Adcom GTP-760 owner manual Tuner Selecting stations, Programming Preset Stations

Page 37

4.2 The Tuner

Selecting stations

1)Select the tuner input via the front panel or remote control button. The information display will show the most recently received broadcast frequency.

2)If the band you want (AM or FM) is already displayed, proceed to step 3) below. If not, push the FM/AM selector to change to the appropriate band.

3)Choose your preferred tuning method (seek or manual) by pressing the front panel seek/manual button.

While in “seek” mode, the tuning buttons will take you to the next active frequency. In “manual” mode, the tuning buttons will step to the next available frequency even if it is unused.

4)Use the tuning buttons to select the station you wish to listen to.

Programming “Preset” Stations.

The GTP-760 can memorize up to 14 AM and 14 FM signals for instant recall. Place your favorite stations in memory by:

1)Select either FM or AM as described above. Note the stations you want to preset. Starting at the lowest end of the frequency range (88.1 for FM, 520 for AM), tune to the first station you want to program into memory.

2)Press the preset 1 button and hold it for approximately three (3) seconds. (Remember to push

the remote’s tuner source selector before using the keypad.) When you see “Preset 1” appear in the information display and the LED in the preset 1 button light, that frequency has been placed in the preset memory.

3)Tune to the next desired frequency and follow the same instructions but use “Preset 2” to commit this new broadcast frequency to memory.

4)Continue for all presets up to and including the seventh.

5)Setting presets 8 through 14 require the use of the shift button.

•Select the desired frequency for preset # 8. Press shift and then hold preset button 1 for three seconds. When you see “Preset 8” appear in the information display and the LED’s in the front panel preset 1 and shift buttons light, that frequency is memorized.

•Select the frequency for preset # 9. Follow the instructions above but substitute preset button2 in place of preset button 1. (Remember that the shift button adds a “7” to the nominal preset button value. Thus, shift + 2 actually means “Preset 9” and so on.)

•Continue as above until all 14 presets are used or until you run out of “favorite” stations, whichever comes first.

6)Select the other broadcast band (AM or FM) and begin programming again. Follow the instructions above. When you’re finished, you’ll be able to listen to any of these favorite frequencies by pushing just one or two buttons.

36

Page 36 Page 38
Image 37
Page 36 Page 38
Contents GTP-760 Page Explanation of Graphic Symbols Safety NotificationConcealed Shipping Damage Adcom Protection Plan USA onlyTable of Contents On Screen Display Initial SetupSurround Modes Tuner Room Front Panel Controls Product FeaturesPage Yellow centers Rear Panel Inputs & Outputs System ConnectionsDigital Audio inputs Center Channel and SubwooferComposite or S-Video? DVD Digital Audio/Standard Composite Video Inputs I g g e r o u t VCR Inputs and Outputs 21 12 Volt Trigger OutputRoom 2 Outputs Video Aux InputVideo Processor Inputs and Outputs Standard Composite Video Monitor Outputs Tape Inputs and OutputsCD Inputs Video Inputs and Outputs Remote Control Connections Video Processor On/Off SwitchPreamplifier Outputs 27 5.1 Channel Inputs AC Power Cord Receptacle export modelsAC Convenience Outlets 115VAC models Remote Control54 55 Volume Up/Down PowerTuning Up/Down Input Selectors tape, LDSelect/Play Down arrow/StopShift 44 FM/AMRear Down Rear UpCenter Up Center DownDig.1 Main Tuner All OthersDig.2 Using Preprogrammed Commands Programming Your Adcom GTP-760 Remote ControllerIntroduction Programming Your Own Commands Macro Commands Deleting clearing Individual Programmed CommandsPlacement INSTALLING/CONNECTING the GTP-760Connections What this section is all about Channel DelaysDIM L DIM C DIM R DIM LS DIM RS Preset 2 Main Large, Center On, Rears On, Subwoofer Off Preset 1 Main Small, Center On, Rears On, Subwoofer OnPreset 3 Main Large, Center On, Rears On, Subwoofer On Sound Meter By EarInput Settings Basic Operation Operating Mode SelectionPage Tuner Selecting stations Programming Preset StationsSetting Room 2 Playback Volume Listening to Preset StationsRoom 2 Operation Introduction Operating Room 2 From the Front PanelOperating Room 2 From Room Trouble ShootingPage CARE, MAINTENANCE, and Service Specifications GTP-760 This page has been interntionally left blank Timber Lane Marlboro, NJ Tel 732 Fax 732

GTP-760 specifications

The Adcom GTP-760 is a high-performance audio/video surround processor that combines advanced technology with ease of use, delivering an exceptional home theater experience. At the heart of the GTP-760 is its extensive support for various audio formats, including Dolby Digital, DTS, and MPEG. This enables the processor to provide an immersive audio experience, allowing users to enjoy their favorite movies, music, and games with remarkable clarity.

One of the standout features of the GTP-760 is its multiple input options. It comes equipped with a range of analog and digital inputs, including HDMI, allowing for seamless integration with a variety of audio and video sources. The HDMI inputs support 4K video pass-through and scaling, making the GTP-760 a future-proof option for home theater setups. Additionally, the inclusion of S-Video, composite, and component video connections ensures compatibility with older devices.

The GTP-760 also offers a comprehensive equalization system, allowing users to tailor their audio output to suit their room’s acoustics and personal preferences. The built-in audio DSP (Digital Signal Processor) delivers advanced sound processing capabilities, enhancing the overall listening experience. With customizable sound modes, users can select settings optimized for music, movies, or gaming, ensuring versatility for different content types.

User friendliness is a focal point of the GTP-760 design. The intuitive front panel controls and the ergonomic remote make navigation a breeze, while the backlit display provides clear visibility, even in low light environments. Additionally, the processor features programmable memory settings, allowing users to save different configurations for quick access.

Beyond audio performance, the GTP-760 offers robust video processing capabilities. It supports various video formats, ensuring high-quality picture output regardless of the source. The unit’s solid build quality and premium components contribute to its reliability and longevity.

In conclusion, the Adcom GTP-760 is a well-rounded surround processor that delivers outstanding sound quality and video processing capabilities. Its variety of input options, advanced audio technologies, and user-friendly design make it an excellent choice for both amateur and avid home theater enthusiasts. With its ability to enhance audio-visual experiences, the GTP-760 stands out as a remarkable addition to any entertainment system.
Top Page Image Contents