MRV Communications EM316EDFA-LPR Serial Console Interface, Fiber Driver EM316EDFA User Guide

Page 19

5.1 Serial Console Interface

Fiber Driver® EM316EDFA User Guide

5.1 Serial Console Interface

After the network management (NM) module is installed, power up the chassis and attach the serial RS-232 cable to the PC or terminal device. Configuring terminal emulation software on the PC is beyond the scope of this document. The components below may be ordered from MRV.

•Adapter (part number 350-0308 REV-B MRG/20028-2)

• Cable (part number 151-3028 REV-F AI 04/04)

The NM has at least one Ethernet port, which is typically used to connect to a Local Area Network (LAN). The factory default IP address is 192.168.14.201 with netmask 255.255.255.0, sometimes written as 192.168.14.201/24 to show the 24 bits masked for subnetting. The default gateway address is 192.168.14.1/24.

From the network, connect to the NM IP address using telnet or SSH (secure shell) to open the command line interface (CLI). Telnet services are disabled by default on the EM316LNXNM-OT, but they may be enabled for additional CLI access.

Each NM has an RS-232 interface that is used for serial communications to the CLI. This connection is recommended for network setup. Besides configuration simplicity, it offers the advantage of “out-of-band” management for greater network autonomy.

Configure the EM316LNXNM-OT RS-232 serial parameters with the following values.

	•	• 38400 baud
RS-232	•	• 8 data bits
Serial Port	•	• 1 stop bit
Parameters	•	• no parity

• • no flow control

P/N 1294008-001 Rev D2

10

Image 19

Contents Erbium Doped Fiber Inline Pre-Amplifier EM316EDFA-BREM316EDFA-LPR Erbium Doped Fiber Amplifier Booster5 Module Management 3 Preparation and InstallationTable of Contents 2 Introduction to EM316EDFA Optical AmplifiersTable of Figures 6 Appendix1.3 Customer Support 1 Preliminary Considerations1.1 Trademarks 1.2 CopyrightFiber Driver Modules 1.4 ComplianceFiber Driver EM316EDFA User Guide Fiber Driver Chassis1.5.2 Laser Safety 1.5General Safety1.5.1Cautions and Warnings Fiber Driver EM316EDFA User Guide 1.5.3 Laser Device Classifications1.5.5 Workplace Preparation 1.5.4 Static ElectricityDocument Number 1.6 About This Manual1.7 Latest Revision and Related Documents Fiber Driver EM316EDFA User GuideFiber Driver EM316EDFA User Guide 2 Introduction to EM316EDFA Optical AmplifiersC-band pre-amplifier 2.1.3EDFA Alarm Outputs 2.1 Features2.1.2EDFA Control Inputs 3.1 Unpacking the Fiber Driver Module 3 Preparation and Installation3.2 Front Panel 3.4 DIP Switches3.3 LEDs 3.5.1.1.1Tools 3.5 Module Installation3.5.1.1.2Procedure Fiber Driver EM316EDFA User GuideP/N 1294008-001Rev D2 4.1 Network Management Control and Monitoring 4 EDFA Features4.1.1 Management Control from the Network 4.1.2 EM316EDFA Alarm Output Pins4.1.3 Operating Parameters 5 Module Management Serial Port 5.1 Serial Console InterfaceFiber Driver EM316EDFA User Guide RS-2325.2 EM316LNXNM-OTCommand Line Interface CLI P/N 1294008-001Rev D2 5.2.1 EM316LNXNM-OTBoot and CLI Login5.2.2 CLI Navigation 5.2.3.1“show version” 5.2.3 Login Context Commands and Examples5.2.3.2“show log” fiberdriver# show running-config 5.2.3.3“show running-config”P/N 1294008-001Rev D2 fiberdriver# show startup-config 5.2.3.4“show startup-config”P/N 1294008-001Rev D2 Fiber Driver EM316EDFA User Guide 5.2.3.5 Configuring System Parameters5.2.4.1“show” 5.2.4 Chassis ContextFiber Driver EM316EDFA User Guide 5.2.4.2 Other CommandsP/N 1294008-001Rev D2 Description 5.2.5 Slot Context Commands and ExamplesCommand Fiber Driver EM316EDFA User GuideFiber Driver EM316EDFA User Guide 5.2.5.1 “?” 5.2.5.2“list” Fiber Driver EM316EDFA User Guide 5.2.5.3 “show” P/N 1294008-001Rev D2 EM316EDFA P/N 1294008-001Rev D2EM316EDFAv EDFA-15.2.6 Port Context Commands and Examples 5.2.6.1 “?” Fiber Driver EM316EDFA User GuideP/N 1294008-001Rev D2 5.2.6.2“list” 5.2.6.3“show” P/N 1294008-001Rev D2 5.2.6.4“port description”Name EDFA-port1 P/N 1294008-001Rev D2 5.2.7 Displaying and Saving System Parametersslot 1.4 type EM316EDFA rev 1 description EDFA-2 P/N 1294008-001Rev D2 5.2.8 Restoring Default Parameters6 Appendix Basic Troubleshooting Checklist6.1 Technical Specifications 6.2 Troubleshooting20415 Nordhoff Street Chatsworth, CA Tel Fax MRV Communications, Inc