Sony SNP-3350 manual Preset Setup, Swing Setup

Page 32

Chapter 4. Using Web Viewer

■Preset Setup

To save a desired location for the Pan/Tilt or Zoom/Focus operation along with detailed camera settings for the location, configure the following options.

Category

Description

Number

Select a number to identify a preset. (Preset numbers 1 to 255 are available.)

Name

Name a preset.

Move

Moves to a selected preset when its number is selected.

Edit

Enables detailed camera settings to be configured for a preset.

 

Saves a preset; move to a desired location for the Pan/Tilt or Zoom/Focus operation,

Add

enter a preset number and name, and then press the Add button to save the location

 

as a preset.

Delete

Deletes an existing preset; select a preset number, and then press the Delete button.

Caution

New settings are saved only if you click the button on the right of the screen. To configure detailed camera settings for a preset, select a preset number, and then move the

camera to the preset before pressing the button.

■Sequence Setup

You can configure detailed sequence settings for each camera mode. Available camera modes are Swing, Group, Tour, Trace, and Auto Run, and they are described in the chart below.

Category

Description

Swing

Commands the camera to move between 2 selected presets, monitoring the

route.

 

Group

Recalls groups of multiple preset locations consecutively. A group can contain up

to 255 presets.

 

Tour

Recalls groups of presets consecutively in an orderly manner. Up to 6 groups can

be listed for this function.

 

 

Trace saves and reactivates patterns of custom camera movements. Up to 4

Trace & Auto Run

movement patterns can be memorized.

Auto Run commands the camera to automatically perform a preset sequence

 

 

action if no command has been entered via the controller for a while.

 

 

4.2.2.1. Swing

■Swing Setup

Category

Description

 

Mode

3 modes are available: Pan Swing, Tilt Swing, and P&T Swing.

Sequence

Pan Swing

Activates only the Pan operation for Swing monitoring.

Setup

Tilt Swing

Activates only the Tilt operation for Swing monitoring.

 

P&T Swing

Activates both the Pan and Tilt operations for Swing monitoring.

First Preset

 

Select the first preset for a route consisting of 2 presets.

Second Preset

Select the second preset for a route consisting of 2 presets.

Speed

 

Select the camera’s movement speed between the first and second presets.

 

(Levels 1 to 64 are available.)

 

 

DWT(Dwell Time)

Select the number of seconds to keep the PTZ camera on a preset location for

monitoring.

 

 

Caution

New settings are saved only if you click the button at the bottom of the screen.

The button operates the camera with the selected settings.

NETWORK PTZ CAMERA 62 User Guide

NETWORK PTZ CAMERA 63 User Guide

Image 32
Contents 37x/33x Network PTZ Camera SNP-3750/3350 User Guide Contents Product Warranty and Limited Liability PrefaceDo not handle the power plug with Wet handsProduct may become detached and fall It may cause electric shockDo not touch the camera lens Detailed Warnings and CautionsYou may severely damage the charge-coupled device CCD Product damage and/or fire may occurIntroduction FeaturesProduct Introduction Package Contents Part Names & FunctionsCamera Body Camera Wiring Interface Board Sold SeparatelyControl Signal Connection Baud Rate Settings Installing Camera & Network SetupProtocol Settings Communication Method Settings Communication Response SettingsTermination Settings Camera ID ChartNetwork PTZ Camera 20 User Guide 137 Resistance Ω/m SNP-3750/3350 Configuring Camera DIP Switches Connecting Camera Sa fety Cable and Attaching CameraXXX as the internal IP of your computer. XXX 0 ~ ① LAN / xDSL / Dhcp Setup Http//192.168.1.100Using Web Viewer ② Port SetupMonitoring Screen Compression Types Adjust the focus4CIF Stream Audio Check to use an audio input channel Video / AudioCategory Description Video Compression Streaming Continuous Jpeg Image TransmissionStreaming Engine Configure the RTP/RTSP streaming service Check to use RTSP/TCPCheck to use RTP/UDP Check to use RTP/MulticastMenu bar, select Media M, and then Open Network Stream N Address Streaming Engine Settings Settings levels are available, and 5 is the most sensitiveMotion Detection For RTSP/TCP and RTP/UDPPrivacy Category Description Enable Check to enable Video AnalyticsVideo Analytics White Balance  Mode Changes the current zoom power toCamera Are as belowHLC Activates the Highlight Compensation mode AGC Auto Gain Control Power On Resume Ssnr is disabled when the AGC mode is turned offOthers  Image HoldRecord Replay / Backup Swing Preset SetupSwing Setup Group Setup Tour SetupGroup TourPTZ Trace Setup Auto Run SetupTrace & Auto Run NetworkCheck to use the Ddns service Password Enter the password for the ID entered aboveLog in to the website, and then register your camera Pic 4-8. Product List IP Filtering You can allow or deny certain IPsCheck to apply the policy to the IP Filtering RulesAlarm Sensor Mail-FTP Alarm Recipient E-mail Alarm activates Address Smtp Server NameCategory Description Server Name Server Port Enter the port number of your FTP serverProduct Info Product InfoUser Time Time ServerCategory Description Video ControlUpgrade Log MessageTroubleshooting PC Requirements Category Minimun RequirementsModel Name SNP-335027.7 243.4 215.7 R75 Ø155 SpecificationsDimension GPL Software linux kernel, busybox, uboot GNU General Public LicenseAnnouncement No Warranty Signature Full Name PositionPlace Date 2009.11.01Network PTZ Camera 100 User Guide Network PTZ Camera 102 User Guide Sales Network