JVC GR DVL 200 specifications Corrective Action, Bright, Clean the lens and check

Page 59

TROUBLESHOOTING

EN59

If, after following the steps in the chart below, the problem still exists, please consult your nearest JVC dealer.

The camcorder is a microcomputer-controlled device. External noise and interference (from a TV, a radio, etc.) might prevent it from functioning properly. In such cases, first disconnect its power supply unit (battery pack, AC Power Adapter/Battery Charger, etc.) and wait a few minutes; and then re-connect it and proceed as usual from the beginning.

	SYMPTOM			POSSIBLE CAUSES			CORRECTIVE ACTION
1.	No power is supplied.		1. • The power is not connected				1. • Connect the AC Power
			properly.				Adapter/Charger securely
			• The battery is dead.				( pg. 7).
							• Replace the dead battery
							with a fully charged one
							( pg. 6, 7).

2.	“SET DATE/TIME!”		2. • The date/time is not set.				2. • Set the date/time ( pg. 9).
	appears.		• The built-in clock battery				• Consult your nearest JVC
			has run out and the				dealer for replacement.
			previously set date/time has
			been erased.

3.	Recording cannot be		3. — For Video Recording —				3. • Set the tape’s erase
	performed.		• The tape’s erase protection				protection tab to “REC”
			tab is set to “SAVE”.				( pg. 10).
			• The Power Switch is set to				• Set the Power Switch to
			“	” or “OFF”.			“	” or “ ” ( pg. 13).
			• The VIDEO/DSC Switch is				• Set the VIDEO/DSC Switch
			set to “		”.		to “VIDEO”.
			•“TAPE END” appears.				• Replace with new cassette
			• The cassette holder cover is				( pg. 10).
			open.				• Close the cassette holder
			— For D.S.C. Recording —				cover.
			• The VIDEO/DSC Switch is				• Set the VIDEO/DSC Switch
			set to “VIDEO”.				to “	”.
			• The camcorder’s built-in				•Delete unwanted still
			memory is full.				images ( pg. 38).

4.	There is no picture.		4. • The camcorder is not getting				4. • Turn the camcorder’s power
			power, or some other				off and on again ( pg. 13).
			malfunction exists.

5. Some functions are not			5. • The Power Switch is set to				5. • Set the Power Switch to
	available using MENU/		“	”.			“	” ( pg. 13).
	BRIGHT.

6. The focus does not adjust			6. • Focus is set to the Manual				6. • Set Focus to the Auto mode
	automatically.		mode.				( pg. 21).
			• The recording was done in a				• Clean the lens and check
			dark place, or the contrast				the focus again ( pg. 65).
			was low.

•The lens is dirty or covered with condensation.

CONTINUED ON NEXT PAGE

Image 59

Contents GR-DVL200 It is recommended that you Dear CustomerAbove ALL EN3CD-ROM Release the stoppers on both ends of the Core Filter GR-DVL200EG Owners How To Attach The Core FilterAbout Batteries PowerCharging the Battery Pack Lithium-ion is vulnerable in colder temperaturesInformation Using the Battery PackUsing AC Power To Detach The Battery PackTripod Mounting Grip AdjustmentViewfinder Adjustment Shoulder Strap AttachmentPress MENU/BRIGHT. The Menu Screen appears Date/Time SettingsLoading/Unloading a Cassette 10 ENEN11 Recording Mode SettingSet the tape recording mode depending on your preference 12 EN Picture Quality Mode SettingVideo Operation ModeEN13 OFFTo Stop Recording To Adjust The Brightness Of The Display14 EN While recording is in progressSELF-RECORDING EN15Journalistic Shooting 16 EN Power Switch Snapshot For Video RecordingSnapshot Mode Selection Motor Drive ModeTo Delete Unwanted Still Images Basic Shooting SnapshotAvailable Snapshot modes are the same as those on pg Image is stored in the camcorder’s built-in memoryZoom Out Slide the Power Zoom Lever towards T18 EN ZoomProper recording When a blank portion is recorded on a tapeEN19 Set Light OFF/AUTO/ON as required Feature Video LightTo brighten the scene when natural lighting is too dim 20 ENTo obtain correct focus Feature Auto FocusFeature Manual Focus EN21Go to step Using Menus For Detailed AdjustmentAppears See pgMenu Screen Explanations EN23 Menu Screen Explanations EN25 If you select Picture Wipe/Dissolve during recording Fade/Wipe EffectsTo Deactivate The Selected Effect Select OFF in stepFader And Wipe Menu EN27Programme AE With Special Effects To Deactivate The Selected ModeEN29 Exposure ControlIris Lock To Change The Tint For Recording White Balance AdjustmentManual White Balance Operation To Return To Automatic White BalancePlayback Zoom and Playback Special Effects To Control The Speaker VolumeAvailable only with the remote control provided pg EN31Using Menus For Detailed Adjustment EN33 Playback SoundDisplay Normal Playback 34 ENEN35 Index ScreenIndex Playback After , press 4/6. To stop the Slide Show, press 36 ENSlide Show To Remove Protection Protecting ImagesEN37 To Protect AN ImageTo Delete ALL Images 38 ENYou can initialise the camcorder’s built-in memory anytime Initialising The Built-in MemoryEN39 40 EN EN41 If using a VCR . . . go to step If not . . . go to stepConnection To a Personal Computer 42 ENMake sure all units are turned off Connection To a Video Unit Equipped With a DV ConnectorEN43 VCR Recording deck 44 ENDubbing To a VCR EN45 Memory To a Tape Indicator disappears when dubbing is complete46 EN EN47 Dubbing Images Recorded On a Tape To The Built-in Memory48 EN Installing The BatteriesFF Button EN4950 EN Feature Slow-Motion PlaybackFeature Frame-By-Frame Playback Feature Playback ZoomEN51 Feature Playback Special EffectsSET REMOTE/VCR Code VCR Code List52 EN Random Assemble Editing R.A.EditVCR other than above JVC VCR equipped with a remote pause connectorEN53 Make ConnectionsSelect Scenes 54 ENAutomatic Editing to VCR EN55Recording deck 56 ENFor More Accurate Editing Diagnosing VCR/CAMCORDER TimingEN57 Adjustment of VCR/CAMCORDER TimingTo hear the dubbed sound during playback Set 12BIT Mode to Sound 2 or MIX Menu Screen pg58 EN Audio DubbingDark place, or the contrast Focus again pg Was low Clean the lens and checkCorrective Action Bright60 EN TroubleshootingEN61 62 EN Blink Or channel appropriate Video mode For video playbackEN63 64 EN Press Push Here to close the cassette holder After Use Cleaning The CamcorderPress Battery Release and remove the battery pack Turn off the camcorder345 6 7 # $ % 66 ENEN67 68 EN Approximate zoom ratio Appears during Zooming Appears when Digital Image Stabiliser DIS is engagedAutomatically adjusted EN695Displays the time code 1Displays the sound modeLCD Monitor/Viewfinder Indications During Video Playback LCD Monitor/Viewfinder Indications During D.S.C. PlaybackFunction EN71Mode Remove DUB ErrorCheck TAPE’S Erase Protection Switch Unit in SafeguardTo avoid hazards To prevent damage and prolong service lifeEN73 74 EN Serious malfunctioning EN75About moisture condensation LCD monitor/Viewfinder pg Indications 76 ENDate/Time Display pg , 32 Icons pgTime Code pg , 25, 32 EN77For Digital Still Camera 78 ENFor General For Digital Video CameraEN79 For ConnectorsGR-DVL200