EverFocus EZ610 manual Atw, Awb, Awc -Set, Manual, Burst, Color, Auto

Page 23

ATW

Auto Tracking White Balance: This mode can be used within the color

 

temperature range from 5,500°K to 6,000°K (eg, fluorescent light, outdoor,

 

sodium vapor lamp or inside tunnels).

AWB

Auto White Balance: This mode can be used within the color temperature range

 

from 2,500°K to 10,000°K. (default)

AWC ->SET

To find the optimal setting for the current luminance environment in this mode,

 

point the camera toward a sheet of white paper, and press “SET”. If the

 

environment changes, you will have to readjust it.

MANUAL

The manual adjustment mode enables a more precise adjustment. Please select

 

ATW or AWC first. Then change to manual adjustment mode and press the

 

SETUP button. Set the suitable color temperature, and increase or decrease the

 

red and blue color values at the same time while checking the color changes of

 

the objects in view.

 

Press “RET” to save all settings in this menu and return to the previous menu.

 

Press “END” to save all the menu settings and exit.

INDOOR

Select this option when the color temperature is 5,600°K.

OUTDOOR

Select this option when the color temperature is 3,300°K

Press “RET” to saves all settings in this menu and returns to the previous menu. Press “END” to save all the menu settings and exit.

3.3.5 DAY NIGHT

These settings control the operation of the camera when the illumination level changes. Choices are Color at all times; B/W at all times; or color when illumination is bright, switching to B/W in low light. EZ610 camera will have excellent IR sensitivity when displaying a low light B/W picture.

B/W

The picture is always displayed in B/W.

BURST

OFF/ON:

 

ON:

Retains the color burst information; minor color noise may appear

 

OFF:

when ambient illumination is low.

 

With color burst signal off, picture will be pure B/W.

 

Press “RET” to save all settings in the DAY/NIGHT menu and returns to the

 

previous menu.

 

Press “END” to save all the setting menus and exit.

COLOR

The picture is always displayed in color, even at low light levels.

 

NOTE: In “color” operation, there is an IR “cut” (blocking) filter between the

 

lens and the sensor; thus EZ610 camera has very little IR sensitivity when

 

the image is displayed in color. (default)

AUTO

The picture switches to color in a normal (bright) environment and switches

 

to B/W when the ambient illumination is low. The switching point is controlled

by the video signal level.

Note: AGC selection must be set as middle or high in order to employ the

23

Image 23
Contents EZ610 Operation Instruction Precautions WEE Federal Communication Commission Interference StatementTable of Contents OSD Menu Setting by Keyboard Lens Adjustment by Keyboard Product Overview FeaturesAccessory Parts List 3D-DNR SpecificationsFront view of EZ610 DimensionsCamera Body Related Products Camera Component DescriptionWiring and Mounting InstallationRS-485 cable 2nd axis Adjust Camera Position1st axis Sunshield 3rd axisSteps Control Key General Operation GuideBaud rate RS-485 ID RS485 ID & Baud Rate SettingReturn to Previous Close the Host Menu ScreenOSD Menu Tree OSD Menu SetupOff INT / LL English Exposure LensLEFT/RIGHT DefaultBLC GainOutdoor LevelOFF IndoorManual ATWAWB AWC -SET6 3DNR Disables 3DNR to keep the same amount of noiseEnables 3DNR to reduce the noise. default Level Noise reduction level from 0~100. default=30Special Pan MirrorFlip RotateMotion View Area SelectArea Display SensitivityINT AdjustReset OSD Menu Setting by Keyboard Remote control with EKB-500 keyboardRS 485 Wiring Camera Operation and Setup by DVR Remote Control with EverFocus DVRLens Adjustment by Keyboard 1 RS-485 WiringEverFocus Electronics Corp