Vivotek IP7151, IP7152 manual Troubleshooting, Status LED

Page 65

Reset and restore

There is a button in the back of the Network Camera. It is used to reset the system or restore the factory default settings. Sometimes resetting the system sets the system back to normal state. If the system problems remain after reset, restore the factory settings and install again.

Restoring the factory

defaults will erase any previous settings. Reset or restore the system after power on.

Appendix

A. Troubleshooting

Status LED

The following table lists the LED patterns in general.

Condition	LED color
Loading system after power on	Steady green and blink red (once)

During booting procedure	Blinking red

Detecting and setting network	Steady green till IP address is confirmed

After network is setup (system up)	Blinking green every other second and
	steady red

During the upgrade firmware process	Blink green / orange every second and fast
	blink red

RESET: Click on the button.

RESTORE:

1. Press on the button continuously.

2. Wait for self-diagnostic to run twice.

3. Free the button as soon as the second self-diagnostic starts.

- 64 -

www.vivotek.com

T: 886-2-82455282

F: 886-2-82455532

Image 65

Contents Page Technical@vivotek.com Before You Use This Product Table of Contents Ddns Rtsp SDP Package Contents Hardware installation Installation6 5 4 3 2 Software installationAdd Password to prevent Unauthorized Access Initial Access to the Network CameraCheck Network Settings Authentication How to UseInstalling plug-in 886-2-82455282 886-2-82455532 Main Screen with Camera View Primary user’s capability886-2-82455282 886-2-82455532 886-2-82455282 886-2-82455532 Here is the layout in Firefox when it is Jpeg streaming MP4 Recording Digital ZoomLanguage SnapshotClient settings 886-2-82455282 886-2-82455532 Digital output Administrator’s capabilityFine-tuning for Best Performance For Viewing by Mobile Phone For Best Real-time Video Images Opening accounts for new users Protect Network Camera by passwordsBuild a security application Software revision upgrade Definitions in Configuration System parameters Security settings 886-2-82455282 886-2-82455532 Network type Network settingsRtsp Streaming Http886-2-82455282 886-2-82455532 Url http//Network Camera/setup/network.html Wlan Settings IP7152 only Tkip AES Ddns Access List Video orientation Video SettingsAudio and Video Audio settings Url http//Network Camera/setup/audiovideo.htm Image Settings Privacy Mask 886-2-82455282 886-2-82455532 CCD Settings Motion detection Url http//Network Camera/setup/motion.htm Camera control 886-2-82455282 886-2-82455532 Camera control panel doesn’t show up in `Fixed Camera’ mode Preset position Custom command Application Event Server 886-2-82455282 886-2-82455532 Media Recording Url http//Network Camera/setup/recording.htm System log Viewing system parameters Url http//Network Camera/setup/parafile.htm Maintenance Url http//Network Camera/setup/maintain.htm Status LED TroubleshootingStyle convention URL commands of the Network CameraOverview Security level General CGI URL syntax and parametersMethod GET/POST Get server parameter valuesParameter pair Set server parameter valuesUpdate Valid Values Description Available parameters on the serverNTP server 886-2-82455282 886-2-82455532 886-2-82455282 886-2-82455532 GMT Integer Inactive status Group security Name Value Multicast video port Build-in Set bit rate in bps when choose Cmos Window Wini0~2height Height Motion Providerhos Logemerg Name Value Security Description 886-2-82455282 886-2-82455532 Videoincodec Audiooutcodec Detection Parameter Value Security Description Port to connect the server Video clip in seconds Drive the digital output Query status of the digital input Query status of the digital output Quality Capture single snapshotAccount management System logs IP filtering Upgrade firmwareRtsp SDP 101 System and Hardware Technical specificationsImage settings MPEG-4 AAC Technology MPEG-4 Visual Technology Technology License NoticeLiability Electromagnetic Compatibility EMC