JVC GR DVL 200 specifications Power, Charging the Battery Pack, About Batteries

Page 6

6 EN

GETTING STARTED

Power

Battery pack BN-V408U, BN-V416U or BN-V428U

POWER indicator

To AC outlet

AC Power

Adapter/Charger

DC OUT connector

This camcorder’s 2-way power supply system lets you choose the most appropriate source of power. Do not use provided power supply units with other equipment.

CHARGING THE BATTERY PACK

1 Make sure you unplug the camcorder’s DC cord from the AC Power Adapter/Charger. Plug the AC Adapter/ Charger’s power cord into an AC outlet. The POWER indicator lights.

2 Attach the battery pack with the mark aligned with the corresponding marks on the AC Power Adapter/Charger. The CHARGE Indicator begins

CHARGE indicator

Battery pack

Fully charging time

 

 

BN-V408U

approx. 1 hr. 30 min.

 

 

BN-V416U (optional)

approx. 2 hrs.

 

 

BN-V428U (optional)

approx. 3 hrs. 20 min.

 

 

blinking to indicate charging has started.

3 When the CHARGE indicator stops blinking but stays lit, charging is finished. Slide the battery and lift off. Remember to unplug the AC Adapter/Charger’s power cord from the AC outlet.

NOTES:

●If the protective cap is attached to the battery pack, remove it first.

●Perform charging where the temperature is between 10°C and 35°C. 20°C to 25°C is the ideal temperature range for charging. If the environment is too cold, charging may be incomplete.

●Charging times noted above are for a fully discharged battery pack.

●Charging time varies according to the ambient temperature and the status of the battery pack.

●To avoid interference with reception, do not use the AC Power Adapter/Charger near a radio.

●If you connect the camcorder’s DC cord to the adapter during battery charging, power is supplied to the camcorder and charging stops.

●Since the AC Power Adapter/Charger processes electricity internally, it becomes warm during use. Be sure to use it only in well-ventilated areas.

●When charging the battery pack for the first time or after a long storage period, the CHARGE indicator may not light. In this case, remove the battery pack from the AC Power Adapter/Charger, then try charging again.

●If the battery operation time remains extremely short even after having been fully charged, the battery is worn out and needs to be replaced. Please purchase a new one.

Lithium-ion is vulnerable in colder temperatures.

About Batteries

DANGER! Do not attempt to take the batteries apart, or expose them to flame or excessive heat, as it may cause a fire or explosion.

WARNING! Do not allow the battery or its terminals to come in contact with metals, as this can result in a short circuit and possibly start a fire.

The Benefits Of Lithium-Ion Batteries

Lithium-ion battery packs are small but have a large power capacity. However, when one is exposed to cold temperatures (below 10°C), its usage time becomes shorter and it may cease to function. If this happens, place the battery pack in your pocket or other warm, protected place for a short time, then re-attach it to the camcorder. As long as the battery pack itself is not cold, it should not affect performance.

(If you’re using a heating pad, make sure the battery pack does not come in direct contact with it.)

Page 5 Page 7
Image 6
Page 5 Page 7
Contents GR-DVL200 Dear Customer It is recommended that youEN3 Above ALLCD-ROM GR-DVL200EG Owners How To Attach The Core Filter Release the stoppers on both ends of the Core FilterLithium-ion is vulnerable in colder temperatures PowerCharging the Battery Pack About BatteriesTo Detach The Battery Pack Using the Battery PackUsing AC Power InformationShoulder Strap Attachment Grip AdjustmentViewfinder Adjustment Tripod MountingDate/Time Settings Press MENU/BRIGHT. The Menu Screen appears10 EN Loading/Unloading a CassetteRecording Mode Setting Set the tape recording mode depending on your preferenceEN11 Picture Quality Mode Setting 12 ENOFF Operation ModeEN13 VideoWhile recording is in progress To Adjust The Brightness Of The Display14 EN To Stop RecordingEN15 Journalistic ShootingSELF-RECORDING Motor Drive Mode Power Switch Snapshot For Video RecordingSnapshot Mode Selection 16 ENImage is stored in the camcorder’s built-in memory Basic Shooting SnapshotAvailable Snapshot modes are the same as those on pg To Delete Unwanted Still ImagesZoom Slide the Power Zoom Lever towards T18 EN Zoom OutWhen a blank portion is recorded on a tape EN19Proper recording 20 EN Feature Video LightTo brighten the scene when natural lighting is too dim Set Light OFF/AUTO/ON as requiredEN21 Feature Auto FocusFeature Manual Focus To obtain correct focusSee pg Using Menus For Detailed AdjustmentAppears Go to stepMenu Screen Explanations EN23 Menu Screen Explanations EN25 Select OFF in step Fade/Wipe EffectsTo Deactivate The Selected Effect If you select Picture Wipe/Dissolve during recordingEN27 Fader And Wipe MenuTo Deactivate The Selected Mode Programme AE With Special EffectsExposure Control Iris LockEN29 To Return To Automatic White Balance White Balance AdjustmentManual White Balance Operation To Change The Tint For RecordingEN31 To Control The Speaker VolumeAvailable only with the remote control provided  pg Playback Zoom and Playback Special EffectsUsing Menus For Detailed Adjustment Playback Sound DisplayEN33 34 EN Normal PlaybackIndex Screen Index PlaybackEN35 36 EN Slide ShowAfter , press 4/6. To stop the Slide Show, press To Protect AN Image Protecting ImagesEN37 To Remove Protection38 EN To Delete ALL ImagesInitialising The Built-in Memory EN39You can initialise the camcorder’s built-in memory anytime 40 EN If using a VCR . . . go to step If not . . . go to step EN4142 EN Connection To a Personal ComputerConnection To a Video Unit Equipped With a DV Connector EN43Make sure all units are turned off 44 EN Dubbing To a VCRVCR Recording deck EN45 Indicator disappears when dubbing is complete 46 ENMemory To a Tape Dubbing Images Recorded On a Tape To The Built-in Memory EN47Installing The Batteries 48 ENEN49 FF ButtonFeature Playback Zoom Feature Slow-Motion PlaybackFeature Frame-By-Frame Playback 50 ENFeature Playback Special Effects EN51Random Assemble Editing R.A.Edit VCR Code List52 EN SET REMOTE/VCR CodeMake Connections JVC VCR equipped with a remote pause connectorEN53 VCR other than above54 EN Select ScenesEN55 Automatic Editing to VCRDiagnosing VCR/CAMCORDER Timing 56 ENFor More Accurate Editing Recording deckAdjustment of VCR/CAMCORDER Timing EN57Audio Dubbing Set 12BIT Mode to Sound 2 or MIX Menu Screen  pg58 EN To hear the dubbed sound during playbackBright Clean the lens and checkCorrective Action Dark place, or the contrast Focus again  pg Was lowTroubleshooting 60 ENEN61 62 EN Or channel appropriate Video mode For video playback EN63Blink 64 EN Turn off the camcorder After Use Cleaning The CamcorderPress Battery Release and remove the battery pack Press Push Here to close the cassette holder66 EN 345 6 7 # $ %EN67 68 EN EN69 Appears when Digital Image Stabiliser DIS is engagedAutomatically adjusted Approximate zoom ratio Appears during ZoomingLCD Monitor/Viewfinder Indications During D.S.C. Playback 1Displays the sound modeLCD Monitor/Viewfinder Indications During Video Playback 5Displays the time codeEN71 FunctionUnit in Safeguard DUB ErrorCheck TAPE’S Erase Protection Switch Mode RemoveTo prevent damage and prolong service life EN73To avoid hazards 74 EN EN75 About moisture condensationSerious malfunctioning Icons  pg 76 ENDate/Time Display  pg , 32 LCD monitor/Viewfinder  pg IndicationsEN77 Time Code  pg , 25, 32For Digital Video Camera 78 ENFor General For Digital Still CameraFor Connectors EN79GR-DVL200
Top Page Image Contents