DigiTech GSP1101 owner manual Important Safety Instructions

Page 2

IMPORTANT SAFETY INSTRUCTIONS

The symbols shown above are internationally accepted sym- bols that warn of potential hazards with electrical products. The lightning flash with arrowpoint in an equilateral triangle means that there are dangerous voltages present within the unit. The exclamation point in an equilateral triangle indicates that it is necessary for the user to refer to the owner’s manual.

These symbols warn that there are no user serviceable parts inside the unit. Do not open the unit. Do not attempt to service the unit yourself. Refer all servicing to qualified personnel. Opening the chassis for any reason will void the manufacturer’s warranty. Do not get the unit wet. If liquid is spilled on the unit, shut it off immediately and take it to a dealer for service. Disconnect the unit during storms to prevent damage.

Safety Instructions

Notice For Customers If Your Unit Is Equipped With A Power Cord.

WARNING: THIS APPLIANCE SHALL BE CONNECTED TO A MAINS SOCKET OUTLET WITH A PROTECTIVE EARTHING CONNECTION.

The cores in the mains lead are coloured in accordance with the following code:

GREEN and YELLOW - Earth

BLUE - Neutral

BROWN - Live

As colours of the cores in the mains lead of this appliance may not cor- respond with the coloured markings identifying the terminals in your plug, proceed as follows:

The core which is coloured green and yellow must be connected to the terminal in the plug marked with the letter E, or with the earth symbol, or coloured green, or green and yellow.

The core which is coloured blue must be connected to the terminal marked N or coloured black.

The core which is coloured brown must be connected to the terminal marked L or coloured red.

This equipment may require the use of a different line cord, attachment plug, or both, depending on the available power source at installation. If the attachment plug needs to be changed, refer servicing to qualified service personnel who should refer to the table below. The green/yellow wire shall be connected directly to the units chassis.

CONDUCTOR

WIRE COLOR

 

 

Normal

Alt

L

LIVE

BROWN

BLACK

N

NEUTRAL

BLUE

WHITE

E

EARTH GND

GREEN/

GREEN

YEL

 

 

 

WARNING: If the ground is defeated, certain fault conditions in the unit or in the system to which it is connected can result in full line voltage between chassis and earth ground. Severe injury or death can then result if the chas- sis and earth ground are touched simultaneously.

WARNING FOR YOUR PROTECTION

PLEASE READ THE FOLLOWING:

KEEP THESE INSTRUCTIONS

HEED ALL WARNINGS

FOLLOW ALL INSTRUCTIONS

The apparatus shall not be exposed to dripping or splashing liquid and no object filled with liquid, such as vases, shall be placed on the apparatus

CLEAN ONLY WITH A DRY CLOTH.

DO NOT BLOCK ANY OF THE VENTILATION OPENINGS. INSTALL IN ACCORDANCE WITH THE MANUFACTURER’S INSTRUCTIONS.

DO NOT INSTALL NEAR ANY HEAT SOURCES SUCH AS RADIATORS, HEAT REGISTERS, STOVES, OR OTHER APPARATUS (INCLUDING AMPLIFIERS) THAT PRODUCE HEAT.

ONLY USE ATTACHMENTS/ACCESSORIES SPECIFIED BY THE MANUFACTURER.

UNPLUG THIS APPARATUS DURING LIGHTNING STORMS OR WHEN UNUSED FOR LONG PERIODS OF TIME.

Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or third prong are provided for your safety. If the provided plug does not fit your outlet, consult an electrician for replacement of the obsolete outlet.

Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

Use only with the cart stand, tripod bracket, or table specified by the manu- facture, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

Refer all servicing to to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

POWER ON/OFF SWITCH: For products provided with a power switch, the power switch DOES NOT break the connection from the mains.

MAINS DISCONNECT: The plug shall remain readily operable. For rack-mount or installation where plug is not accessible, an all-pole mains switch with a contact separation of at least 3 mm in each pole shall be incorporated into the electrical installation of the rack or building.

FOR UNITS EQUIPPED WITH EXTERNALLY ACCESSIBLE FUSE RECEPTACLE: Replace fuse with same type and rating only.

MULTIPLE-INPUT VOLTAGE: This equipment may require the use of a differ- ent line cord, attachment plug, or both, depending on the available power source at installation. Connect this equipment only to the power source indicated on the equipment rear panel. To reduce the risk of fire or electric shock, refer servicing to qualified service personnel or equivalent.

Image 2
Contents GSP1101 Guitar Preamp/ Processor Important Safety Instructions Electromagnetic Compatibility Warranty Contents Page Introduction Make Connections Basic SetupSelect a Preset Quick StartTo Store/Copy a Preset Edit and Store a PresetTo Edit a Preset Quick Edit Screen To use the Quick Edit screenFront Panel Tone Library Tuner / Setup WizardPower Effects LibraryRear Panel Line Outputs Ground Lift SwitchMixer Outputs XLR Loop Left Mono Return / Right ReturnUsing the GSP1101 GSP1101 BasicsSetup Wizard Connect your guitar to the Input on the GSP1101 front panel Connect the amp’s Loop Send to GSP1101’s Loop Return To use the Setup Wizard Preset Screen Amp Model Effects highlighted are activeTo Select a new Tone Library Setting Selecting a PresetEditing a Preset Tone and Effect Libraries Rotary Editing a Preset Individual Parameters To Store and Rename a PresetEditing Expression Links More About Editing Presets ArrowsTo change the level of a preset LFO SettingsPreset Level Seamless TimeMain Menu Screen Contrast Factory ResetVersion Edit Effects/Preset screen WAH CompressorDistortion Distortion On/OffAmp On/Off Distortion Model ParametersPreamp / CAB Master Volume Amp ModelBass Cab ModelAmp Gain MidrangeParametric EQ Threshold Noise Gate only FX Loop / Preamp LoopGate Sensitivity Auto Swell onlyPosition CHORUS/FXFX On/Off Chorus Model ParametersPhaser Model Parameters Flanger Model ParametersIntensity SpeedDepth DopplerWaveform DigiTech Tremolo and Panner only VolumeChorus/Vibrato SensitivityBalance PedalVox Pedal Position BlendShift Amount MixLevel Octave KeyScale Dry LevelDelay Delay Model ParametersReverb Reverb Model ParametersExpression Links To set up Seamless Time Seamless TimePreset Level LFO SettingsTo set up the LFOs Global Functions SetupLine Output Setup Guitar TunerXLR Out Level To configure the 1/4 Line OutputsCabinet to Amp To change the XLR Out LevelType of Loop To change the Global Cabinet option USB SetupGlobal Cabinet Global EQ Midi Menu ContrastVersion To map Midi program change numbers Preset MapTo set up the Global Controller mapping CC/Controller MapSend Midi Prgms Preset LoadMerge In Thru Midi TempoFactory Reset To do a Factory ResetAnalog Input Connections SpecificationsGeneral Specifications Analog Output ConnectionsPower Consumption Footswitch InputPower Requirements Unit DimensionsMidi Implementation Table Function Transmitted Recognized RemarksBlock Diagram USBPreset List DC/AC