Vivotek IP7152, IP7151 manual Initial Access to the Network Camera, Check Network Settings

Page 10

Once installation is complete, the Administrator should proceed to the next section "Initial access to the Network Camera" for necessary checks and configurations.

Initial Access to the Network Camera

Check Network Settings

The Network Camera can be connected either before or immediately after software installation onto the Local Area Network. The Administrator should complete the network settings on the configuration page, including the correct subnet mask and IP address of gateway and DNS. Ask your network administrator or Internet service provider for the detail information. By default the Network Camera requires the Administrator to run installation every time it reboots. If the network settings are to remain unchanged, disable the Install option. Refer to “Network settings” on the System Configuration page for details. If any setting is entered incorrectly and cannot proceed to setting up the Network Camera, restore the factory settings following the steps in the “Troubleshooting” chapter of the Appendix.

Add Password to prevent Unauthorized Access

The default Administrator’s password is blank and the Network Camera initially will not ask for any password. The Administrator should immediately implement a new password as a matter of prudent security practice. Once the Administrator’s password is saved, the Network Camera will ask for the user’s name and password before each access. The Administrator can set up a maximum of twenty (20) user accounts. Each user can access the Network Camera except to perform system configuration. Some critical functions are exclusive for the Administrator, such as system configuration, user administration, and software upgrades. The user name for the Administrator is permanently assigned as “root”. Once the password is changed, the browser will display an authentication window to ask for the new password. Once the password is set, there is no provision to recover the Administrator’s password. The only option is to restore to the original factory default settings.

- 9 -

www.vivotek.com

T: 886-2-82455282

F: 886-2-82455532

Image 10
Contents Page Technical@vivotek.com Before You Use This Product Table of Contents Ddns Rtsp SDP Package Contents Installation Hardware installationSoftware installation 6 5 4 3 2Check Network Settings Initial Access to the Network CameraAdd Password to prevent Unauthorized Access Installing plug-in How to UseAuthentication 886-2-82455282 886-2-82455532 Primary user’s capability Main Screen with Camera View886-2-82455282 886-2-82455532 886-2-82455282 886-2-82455532 Here is the layout in Firefox when it is Jpeg streaming Digital Zoom MP4 RecordingSnapshot LanguageClient settings 886-2-82455282 886-2-82455532 Fine-tuning for Best Performance Administrator’s capabilityDigital output For Viewing by Mobile Phone For Best Real-time Video Images Protect Network Camera by passwords Opening accounts for new usersBuild a security application Software revision upgrade Definitions in Configuration System parameters Security settings 886-2-82455282 886-2-82455532 Network settings Network typeHttp Rtsp Streaming886-2-82455282 886-2-82455532 Url http//Network Camera/setup/network.html Wlan Settings IP7152 only Tkip AES Ddns Access List Audio and Video Video SettingsVideo orientation Audio settings Url http//Network Camera/setup/audiovideo.htm Image Settings Privacy Mask 886-2-82455282 886-2-82455532 CCD Settings Motion detection Url http//Network Camera/setup/motion.htm Camera control 886-2-82455282 886-2-82455532 Camera control panel doesn’t show up in `Fixed Camera’ mode Preset position Custom command Application Event Server 886-2-82455282 886-2-82455532 Media Recording Url http//Network Camera/setup/recording.htm System log Viewing system parameters Url http//Network Camera/setup/parafile.htm Maintenance Url http//Network Camera/setup/maintain.htm Troubleshooting Status LEDOverview URL commands of the Network CameraStyle convention General CGI URL syntax and parameters Security levelGet server parameter values Method GET/POSTSet server parameter values Parameter pairUpdate Available parameters on the server Valid Values DescriptionNTP server 886-2-82455282 886-2-82455532 886-2-82455282 886-2-82455532 GMT Integer Inactive status Group security Name Value Multicast video port Build-in Set bit rate in bps when choose Cmos Window Wini0~2height Height Motion Providerhos Logemerg Name Value Security Description 886-2-82455282 886-2-82455532 Videoincodec Audiooutcodec Detection Parameter Value Security Description Port to connect the server Video clip in seconds Drive the digital output Query status of the digital input Query status of the digital output Capture single snapshot QualityAccount management System logs Upgrade firmware IP filteringRtsp SDP 101 Technical specifications System and HardwareImage settings Technology License Notice MPEG-4 AAC Technology MPEG-4 Visual TechnologyElectromagnetic Compatibility EMC Liability