JVC GR-DF473, GR-DF573 Displays the battery remaining power, Remaining power level High Exhausted

Page 59

TROUBLESHOOTING EN 59

	Warning Indications
The memory card cannot be removed from	Warning Indications
the camcorder.

HPush in the memory card a few more times. ( pg. 18)

Picture does not appear on the LCD monitor.

●The viewfinder is pulled out and “PRIORITY” is set to “FINDER”.

HPush the viewfinder back in or set “PRIORITY” to “LCD”.( pg. 19, 37, 40)

●The LCD monitor’s brightness setting is too dark. HAdjust the brightness of the LCD monitor.

( pg. 17)

HIf the monitor is tilted upward 180 degrees, open the monitor fully. ( pg. 19)

An error indication (01 – 04 or 06) appears.

●A malfunction of some kind has occurred. In this case the camcorder’s functions become unusable.

H pg. 61.

The remote control does not work.

●“REMOTE” is set to “OFF”.

HSet “REMOTE” to “ON”. (pg. 37, 40)

●The remote control does not point at the remote

sensor.

HPoint at the remote sensor. ( pg. 25)

●The remote control batteries are exhausted.

HReplace the batteries with fresh ones. ( pg. 25)

Displays the battery remaining power.

Remaining power level

High

Exhausted

As the battery power comes close to nil, the battery remaining power indicator blinks. When the battery power is exhausted, power turns off automatically.

Appears when no tape is loaded. ( pg. 17)

CHECK TAPE’S ERASE PROTECTION TAB

Appears when the erase protection tab is set to “SAVE” while the Power Switch is set toA“” or “M” and the VIDEO/MEMORY Switch is set to “VIDEO”.( pg. 15)

USE CLEANING CASSETTE

Appears if dirt is detected on the heads during recording. Use an optional cleaning cassette. ( pg. 63)

CONDENSATION, OPERATION

PAUSED PLEASE WAIT

Appears if condensation occurs. When this indication is displayed, wait more than 1 hour until condensation disappears.

TAPE!

Appears if a tape is not loaded when the Recording Start/Stop Button or SNAPSHOT Button is pressed while the Power Switch is set to “A” or “M” and the VIDEO/MEMORY Switch is set to “VIDEO”.

TAPE END

Appears when the tape ends during recording or playback.

REFERENCES

SET DATE/TIME!

●Appears when the date/time is not set. ( pg. 16)

●The built-in clock battery has run out and the previously set date/time has been erased. Consult your nearest JVC dealer for replacement.

Image 59

Contents pg Digital Still Camera D.S.C. RecordingDear Customer Navigation Function Wipe/Fader EffectsProgram AE with Special Effects Backlight CompensationSafety Precautions Page Contents EN EN Getting Started IndexOther Parts ConnectorsIndicators ControlsSound 12 B I T During D.S.C. Recording OnlyDuring E-Mail Clip Recording IntervalMIC VolumeBR I GHT Before Using This CamcorderDuring D.S.C. Playback Place here during shooting Provided AccessoriesHow To Attach The Lens Cap Audio extension cable provided Stereo microphone Slide the strap guide fully towards the eyeletBuckle Strap guide Open the cover To MIC EyeletConnect the Power Cord to the AC Adapter. AP-V14E/A only PowerHow To Attach The Core Filter Charging The Battery PackMaximum continuous recording time Data Battery SystemUsing The Battery Pack BATT. Release to detach itAbout Batteries Operation ModeUsing AC Power Power-Linked OperationDate/Time Settings Grip AdjustmentViewfinder Adjustment Language SettingsTo protect valuable recordings Brightness Adjustment Of The DisplaySwitch Open the LCD monitor fully. pg Tripod MountingTo protect valuable files available only for SD Memory Card Loading/Unloading a Memory CardClose the card cover LCD Monitor And Viewfinder Basic RecordingTape Remaining Time Self Recording EN Video RecordingZooming Journalistic ShootingDisplay Minutes Seconds Frames Frames = 1 second Video Recording ENTime Code Recording From The Middle Of a TapeStill Playback Normal PlaybackEN Video Playback Shuttle SearchIf using a VCR, go to step Video Playback Biphonic PlaybackVideo Playback EN Playback Using The RemoteControl Right Slow-Motion PlaybackFrame-By-Frame Playback Pause orPlayback Zoom Playback Special Effects Approximate Number of Storable Images EN D.S.C. RecordingBasic Shooting D.S.C. Snapshot Press Snapshot To cancel Interval Shooting modeInterval Shooting C. Recording ENPlayback Zoom Normal Playback Of ImagesPlayback Of Video Clips EN D.S.C. PlaybackFolder Folder name pg Index Playback Of FilesRemoving On-Screen Display Viewing File InformationTo make video clips from real-time camera image EN Additional Features for D.S.CMail Clip Recording FootageDubbing Still Images Recorded On Resetting The File NameTape To a Memory Card Protecting FilesTo Remove Protection Deleting FilesTo Print By Selecting Still Images And Number Of Prints Setting Print Information Dpof SettingInitialising a Memory Card To Reset The Number Of PrintsFor Video and D.S.C. Recording Menus Menus without Sub MenusMenus with Sub Menus WIPE/FADER pg Program AE pg Exposure pg Balance pg5SEC / 15SEC / 30SEC / 60SEC EN Menus for Detailed AdjustmentRecording Menus Wide Melayu pg , Date/Time SettingsOFF Automatic demonstration will not take place OFF Time code is not displayedSound L Playback MenusFine / Standard StereoOFF / on Image SEL. / Tape SEL. / ALL / ReturnOFF / LCD / LCD/TV OFF / Auto / onSecond Recording To take a snapshot in the 5-second recording modeLED Light Live SlowSnapshot For Video Recording EN Features for RecordingMotor Drive Mode Night ScopeManual focus is recommended in situations listed below To reset to Auto FocusManual Focus Exposure ControlBacklight Compensation Iris LockSpot Exposure Control To return to automatic white balance White Balance AdjustmentManual White Balance Adjustment To change the settingTo deactivate the selected effect Wipe Or Fader EffectsProgram AE With Special Effects Sports Navigation FunctionRecording automatically Night Scope pgTo add thumbnail images during video To find scenes on tape using thumbnailPlayback To delete thumbnail imagesBiphonic Recording To use this camcorder as a player Dubbing To Or From a VCRTo use this camcorder as a recorder Cable as shown in the illustration Digital DubbingEditing EN Connect this camcorder to a video unitEN Editing Using USB cableUsing DV cable Using USB cable B Using DV cableUSB is displayed on the LCD monitor Audio DubbingTo hear the dubbed sound during playback Never disconnect the USB cable whileTo end Insert Editing, press START/STOP, then Stop Insert EditingPress START/STOP to begin editing Video and D.S.C. Recording PowerTroubleshooting EN Advanced featuresOther problems EN TroubleshootingRemaining power level High Exhausted Displays the battery remaining powerAppears when the tape ends during recording or playback DUB Error To clean the LCD monitor Cleaning The CamcorderUser Maintenance EN To clean the exteriorCassettes EN CautionsNot Memory CardsLCD Monitor About moisture condensation How To Handle a CD-ROMProblems Dirty heads can cause the followingØ3.5 mm, stereo Specifications ENCamcorderCassette AC AdapterRecording Capacity TermsPage GR-DF573 GR-DF473 Software Installation and PC Connection Guide Limited Liability How to handle a CD-ROM System Requirements For CyberLink DVD SolutionSoftware Installation Windows Page Updating Device Manager Windows 98SE only Installing USB Mass Storage Class driverTo USB connector Connecting the USB cableTo USB connector To DV connector ConnectorDpof SettingStill ClipsCopying Files to the PC Windows Still images When using Windows 98SEClick OK When using Windows 2000/Me/XPConnections Macintosh Viewing the Contents of a Memory Card MacintoshVideo Clips Still images Dpof Setting dataNavigation data Playing Back Files on the PC Macintosh Transfer the still images Overview of Enjoying the Moving or Still Images on the PCVia the USB cable