Planar 020-1229-00A user manual Regulatory Information

Page 98

Regulatory Information

Manufacturer's Name:

Planar Systems, Inc.

Manufacturer's Address:

1195 NW Compton Drive

Beaverton, OR 97006

Declares that the products Model Numbers: Planar UR8450-3D,UR8450-LX,UR8450-MX

Conforms with the provisions of:

Council Directive 2004/108/EC on Electromagnetic Compatibility;

EN55022:2010 Radiated and Conducted Emissions from IT Equipment

EN55024:2010 Immunity of IT Equipment

Including:

EN61000-4-2

Electrostatic Discharge

 

EN61000-4-3

Radiated Immunity

 

EN61000-4-4

Electrical Fast Transients

 

EN61000-4-5

Line Surge

 

EN61000-4-6

RF Conducted Susceptibility

 

EN61000-4-8

Magnetic Field Immunity

 

EN61000-4-11

Voltage Dips and Interrupts

And:

EN61000-3-2

Harmonic Current Emissions

 

EN61000-3-3

Voltage fluctuations and Flicker

Council Directive 2006/95/EC on Low Voltage Equipment Safety:

EN60950:2006+A11+A1+A12 Safety of IT Equipment

The Technical Construction File required by this Directive is maintained at the corporate headquarters of Planar Systems, Inc., 1195 NW Compton Drive, Beaverton, OR 97006.

Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Industry Canada (ICES-003): This Class A digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

Any changes or modifications to the display not expressly approved by Planar could void the user's authority to operate this equipment.

Other Certifications

CISPR 22

Planar UltraRes User Manual

91

Image 98
Contents Page Disclaimer Warranty and Service Plans RoHS Compliance StatementTrademark Credits ADA Compliance StatementTrademark Credits Table of Contents Connecting the Wired IR Module Downloading Additional Documentation and Firmware Table of Contents Introduction Important Safety Instructions Page European Union Disposal Information Burn-In Versus Temporary Image Retention What is Temporary Image Retention?Recommended Usage Normal Use Thermal Guidelines Cooling RequirementsBasic Concept of Planar UltraRes Display Using the Remote Control Supported Formats for Multiple Inputs Turning Power On/OffInput Setup Supported Formats for Single InputsInput Setup Before You Begin Installing a Planar UltraRes DisplayPlan Your Installation Tools/Equipment ListSupported Graphics Cards Recommended PCsPowering On/Off Planar UltraRes Displays Planar UltraRes in Standby Mode Powering On/Off Planar UltraRes Displays Powering On/Off Planar UltraRes Displays Unpacking and Checking Accessories LCD Module BoxKickstand Mounts to the display when Bracket Accessory Kit Following items are included in the accessory kitUnpacking and Checking Accessories LCD Installation Installing an UltraRes Display on a Wall Page Installing an UltraRes Display on a Wall Installing an UltraRes Display on a Wall Installing an UltraRes Display on a Wall Installing an UltraRes Display on a Wall Installing an UltraRes Display on a Wall Using the Kickstand Bracket Connections Connecting AC PowerConnecting the Wired IR Module Connecting Sources Setting Up UltraRes Using Multiple Inputs Using UltraRes Control SoftwareConnections Setting Up UltraRes Using Single Inputs Using the Remote Control Using the UltraRes Control Software Installing the UltraRes Control Software Page Page Installing USB Drivers Installing USB Drivers Using the UltraRes Control Software Model name Serial number Setting Up Sources Auto Power Off Timer Standby ModeTurning Local Dimming On or Off Changing Frame DelayChanging Backlight Intensity Upgrading Firmware Upgrading Firmware Upgrading Firmware Error Codes UltraRes Dimensions Display Dimensions Front and Side ViewsDisplay Dimensions Rear View Landscape Wall Mounts Front View Landscape Wall Mounts Sides Views Portrait Wall Mounts Front View Portrait Wall Mounts Sides Views Optional Pedestal Mount Front View Optional Pedestal Mount Top and Bottom Views Optional Pedestal Mount Single and Double Sided Optional Pedestal Mount Single and Double Sided Planar UltraRes Remote Monitoring Software Remote Monitoring HomeUnit Status Display ControlPower On/Off Source Setup Advanced Setup Admin Setup Network Setup Planar UltraRes Remote Monitoring Software Date and Time Use this page to change date and time information as neededAccess Control Software Setup Upgrading Network Firmware Reboot RS232 Communication Connecting the RS232 CableSetting Up Multiple Inputs Setting Up Single Inputs RS232 Commands Command FormatResponse Format Uwwwx=z CRCommand/Response Examples Supported UltraRes 4K Commands ERR TBDIF1 MI3 LCD Optical Specifications SpecificationsLCD Module Specifications Environmental Specifications Specification Maximum Minimum OptimalMultiple Input Compatibility Signal CompatibilityCompatible Video Sources Signal Compatibility Troubleshooting During Installation Error Codes in the UltraRes Control SoftwareError Code Meaning Solution Symptoms, Possible Causes and SolutionsSymptom Can’t Get PC to Output 4K @ 24/30Hz Possible CauseSymptoms, Possible Causes and Solutions Accessing Planar’s Technical Support Website Downloading Utility Software Regulatory Information Page Index Remote Monitoring, 67 normal use thermal guidelines Remote Monitoring, 71 sources via UltraRes Control Index