MRV Communications EM316EDFA-LPR, EM316EDFA-BR manual Front Panel, LEDs, DIP Switches

Page 13
3.2 Front Panel

Fiber Driver® EM316EDFA User Guide

3.2 Front Panel

Figure 3 -- EM316EM316EDFA-BR / EM316EDFA-LPR Front Panel

3.3 LEDs

PWR/NMS Power

On – DC +5V power is applied to the card

SD Input Optical Power

On – Input signal greater than the input threshold

 

setting

OPTICAL OUTPUT OK

On – Output power is greater than -2 dBm, for apc

Output Optical Power

mode or -10 dBm for agc mode

3.4 DIP Switches

The EM316EDFA-BR is pre-configured in booster mode. There are no user-selectable switches.

The EM316EDFA-LPR is pre-configured in inline pre-amplifier mode. There are no user-selectable switches to operate either inline or as a pre-amplifier.

The DIP switch block at the underside of the module has six switches. Only switch 6 affects operation of the amplifier module. Use switch 6 to enable or disable network management.

Switch #

Function

Setting

1-5

N/A

Reserved

6

Management Enable

Default: ON = enable management

P/N 1294008-001 Rev D2

4

Image 13
Contents EM316EDFA-LPR EM316EDFA-BRErbium Doped Fiber Amplifier Booster Erbium Doped Fiber Inline Pre-AmplifierTable of Contents 3 Preparation and Installation2 Introduction to EM316EDFA Optical Amplifiers 5 Module ManagementTable of Figures 6 Appendix1.1 Trademarks 1 Preliminary Considerations1.2 Copyright 1.3 Customer SupportFiber Driver EM316EDFA User Guide 1.4 ComplianceFiber Driver Chassis Fiber Driver Modules1.5.2 Laser Safety 1.5General Safety1.5.1Cautions and Warnings Fiber Driver EM316EDFA User Guide 1.5.3 Laser Device Classifications1.5.5 Workplace Preparation 1.5.4 Static Electricity1.7 Latest Revision and Related Documents 1.6 About This ManualFiber Driver EM316EDFA User Guide Document NumberFiber Driver EM316EDFA User Guide 2 Introduction to EM316EDFA Optical AmplifiersC-band pre-amplifier 2.1.3EDFA Alarm Outputs 2.1 Features2.1.2EDFA Control Inputs 3.1 Unpacking the Fiber Driver Module 3 Preparation and Installation3.2 Front Panel 3.4 DIP Switches3.3 LEDs 3.5.1.1.2Procedure 3.5 Module InstallationFiber Driver EM316EDFA User Guide 3.5.1.1.1ToolsP/N 1294008-001Rev D2 4.1 Network Management Control and Monitoring 4 EDFA Features4.1.1 Management Control from the Network 4.1.2 EM316EDFA Alarm Output Pins4.1.3 Operating Parameters 5 Module Management Fiber Driver EM316EDFA User Guide 5.1 Serial Console InterfaceRS-232 Serial Port5.2 EM316LNXNM-OTCommand Line Interface CLI P/N 1294008-001Rev D2 5.2.1 EM316LNXNM-OTBoot and CLI Login5.2.2 CLI Navigation 5.2.3.1“show version” 5.2.3 Login Context Commands and Examples5.2.3.2“show log” fiberdriver# show running-config 5.2.3.3“show running-config”P/N 1294008-001Rev D2 fiberdriver# show startup-config 5.2.3.4“show startup-config”P/N 1294008-001Rev D2 Fiber Driver EM316EDFA User Guide 5.2.3.5 Configuring System Parameters5.2.4.1“show” 5.2.4 Chassis ContextFiber Driver EM316EDFA User Guide 5.2.4.2 Other CommandsP/N 1294008-001Rev D2 Command 5.2.5 Slot Context Commands and ExamplesFiber Driver EM316EDFA User Guide DescriptionFiber Driver EM316EDFA User Guide 5.2.5.1 “?” 5.2.5.2“list” Fiber Driver EM316EDFA User Guide 5.2.5.3 “show” P/N 1294008-001Rev D2 EM316EDFAv P/N 1294008-001Rev D2EDFA-1 EM316EDFA5.2.6 Port Context Commands and Examples 5.2.6.1 “?” Fiber Driver EM316EDFA User GuideP/N 1294008-001Rev D2 5.2.6.2“list” 5.2.6.3“show” P/N 1294008-001Rev D2 5.2.6.4“port description”Name EDFA-port1 P/N 1294008-001Rev D2 5.2.7 Displaying and Saving System Parametersslot 1.4 type EM316EDFA rev 1 description EDFA-2 P/N 1294008-001Rev D2 5.2.8 Restoring Default Parameters6.1 Technical Specifications Basic Troubleshooting Checklist6.2 Troubleshooting 6 Appendix20415 Nordhoff Street Chatsworth, CA Tel Fax MRV Communications, Inc