Adcom GTP-760 owner manual Programming Your Own Commands

Page 27

For tuner functions (changing stations, etc.):

1.Press the tuner source selector button. It will flash red.

2.Press the tuning up (or tuning down) function button to change stations. The tuner source selector will flash red to confirm that the function button you’ve selected actually triggers a command. (Again, use the table to see which buttons are preprogrammed.)

Press the CD source selector first to access preprogrammed commands for ADCOM CD players.

NOTE: You can program new commands over the preprogrammed commands in tuner and CD if you wish. However, you cannot program any buttons, even those unprogrammed with GTP-760 command codes, while you’re in main mode. This safety feature assures you that you will always be able to fully enjoy the GTP-760’s capabilities.

Programming Your Own Commands

You can supplement preprogrammed commands with commands to operate other components. Before you begin to follow these steps, note the status LED located at the top left corner just above the remote’s button panel: It will flash red, orange, or green to signal particular functions as you enter new commands into your ADCOM remote.

Begin by deciding which source component’s commands you will be transferring to the ADCOM remote. Then press the appropriate source selector button. For example, if you’re teaching your ADCOM remote commands for your DVD player, press the DVD source selector first. You can “teach” your remote new commands for any function button (except backlight) after you’ve selected DVD, VCR, TUNER, V.AUX, CD, Dig.1 or Dig.2.

1.Place the source component’s remote “head to head” with the ADCOM remote. They should be in line with each other about 2 to 3 inches apart.

2.Press the ADCOM remote’s appropriate source selector and select/play buttons simultaneously. Hold both buttons until the status LED turns orange and the source selector button glows red. Both indica tors should remain lit.

3.Decide which function button on the ADCOM remote you want to learn a new command. Press it. The orange status LED will begin to flash and the source selector LED will go out.

4.Find the corresponding button on the source component’s remote. Press and hold it until the status LED on the ADCOM remote flashes green once and remains green until the button on the source remote is released. Once the button on the source remote is released, the status LED will start flashing orange again.

5.Verify that the ADCOM remote has learned the new command by pressing and holding the same button on the source remote. The ADCOM remote’s status LED should flash green twice and then go back to steady orange. This indicates successful programming. Release the button on the source remote.

Repeat Steps 3 through 5 for any other commands you want to teach your ADCOM remote for that source component.

Save the commands you’ve just programmed into the ADCOM remote by pressing and holding the appropriate source selector and select/play buttons simultaneously. Hold until the status LED and source selector LED flash twice and then go out. Repeat these steps for any other source commands you wish to program.

26

Page 26 Page 28
Image 27
Page 26 Page 28
Contents GTP-760 Page Explanation of Graphic Symbols Safety NotificationConcealed Shipping Damage Adcom Protection Plan USA onlyTable of Contents Initial Setup On Screen DisplaySurround Modes Tuner Room Front Panel Controls Product FeaturesPage Center Channel and Subwoofer Rear Panel Inputs & Outputs System ConnectionsYellow centers Digital Audio inputsComposite or S-Video? DVD Digital Audio/Standard Composite Video Inputs I g g e r o u t VCR Inputs and Outputs 21 12 Volt Trigger OutputVideo Aux Input Room 2 OutputsVideo Processor Inputs and Outputs Tape Inputs and Outputs Standard Composite Video Monitor OutputsCD Inputs Video Inputs and Outputs Video Processor On/Off Switch Remote Control ConnectionsPreamplifier Outputs 27 5.1 Channel Inputs AC Power Cord Receptacle export modelsAC Convenience Outlets 115VAC models Remote Control54 55 Input Selectors tape, LD PowerVolume Up/Down Tuning Up/Down44 FM/AM Down arrow/StopSelect/Play ShiftCenter Down Rear UpRear Down Center UpMain Tuner All Others Dig.1Dig.2 Programming Your Adcom GTP-760 Remote Controller Using Preprogrammed CommandsIntroduction Programming Your Own Commands Macro Commands Deleting clearing Individual Programmed CommandsINSTALLING/CONNECTING the GTP-760 PlacementConnections What this section is all about Channel DelaysDIM L DIM C DIM R DIM LS DIM RS Preset 1 Main Small, Center On, Rears On, Subwoofer On Preset 2 Main Large, Center On, Rears On, Subwoofer OffPreset 3 Main Large, Center On, Rears On, Subwoofer On Sound Meter By EarInput Settings Basic Operation Operating Mode SelectionPage Tuner Selecting stations Programming Preset StationsOperating Room 2 From the Front Panel Listening to Preset StationsSetting Room 2 Playback Volume Room 2 Operation IntroductionOperating Room 2 From Room Trouble ShootingPage CARE, MAINTENANCE, and Service Specifications GTP-760 This page has been interntionally left blank Timber Lane Marlboro, NJ Tel 732 Fax 732

GTP-760 specifications

The Adcom GTP-760 is a high-performance audio/video surround processor that combines advanced technology with ease of use, delivering an exceptional home theater experience. At the heart of the GTP-760 is its extensive support for various audio formats, including Dolby Digital, DTS, and MPEG. This enables the processor to provide an immersive audio experience, allowing users to enjoy their favorite movies, music, and games with remarkable clarity.

One of the standout features of the GTP-760 is its multiple input options. It comes equipped with a range of analog and digital inputs, including HDMI, allowing for seamless integration with a variety of audio and video sources. The HDMI inputs support 4K video pass-through and scaling, making the GTP-760 a future-proof option for home theater setups. Additionally, the inclusion of S-Video, composite, and component video connections ensures compatibility with older devices.

The GTP-760 also offers a comprehensive equalization system, allowing users to tailor their audio output to suit their room’s acoustics and personal preferences. The built-in audio DSP (Digital Signal Processor) delivers advanced sound processing capabilities, enhancing the overall listening experience. With customizable sound modes, users can select settings optimized for music, movies, or gaming, ensuring versatility for different content types.

User friendliness is a focal point of the GTP-760 design. The intuitive front panel controls and the ergonomic remote make navigation a breeze, while the backlit display provides clear visibility, even in low light environments. Additionally, the processor features programmable memory settings, allowing users to save different configurations for quick access.

Beyond audio performance, the GTP-760 offers robust video processing capabilities. It supports various video formats, ensuring high-quality picture output regardless of the source. The unit’s solid build quality and premium components contribute to its reliability and longevity.

In conclusion, the Adcom GTP-760 is a well-rounded surround processor that delivers outstanding sound quality and video processing capabilities. Its variety of input options, advanced audio technologies, and user-friendly design make it an excellent choice for both amateur and avid home theater enthusiasts. With its ability to enhance audio-visual experiences, the GTP-760 stands out as a remarkable addition to any entertainment system.
Top Page Image Contents