JAI TM/TMC-4200CL JAI Power Cables, 12P-02S Interface Cable Pin# Lead Color Function

Page 36

Page 26

Installation

•The +12V lead is marked with a red stripe or white lettering; be sure not to reverse the leads.

•All connections must be properly insulated to prevent shorting.

5.2.4 (b) JAI Power Cables

When using JAI power cables such as the 12P-02S, please refer to the 12-pin connector pin-out diagram below. The cable pin-out diagram is shown in Figure 40 below. The color-coded leads use Gray for Ground and Yellow for +12V.

FIGURE 40. 12P-02S Interface Cable (optional)

+12 V

GND (Gray)

Male

Power (Yellow)

Video Out (Red Coax)

Analog Ch. A only

HD In (White Coax)

}

External sync input

VD In (Black Coax)

FIGURE 41. 12P-02S Interface Cable Pin Out

12P-02S Interface Cable

Pin#

Lead Color

Function

Pin#

Lead Color

Function

1

Gray

GND

7

Black coax

VD Input

2

Yellow

+12V DC

8

White coax shield

Strobe out

3

Red coax shield

GND (analog)

9

White coax

HD Input

4

Red coax

Video Out

10

Brown

RXD

5

Orange coax shield

GND (digital)

11

Blue

Reserved

6

Orange coax

VINIT IN

12

Black coax shield

TXD

Note: Make sure that the unused leads are not touching and that there is no possibility that exposed wires could cause the leads to short.

5.2.4 (c) Building Your Own Power Cable

Refer to the 12-pin connector pin-out in Figure 40 on page 26. Connect the Ground lead to pin #1, and the +12V DC lead to pin #2 of the 12-pin connector. Power must be DC-regulated, and of sufficient current to properly power the camera.

5.2.4 (d) Attaching the Power Cable to the Connector

The 12-pin connector is keyed and will only fit in one orientation. Follow these directions to properly attach the power cable to the camera connector:

1.Rotate the connector while applying slight pressure until the keyways line up.

2.Press the connector into place until firmly seated.

3.Plug the power cord into the 100V AC socket. This will power up the camera.

TM/TMC-4200CL Series Progressive Scan Cameras

Image 36

Contents TM/TMC-4200CL Series Progressive Scan Cameras Page Iii Notice CE ComplianceJAI PULNiX, Inc TM-4200CL Series Progressive Scan CameraPage Table of Contents Serial Communication Kit List of Figures List of FiguresList of Figures List of Tables List of TablesList of Tables Software Use and Installation Introduction Software InstallationDual-Tap TM-4200CL AccuPiXEL Series Camera-Control Software Setup installs Dual Tap AccuPIXel v Software Use and Installation Introduction Installing the Camera Link API DLL clserXXX.dllRunning Dual Tap AccuPiXEL Uninstalling the Software Screen grabber has an essential .dll fileSoftware Use and Installation Introduction TM/TMC-4200CL Camera TM/TMC-4200CL CameraGUI Features Graphical User InterfaceGraphical User Interface Using the CamLink Mode GigE ModeCheck Current Camera Setting Operating The Control SoftwareExposure Control Shutter SpeedScan Area Scan Area drop down box Graphical User Interface Gain Control Offset VoltageGain Ctrl Signals Video DepthImage Pre-Processing Graphical User Interface Trigger LUT Look-Up TablePositive or Negative LUT Selection Graphical User Interface Password Report SectionMain Menu Option Knee ControlEeprom Test PatternLoad SaveMain Menu Connectivity Main Menu AboutExit Hardware Introduction Product DescriptionTM/TMC-4200CL Series Progressive Scan Cameras Features Hardware IntroductionSystem Configuration WarrantyOutput Dual-Channel Auto Black Level Balancing and Gain BalancingInstallation Camera SetupGetting Started Connector Pin Configurations 2 a 12-Pin ConnectorPin Connector Pin DescriptionDigital I/O Connector Camera Link Connector Pin # DescriptionAnalog Output Connector Installation Camera Link Cable Power Supplies and Power Cable SetupPower Supplies JAI Power Cables Building Your Own Power CableAttaching the Power Cable to the Connector 12P-02S Interface Cable Pin# Lead Color FunctionInstallation Attaching the Analog Video Output Attaching the Camera LensFunctions and Operations Camera Rear PaneSensor Layer and Timing Digital Video OutputCamera Timing Chart Preset Scan Area Scan AreaFunctions and Operations Programmable Scan Area Full Scan Area 2x2 Binning BayerSub-sampling Digital Zoom X2 BinningSub-sampling Digital Zoom Functions and Operations Sub-sampling Digital Zoom Scan Area Start Points Preset Shutter Programmable Exposure-Continuous ModeAsynchronous No Shutter Mode Electronic Preset ShutterAsynchronous Programmable Exposure Mode External Trigger TimingPulse Width Control Mode Asynchronous Programmable External TriggerParticle Imaging Velocimetry Fixed Exposure Mode Pulse Width Control TriggerFunctions and Operations PWC PIV Mode Timing Scan Mode UnitFunctions and Operations Asynchronous Mode Chart Async no Shutter Async Preset and Prog. ShutterDynamic Range Control PIV Fixed ExpoProgrammable Look-Up Table LUT and Knee Control External Sync and Pixel Locking Serial Communication Kit Serial Communication KitSerial Communication Kit TM-4200CL Command List TM-4200CL Command ListScan Mode Lookup Table Channel BalanceVsub Dual Tap Digital Video Output Order Image Pre-processingMiscellaneous TM-4200CL Command Response Table Command Parameter End of Cmd DescriptionSerial Communication Kit Serial Communication Kit Problems and Solutions Problems and SolutionsSymptom No Video Symptom Dark VideoInformation and Support Resources Specifications TM-4200CL Camera Specifications TableAppendix AppendixAppendix 1 TM-4200CL Physical Dimensions Spectral ResponseAppendix W . j a i p u l n i x . c o m