1 RS-485TIF Format Image FormatsUDP Image Transfer on Setup Channel Jpeg FormatTCP Message-Based Image Transfer on the Control Channel Factory Default Storage Setup of Image Buffering Image Buffering10 FTP EN Camera Series NTP Network Time Protocol FAQ and Troubleshooting Frequently Asked Questions and TroubleshootingFAQ and Troubleshooting Problem 12 IO Board Communication Error Problem 11 Light Sensor Connection is Not reliableProblem 15 FlashErorr Appears in the Error Register Problem 16 Timestamp is Not Set to Current Local TimeInformation and Support Resources Specifications EN Camera Series Product Specifications TablesAppendix Processor Module Model TS-4032EN/TSC-4032EN Physical Dimensions TSC-4032EN Physical Dimensions TSC-2030EN/TSC-2076EN/TSC-1327ENSpectral Response B/W CCD TS-1327EN Spectral Response B/W CCDSpectral Response B/W Cmos TS-4032EN Spectral Response Color CCD TSC-1327EN IR Cut Filter Response for monochrome cameras Color filter spectrum response of TSC-1327EN Options Configurable Order Options for EN CamerasOP-IR OP-REDPage Europe, Middle East & Africa