DigiTech GSP1101 owner manual Speed, Depth, Intensity, Doppler, Crossover, Vibrato/Pan, Waveform

Page 38

The Edit Effects/Preset Screen

VIBRATO

The DigiTech Vibrato effect modulates the pitch of the incoming signal at an even rate.

Parameters include:

Speed

Adjusts the rate (Speed) at which the pitch modulates. Ranges from 0 to 99.

Depth

Adjusts the intensity (Depth) of the modulating pitch. Ranges from 0 to 99.

Rotary Speaker

The Rotary Speaker emulates a device that included a spinning horn and woofer. The rotation of these two speakers produced an interesting combination of the sound panning from side to side. This produced a slight pitch change due to the speed of the sound coming towards, and then going away from the listener. Parameters include:

Speed

Adjusts the rate (Speed) of the spinning speakers. Ranges from 0 to 99.

Intensity

Controls the intensity of the effect. Ranges from 0 to 99.

Doppler

Controls the Pitch Shift effect that is the ratio between the horn and the rotor posi- tions. Ranges from 0 to 99.

Crossover

Selects the crossover frequency between the horn and rotor. Ranges from 0 (200 Hz) to 99 (1600 Hz).

VibroPan

A vibrato is an effect that modulates the pitch of the incoming signal.This takes the whole signal slightly in and out of tune at a steady pace. The DigiTech® VibroPan also incorpo- rates an automatic panner with the vibrato effect that creates a lush chorus-like sound. Parameters include:

Speed

Adjusts how fast the signal is being modulated.

Depth

Adjusts the amount of pitch change.

Vibrato/Pan

Adjusts the amount of panning incorporated with the vibrato effect.When set at 0, this effect is a standard vibrato. As the parameter is turned up, the phase difference of the vibrato signal sent to the two channels is changed until a full stereo image is obtained at 99.

Waveform

Selects a waveform:Triangle, Sine, or Square.


GSP1101 Owner’s Manual	32

Image 38

Contents GSP1101 Guitar Preamp/ Processor Important Safety Instructions Electromagnetic Compatibility Warranty Contents Page Introduction Make Connections Basic SetupSelect a Preset Quick StartTo Store/Copy a Preset Edit and Store a PresetTo Edit a Preset Quick Edit Screen To use the Quick Edit screenFront Panel Tone Library Tuner / Setup WizardPower Effects LibraryRear Panel Line Outputs Ground Lift SwitchMixer Outputs XLR Loop Left Mono Return / Right ReturnUsing the GSP1101 GSP1101 BasicsSetup Wizard Connect your guitar to the Input on the GSP1101 front panel Connect the amp’s Loop Send to GSP1101’s Loop Return To use the Setup Wizard Preset Screen Amp Model Effects highlighted are activeTo Select a new Tone Library Setting Selecting a PresetEditing a Preset Tone and Effect Libraries Rotary Editing a Preset Individual Parameters To Store and Rename a PresetEditing Expression Links More About Editing Presets ArrowsTo change the level of a preset LFO SettingsPreset Level Seamless TimeMain Menu Screen Contrast Factory ResetVersion Edit Effects/Preset screen WAH CompressorDistortion Distortion On/OffAmp On/Off Distortion Model ParametersPreamp / CAB Master Volume Amp ModelBass Cab ModelAmp Gain MidrangeParametric EQ Threshold Noise Gate only FX Loop / Preamp LoopGate Sensitivity Auto Swell onlyPosition CHORUS/FXFX On/Off Chorus Model ParametersPhaser Model Parameters Flanger Model ParametersIntensity SpeedDepth DopplerWaveform DigiTech Tremolo and Panner only VolumeChorus/Vibrato SensitivityBalance PedalVox Pedal Position BlendShift Amount MixLevel Octave KeyScale Dry LevelDelay Delay Model ParametersReverb Reverb Model ParametersExpression Links To set up Seamless Time Seamless TimePreset Level LFO SettingsTo set up the LFOs Global Functions SetupLine Output Setup Guitar TunerXLR Out Level To configure the 1/4 Line OutputsCabinet to Amp To change the XLR Out LevelType of Loop To change the Global Cabinet option USB SetupGlobal Cabinet Global EQ Midi Menu ContrastVersion To map Midi program change numbers Preset MapTo set up the Global Controller mapping CC/Controller MapSend Midi Prgms Preset LoadMerge In Thru Midi TempoFactory Reset To do a Factory ResetAnalog Input Connections SpecificationsGeneral Specifications Analog Output ConnectionsPower Consumption Footswitch InputPower Requirements Unit DimensionsMidi Implementation Table Function Transmitted Recognized RemarksBlock Diagram USBPreset List DC/AC