Samsung SDC-415 instruction manual Shutter condition and speed control, White Balance control

Page 13

Camera Operation

SHUTTER (condition and speed control)

Auto or manual control can be selected.

1.When the SETUP menu is on the screen, please position the arrow to point to 'SHUTTER' by using the DOWN button.

2.Please select the shutter mode by pressing the LEFT or RIGHT button.

FLK : Please select 'FLK' mode when flickering occurs on the screen, due to an imbalance between illumination and frequency.

NTSC Model:1/100, PAL MODEL: 1/120

ESC : Auto control of the shutter speed can be achieved. When ESC mode is on, the speed is controlled automatically according to the brightness of the screen.

MANUAL : The shutter speed can be controlled manually.

SETUP

LENSMANUAL

SHUTTER ESC

WHITE BAL. ATW

BACKLIGHT OFF

3.Please select 'MANUAL' mode if you wish to adjust the shutter manually.

You can select speed from ‘1/60’ to ‘1/120,000’sec (NTSC Models), ‘1/50’ to ‘1/120,000’sec (PAL Models).

4.Please press the SETUP button when all the settings are complete.

Note

When selecting DC/VIDEO lens, the shutter speed is fixed at 1/60.

While using the internal synchronous system, if the shutter setting is on

'ESC' and the camera is directly facing a bright fluorescent light, the image on the screen can be adversely affected. Therefore please choose the installation location with care.

When 'MANUAL' mode is on, the SENS UP function does not operate.

WHITE BALANCE control

The screen color can be adjusted by using the WHITE BALANCE function.

1.Please position the arrow to point to 'WHITE BAL' on the SETUP menu by using the UP and DOWN buttons.

2.Please select the mode you wish to operate by pressing the LEFT or RIGHT button.

SETUP

LENSMANUAL

SHUTTER ESC

WHITE BAL. ATW

BACKLIGHT OFF

Please select one of the 3 modes below.

ATW(Auto Tracking White Balance) : This mode can be used within the color temperature range 1,800°K ~ 10,500°K (eg, fluorescent light, outdoor, sodium vapor lamp or inside tunnels)

AWC(Auto White Balance Control) : Please press the SETUP button while the camera is directed at a piece of white paper to obtain the optimum state under current illumination. If the environment including the light source is changed, you have to adjust the white balance again.

MANUAL : The manual adjustment mode enables finer adjustment.

Please select ATW or AWC first. Please change to manual adjustment mode and press the SETUP button. Please set the appropriate color temperature, and then increase or decrease the red and blue color values while monitoring the color changes on the object.

Note

Under the following conditions the WHITE BALANCE function may not operate properly. In such cases, please select the AWC mode.

When the object’s surroundings have a very high color temperature (eg, a clear sky and sunset)

When the object’s surroundings are dark

If the camera directly faces a fluorescent light or is installed in a place where there are considerable changes in illumination, the WHITE BALANCE function may become unstable.

COLOR CCD CAMERA 24 User’s Manual

COLOR CCD CAMERA 25 User’s Manual

Image 13
Contents SDC-415 Series Signal System High Sensitivity Horizontal Resolution 530 TV LinesSsnr Samsung Super Noise Reduction Electronic IrisContents Them to physical shocks Strong light directly PrecautionsNames and Functions of Parts ComponentsFront Auto iris lens connection plug Mount adaptorSide Auto iris lens connectorMounting bracket screw hole When using an auto iris lens InstallationBack LensWhen using a CS-Mount lens When using a C-Mount lensConnecting to power Connecting to a monitorAC Power Type AC 24V, 500mA DC Power Type DC 12V, 500mA Camera Operation SettingsMenu DC/VIDEO Auto iris lens selection Lens selectionWhite Balance control Shutter condition and speed controlAGC Auto Gain Control BACKLIGHTBacklight CompensationSens UP Low illuminance Ssnr Samsung Super Noise reductionSpecial Color Exit Problems Troubleshooting TroubleshootingSDC-415NA SDC-415ND SDC-415PA SDC-415PD SpecificationsMemo