DigiTech GSP1101 owner manual Rear Panel

Page 12

Rear Panel

Rear Panel

1

2

3

4

5

6

7

8

9

10

11

12 13

1.Power Jack.

Attach the included power cord here.

2.USB

The USB jack connects the GSP1101 to a computer and serves two purposes. First, it lets the GSP1101 communicate with the X-Edit Editor/Librarian software. Second, it is used to stream four channels of audio (2 up/2 back) to and from the computer when using the GSP1101 with recording software. USB drivers must be installed prior to using the USB port.These can be found on the included CD.

3.Footswitch

This 1/4” jack connects the optional FS300 3-button footswitch. Functions include preset up, preset down, and bypass.

4.Expression

Connect any passive volume pedal here to control nearly any of the GSP1101 effects in real time. See page 40 for more information about assigning parameters to the Expression Pedal.

5.Configuration Port

This RJ45 jack is reserved for future use. Do not connect to an Eth ernet port.

The connected device will be damaged.

6.MIDI In

Connects to MIDI devices, letting them control the GSP1101. The GSP1101 responds to MIDI program changes and CC messages. See page 48 for more information about MIDI.

7.MIDI Thru

Passes on MIDI signals from the MIDI In jack to MIDI devices downstream. Can also be used for allowing the GSP1101 to transmit MIDI program changes to another device (See page 48 for more information about MIDI.)

GSP1101 Owner’s Manual



Image 12
Contents GSP1101 Guitar Preamp/ Processor Important Safety Instructions Electromagnetic Compatibility Warranty Contents Page Make Connections Basic Setup Select a PresetIntroduction Quick StartEdit and Store a Preset To Edit a PresetTo Store/Copy a Preset Quick Edit Screen To use the Quick Edit screenFront Panel Tuner / Setup Wizard PowerTone Library Effects LibraryRear Panel Ground Lift Switch Mixer Outputs XLRLine Outputs Loop Left Mono Return / Right ReturnUsing the GSP1101 GSP1101 BasicsSetup Wizard Connect your guitar to the Input on the GSP1101 front panel Connect the amp’s Loop Send to GSP1101’s Loop Return To use the Setup Wizard Preset Screen Amp Model Effects highlighted are activeSelecting a Preset Editing a Preset Tone and Effect LibrariesTo Select a new Tone Library Setting Rotary Editing a Preset Individual Parameters To Store and Rename a PresetEditing Expression Links More About Editing Presets ArrowsLFO Settings Preset LevelTo change the level of a preset Seamless TimeMain Menu Screen Factory Reset VersionContrast Edit Effects/Preset screen WAH CompressorDistortion Distortion On/OffDistortion Model Parameters Preamp / CABAmp On/Off Master Volume Amp ModelCab Model Amp GainBass MidrangeParametric EQ FX Loop / Preamp Loop GateThreshold Noise Gate only Sensitivity Auto Swell onlyCHORUS/FX FX On/OffPosition Chorus Model ParametersPhaser Model Parameters Flanger Model ParametersSpeed DepthIntensity DopplerVolume Chorus/VibratoWaveform DigiTech Tremolo and Panner only SensitivityPedal VoxBalance Blend Shift AmountPedal Position MixLevel Key ScaleOctave Dry LevelDelay Delay Model ParametersReverb Reverb Model ParametersExpression Links To set up Seamless Time Seamless TimeLFO Settings To set up the LFOsPreset Level Setup Line Output SetupGlobal Functions Guitar TunerTo configure the 1/4 Line Outputs Cabinet to AmpXLR Out Level To change the XLR Out LevelType of Loop USB Setup Global CabinetTo change the Global Cabinet option Global EQ Contrast VersionMidi Menu Preset Map To set up the Global Controller mappingTo map Midi program change numbers CC/Controller MapPreset Load Merge In ThruSend Midi Prgms Midi TempoFactory Reset To do a Factory ResetSpecifications General SpecificationsAnalog Input Connections Analog Output ConnectionsFootswitch Input Power RequirementsPower Consumption Unit DimensionsMidi Implementation Table Function Transmitted Recognized RemarksBlock Diagram USBPreset List DC/AC