JVC GR DVL 200 specifications 10 EN, Loading/Unloading a Cassette

Page 10

10 EN

Erase protection tab*

Make sure the window side is facing out.

Cassette holder

OPEN/EJECT Switch

 

 

 

 

 

 

 

 

 

 

Cassette holder cover

PUSH HERE

*To Protect Valuable Recordings . . .

.... slide the erase protection tab on the back of

the tape in the direction of “SAVE”. This prevents the tape from being recorded over. To record on this tape, slide the tab back to “REC” before loading it.

GETTING STARTED (cont.)

Loading/Unloading A Cassette

The camcorder needs to be powered up to load or eject a cassette.

1 Slide and hold OPEN/EJECT in the direction of the arrow then pull the cassette holder cover open until it locks. The cassette holder opens automatically.

•Do not touch internal components.

2 Insert or remove a tape and press “PUSH HERE” to close the cassette holder.

•Once the cassette holder is closed, it recedes automatically. Wait until it recedes completely before closing the cassette holder cover.

•When the battery’s charge is low, you may not be able to close the cassette holder cover. Do not apply force. Replace the battery with a fully charged one before continuing.

3 Close the cassette holder cover firmly until it locks into place.

Approximate recording time

Tape

Recording mode

 

 

 

SP

LP

 

 

 

30 min.

30 min.

45 min.

 

 

 

60 min.

60 min.

90 min.

 

 

 

80 min.

80 min.

120 min.

 

 

 

NOTES:

●It takes a few seconds for the cassette holder to open. Do not apply force.

●If you wait a few seconds and the cassette holder does not open, close the cassette holder cover and try again. If the cassette holder still does not open, turn the camcorder off then on again.

●If the tape does not load properly, open the cassette holder cover fully and remove the cassette. A few minutes later, insert it again.

●When the camcorder is suddenly moved from a cold place to a warm environment, wait a short time before opening the cassette holder cover.

●Closing the cassette holder cover before the cassette holder comes out may cause damage to the camcorder.

●Even when the camcorder is switched off, a cassette can be loaded or unloaded. After the cassette holder is closed with the camcorder switched off, however, it may not recede. It is recommended to turn the power on before loading or unloading.

●When resuming recording, once you open the cassette holder cover a blank portion will be recorded on the tape or a previously recorded scene will be erased (recorded over) regardless of whether the cassette holder came out or not. See page 19 for information about recording from the middle of a tape.

●Loosen the Grip Strap if it appears to interfere with the cassette holder cover operation (  pg. 8).

Page 9 Page 11
Image 10
Page 9 Page 11
Contents GR-DVL200 Dear Customer It is recommended that youEN3 Above ALLCD-ROM GR-DVL200EG Owners How To Attach The Core Filter Release the stoppers on both ends of the Core FilterLithium-ion is vulnerable in colder temperatures PowerCharging the Battery Pack About BatteriesTo Detach The Battery Pack Using the Battery PackUsing AC Power InformationShoulder Strap Attachment Grip AdjustmentViewfinder Adjustment Tripod MountingDate/Time Settings Press MENU/BRIGHT. The Menu Screen appears10 EN Loading/Unloading a CassetteSet the tape recording mode depending on your preference Recording Mode SettingEN11 Picture Quality Mode Setting 12 ENOFF Operation ModeEN13 VideoWhile recording is in progress To Adjust The Brightness Of The Display14 EN To Stop RecordingJournalistic Shooting EN15SELF-RECORDING Motor Drive Mode Power Switch Snapshot For Video RecordingSnapshot Mode Selection 16 ENImage is stored in the camcorder’s built-in memory Basic Shooting SnapshotAvailable Snapshot modes are the same as those on pg To Delete Unwanted Still ImagesZoom Slide the Power Zoom Lever towards T18 EN Zoom OutEN19 When a blank portion is recorded on a tapeProper recording 20 EN Feature Video LightTo brighten the scene when natural lighting is too dim Set Light OFF/AUTO/ON as requiredEN21 Feature Auto FocusFeature Manual Focus To obtain correct focusSee pg Using Menus For Detailed AdjustmentAppears Go to stepMenu Screen Explanations EN23 Menu Screen Explanations EN25 Select OFF in step Fade/Wipe EffectsTo Deactivate The Selected Effect If you select Picture Wipe/Dissolve during recordingEN27 Fader And Wipe MenuTo Deactivate The Selected Mode Programme AE With Special EffectsIris Lock Exposure ControlEN29 To Return To Automatic White Balance White Balance AdjustmentManual White Balance Operation To Change The Tint For RecordingEN31 To Control The Speaker VolumeAvailable only with the remote control provided  pg Playback Zoom and Playback Special EffectsUsing Menus For Detailed Adjustment Display Playback SoundEN33 34 EN Normal PlaybackIndex Playback Index ScreenEN35 Slide Show 36 ENAfter , press 4/6. To stop the Slide Show, press To Protect AN Image Protecting ImagesEN37 To Remove Protection38 EN To Delete ALL ImagesEN39 Initialising The Built-in MemoryYou can initialise the camcorder’s built-in memory anytime 40 EN If using a VCR . . . go to step If not . . . go to step EN4142 EN Connection To a Personal ComputerEN43 Connection To a Video Unit Equipped With a DV ConnectorMake sure all units are turned off Dubbing To a VCR 44 ENVCR Recording deck EN45 46 EN Indicator disappears when dubbing is completeMemory To a Tape Dubbing Images Recorded On a Tape To The Built-in Memory EN47Installing The Batteries 48 ENEN49 FF ButtonFeature Playback Zoom Feature Slow-Motion PlaybackFeature Frame-By-Frame Playback 50 ENFeature Playback Special Effects EN51Random Assemble Editing R.A.Edit VCR Code List52 EN SET REMOTE/VCR CodeMake Connections JVC VCR equipped with a remote pause connectorEN53 VCR other than above54 EN Select ScenesEN55 Automatic Editing to VCRDiagnosing VCR/CAMCORDER Timing 56 ENFor More Accurate Editing Recording deckAdjustment of VCR/CAMCORDER Timing EN57Audio Dubbing Set 12BIT Mode to Sound 2 or MIX Menu Screen  pg58 EN To hear the dubbed sound during playbackBright Clean the lens and checkCorrective Action Dark place, or the contrast Focus again  pg Was lowTroubleshooting 60 ENEN61 62 EN EN63 Or channel appropriate Video mode For video playbackBlink 64 EN Turn off the camcorder After Use Cleaning The CamcorderPress Battery Release and remove the battery pack Press Push Here to close the cassette holder66 EN 345 6 7 # $ %EN67 68 EN EN69 Appears when Digital Image Stabiliser DIS is engagedAutomatically adjusted Approximate zoom ratio Appears during ZoomingLCD Monitor/Viewfinder Indications During D.S.C. Playback 1Displays the sound modeLCD Monitor/Viewfinder Indications During Video Playback 5Displays the time codeEN71 FunctionUnit in Safeguard DUB ErrorCheck TAPE’S Erase Protection Switch Mode RemoveEN73 To prevent damage and prolong service lifeTo avoid hazards 74 EN About moisture condensation EN75Serious malfunctioning Icons  pg 76 ENDate/Time Display  pg , 32 LCD monitor/Viewfinder  pg IndicationsEN77 Time Code  pg , 25, 32For Digital Video Camera 78 ENFor General For Digital Still CameraFor Connectors EN79GR-DVL200
Top Page Image Contents