Adcom GTP-760 owner manual Listening to Preset Stations, Room 2 Operation Introduction

Page 38

Listening to “Preset” Stations

1)Select tuner and either FM or AM.

2)Press the appropriate preset button (or shift + the preset button for choices higher than “preset 7”).

4.3Room 2 Operation

Introduction

The GTP-760’s “Room 2” circuitry gives you the ability to simultaneously enjoy two different audio/video sources in two different areas of your home. For instance, you can watch a DVD movie in the main family room while someone else enjoys a satellite broadcast or CD in the bedroom.

Operating “Room 2” From the Front Panel

The room 2 button on the front panel of the GTP-760 performs three separate functions: Room 2 power ON; Room 2 status; and Room 2 power OFF.

1)To turn Room 2 power ON, press the room 2 button once. The LED in the center of the room 2 button will light to tell you that “room 2” capability is on.

2)Once Room 2 is active, press the room 2 button again to display Room 2 status. The LED’s in the center of the six front panel analog source selectors will light to show you that you can route any of those sources to the GTP-760’s “Room 2” outputs. If one of the six source LED’s blinks, that source is already selected for room 2 distribution. (Note: You cannot direct a digital source — DVD, digital 1, or digital 2 — to the Room 2 outputs.)

Choose the source you wish to direct to the room 2 outputs by pushing one of the lighted source selectors. The LED’s in the other source selectors will go out and the name of the source you’ve just chosen for room 2 distribution will briefly appear in the information display window. After five (5) seconds, the display will change to show the room 1 (main) source but the room 2 LED will still glow, indicating that a room 2 source is now active.

You can verify the room 2 source selection any time “room 2” capability is active (i.e., any time the room 2 LED is illuminated) by simply pressing the room 2 button again. You’ll see all six analog source selector LED’s light. The active room 2 source LED will blink and the name of that source will show in the information display. You’ll have ten (10) seconds to change the room 2 source by simply pressing any other illuminated source selector.

3)To power Room 2 OFF, press and hold the room 2 button until the red LED at the center of the button goes out (about 5 seconds time).

Setting “Room 2” Playback Volume

You can change “room 2” volume only by using the remote control. There is no way to adjust “room 2” playback level from the GTP-760’s front panel alone.

1)Press the remote control’s main source selector once. This makes sure the remote is ready to generate GTP-760 command codes.

2)Press the room 2 button twice to access the room 2 status mode.

3)Use the remote control’s volume up/down buttons within ten (10) seconds of pressing room 2. The front panel display will show room 2 level changes as you make them and will then revert to normal display mode ten (10) seconds after the GTP-760 receives the last volume adjust command.

37

Page 37 Page 39
Image 38
Page 37 Page 39
Contents GTP-760 Page Safety Notification Explanation of Graphic SymbolsAdcom Protection Plan USA only Concealed Shipping DamageTable of Contents Surround Modes Tuner Room Initial SetupOn Screen Display Product Features Front Panel ControlsPage Digital Audio inputs Rear Panel Inputs & Outputs System ConnectionsYellow centers Center Channel and SubwooferComposite or S-Video? DVD Digital Audio/Standard Composite Video Inputs I g g e r o u t 21 12 Volt Trigger Output VCR Inputs and OutputsVideo Processor Inputs and Outputs Video Aux InputRoom 2 Outputs CD Inputs Tape Inputs and OutputsStandard Composite Video Monitor Outputs Video Inputs and Outputs Preamplifier Outputs Video Processor On/Off SwitchRemote Control Connections AC Power Cord Receptacle export models 27 5.1 Channel InputsRemote Control AC Convenience Outlets 115VAC models54 55 Tuning Up/Down PowerVolume Up/Down Input Selectors tape, LDShift Down arrow/StopSelect/Play 44 FM/AMCenter Up Rear UpRear Down Center DownDig.2 Main Tuner All OthersDig.1 Introduction Programming Your Adcom GTP-760 Remote ControllerUsing Preprogrammed Commands Programming Your Own Commands Deleting clearing Individual Programmed Commands Macro CommandsConnections INSTALLING/CONNECTING the GTP-760Placement Channel Delays What this section is all aboutDIM L DIM C DIM R DIM LS DIM RS Preset 3 Main Large, Center On, Rears On, Subwoofer On Preset 1 Main Small, Center On, Rears On, Subwoofer OnPreset 2 Main Large, Center On, Rears On, Subwoofer Off By Ear Sound MeterInput Settings Operating Mode Selection Basic OperationPage Programming Preset Stations Tuner Selecting stationsRoom 2 Operation Introduction Listening to Preset StationsSetting Room 2 Playback Volume Operating Room 2 From the Front PanelTrouble Shooting Operating Room 2 From RoomPage CARE, MAINTENANCE, and Service Specifications GTP-760 This page has been interntionally left blank Timber Lane Marlboro, NJ Tel 732 Fax 732

GTP-760 specifications

The Adcom GTP-760 is a high-performance audio/video surround processor that combines advanced technology with ease of use, delivering an exceptional home theater experience. At the heart of the GTP-760 is its extensive support for various audio formats, including Dolby Digital, DTS, and MPEG. This enables the processor to provide an immersive audio experience, allowing users to enjoy their favorite movies, music, and games with remarkable clarity.

One of the standout features of the GTP-760 is its multiple input options. It comes equipped with a range of analog and digital inputs, including HDMI, allowing for seamless integration with a variety of audio and video sources. The HDMI inputs support 4K video pass-through and scaling, making the GTP-760 a future-proof option for home theater setups. Additionally, the inclusion of S-Video, composite, and component video connections ensures compatibility with older devices.

The GTP-760 also offers a comprehensive equalization system, allowing users to tailor their audio output to suit their room’s acoustics and personal preferences. The built-in audio DSP (Digital Signal Processor) delivers advanced sound processing capabilities, enhancing the overall listening experience. With customizable sound modes, users can select settings optimized for music, movies, or gaming, ensuring versatility for different content types.

User friendliness is a focal point of the GTP-760 design. The intuitive front panel controls and the ergonomic remote make navigation a breeze, while the backlit display provides clear visibility, even in low light environments. Additionally, the processor features programmable memory settings, allowing users to save different configurations for quick access.

Beyond audio performance, the GTP-760 offers robust video processing capabilities. It supports various video formats, ensuring high-quality picture output regardless of the source. The unit’s solid build quality and premium components contribute to its reliability and longevity.

In conclusion, the Adcom GTP-760 is a well-rounded surround processor that delivers outstanding sound quality and video processing capabilities. Its variety of input options, advanced audio technologies, and user-friendly design make it an excellent choice for both amateur and avid home theater enthusiasts. With its ability to enhance audio-visual experiences, the GTP-760 stands out as a remarkable addition to any entertainment system.
Top Page Image Contents