Elinchrom BX 500RI, BX 250RI Features, Battery Installation, Hot-Shoe Connector with Screw-Lock

Page 18

English

EL-Skyport Transmitter SPEED //19350

Operating instructions :

2.4 GHz digital wireless Flash Trigger Transmitter

Features

EL-Skyport Transmitter Speed is designed with the latest 2.4 GHz Digital Wireless Technology.

• SLR Camera Sync speeds: SPEED mode up to

• Status LED for EL-Skyport mode and battery

1/250 s, STANDARD mode 1/160 - 1/200 s.

status.

• 5 selectable trigger modes, (4 Groups + All)

• Improved housing, battery drawer and

• 8 frequency channels.

switches.

• 40 Bit security encryption.

• New Hot-shoe with screw-lock.

• Up to 60 m range indoors for standard mode and

• New extra features; configure EL-Skyport with

up to 40 m in speed mode.

the new EL-Skyport PC / MAC software 3.0.

• Up to 120 m range outdoors for standard mode

 

and up to 60 m in speed mode.

You will appreciate the convenience of this

Battery life up to 6 Months - over 30’000 flashes. professional and powerful wireless device.

RX-feature buttons (Remote Control).

• Test trigger button and feature button.

Note: Shutter speed and distance range are influenced

• Integrated Hot-shoe (middle contact) improved.

by interference from other 2.4 GHz electronic equipment

SYNC-socket for direct connection improved.

and reflections of ceilings, walls, floors, furniture, metall,

• Two flash modes, standard and speed.

trees and humidiy in woods etc.

 

• The “Standard” mode is fully compatible with

For better performance the Transmitter and Receiver

previous EL-Skyport versions.

antenna should have direct sight, without any walls or

• The SPEED function is available for Ranger

objects in - between.

Quadra AS, BXRi 250 / 500 und D-Lite it and all

 

other units, when used with the Universal Speed.

 

Battery Installation

1.Pull the battery drawer out carefully.

2.Place the Lithium battery, see Fig. 1 for correct polarity.

3.Close the battery drawer.

!CAUTION:

Ensure correct polarity / minus pole on top.

Use only the Lithium Battery CR2430 3.0 V 19372.

Remove battery if the EL-Skyport Transmitter is not used for some time.

Never short-circuit battery poles.

Avoid direct sunlight or temperatures above 45°C. The battery may explode!

Hot-Shoe Connector with Screw-Lock

The new Hot-shoe connector with screw-lock and middle contact synchronisation is designed to fit digi- tal and analogue cameras with maximum sync output of 3 V (the middle contact is the positive pole).

Operating Instructions

Battery (19372)

 

Fig. 1

Minus pole on top

Flexible swivel

 

 

 

Antenna 360 ̊

Battery drawer

 

 

 

 

Hot-shoe with

 

 

screw lock and

 

 

SYNC socket

17

Image 18
Contents Page Table of contents EnglishEnglish CE marking Declaration of conformityDisposal and recycling CE Statements for EL-SkyportFlash tubes and modelling lamps Safety NotePower cable TransportIncluded basic features Operating instructions Switch and fuse Mains supplyBefore you start Mains fuseControl panel Overview of controls Setup Visual-Flash-Control VFC mode Programmable features ResetHow to „Reset the BX-Ri Modelling lamp modesOpen flash «test» Digital multi-displaySychronisation socket Eye-Cell advanced photocell sensorAutomatic Eye-Cell Pre-Flash Setup c.0 Eye-CELL SetupUsing the Standard Photocell Mode Intelligent Photocell-SensorManual Eye-Cell Pre-Flash Setup Setup Pre-Flash Timeframe only for advanced usersPre-Flash Timeframe Setting t.X Charge Ready Beep Features Frequency Channel Settings EL- Skyport Transceiver For Wireless Triggering SetupGroup Settings Power Steps Per PushFlashtube replacementEnglish Error ManagementBX 500Ri Contents Hot-Shoe Connector with Screw-Lock FeaturesBattery Installation Operating InstructionsEL-Skyport Sync Speed & Standard Mode Frequency ChannelEL-Skyport Transmitter Speed RX Features Integrated Hot-Shoe Sync 2.5 mm SocketTroubleshooting EL-Skyport ModulesCE Statements FCC Compliance and Advisory StatementDisposal and recycling