Power
This camcorder’s
Charging The Battery Pack
POWER/CHARGE
Tabs Notcheslamp
Power switch
Open the cover.
Battery pack
| To DC connector |
| AC Adapter |
BATT. | Power cord |
RELEASE | To AC outlet |
|
1 Set the Power Switch to “OFF”.
2 Align the battery pack’s two notches with the tabs on the camcorder’s battery pack mount.
3 Insert the terminal end a of the battery pack into the battery pack mount.
4 Firmly push the end b of the battery pack until it locks into place.
5 Connect the AC Adapter to the camcorder, then connect the Power Cord to the AC Adapter.
6 Plug the Power Cord into an AC outlet. The POWER/ CHARGE lamp on the camcorder blinks to indicate charging has started.
7 When the POWER/CHARGE lamp goes out, charging is finished. Unplug the Power Cord from the AC outlet. Disconnect the AC Adapter from the camcorder.
To detach the battery pack
While sliding BATT. RELEASE, remove the battery pack.
Battery pack | Charging time |
|
|
Approx. 1 hr. 30 min. | |
|
|
Approx. 3 hr. | |
|
|
* Provided |
|
NOTES:
●It is recommended that only genuine JVC batteries are used in this camcorder. Using generic
●If the protective cap is attached to the battery pack, remove it first.
●During charging, the camcorder cannot be operated.
●Charging is not possible if the wrong type of battery is used.
GETTING STARTED EN 11
● When charging the battery pack for the first time or after a long storage period, the POWER/CHARGE lamp may not light. In this case, remove the battery pack from the camcorder, then try charging again.
● If the battery operation time remains extremely short even after having been fully charged, the battery is worn out and needs to be replaced. Please purchase a new one.
● Since the AC Adapter processes electricity internally, it becomes warm during use. Be sure to use it only in well- ventilated areas.
● Using the optional
power supplied from the AC adapter. In this case, the battery |
| STARTED | ||
Adapter. |
|
|
|
|
● After 5 minutes has elapsed in |
|
| ||
cassette inserted, the camcorder will automatically turn off its |
|
| ||
charge starts if the battery is attached to the camcorder. |
| GETTING | ||
Using The Battery Pack |
|
| ||
|
|
| ||
|
|
|
|
|
Perform steps 2 – 4 in “Charging The Battery Pack”. |
|
| ||
Maximum continuous recording time |
|
| ||
|
|
|
|
|
Battery pack | LCD monitor on | Viewfinder on |
|
|
|
|
|
|
|
1 hr. 10 min. | 1 hr. 30 min. |
|
| |
|
|
|
|
|
2 hr. 25 min. | 3 hr. 00 min. |
|
| |
|
|
|
|
|
* Provided |
|
|
|
|
NOTES:
●Recording time is reduced significantly under the following conditions:
•Zoom or
•The LCD monitor is used repeatedly.
•The playback mode is engaged repeatedly.
•The LED Light is used.
●Before extended use, it is recommended that you prepare enough battery packs to cover 3 times the planned shooting time.
ATTENTION:
Before detaching the power source, make sure that the camcorder’s power is turned off. Failure to do so can result in a camcorder malfunction.
Using AC Power
Connect the AC Adapter to the camcorder, then connect the Power Cord to the AC Adapter as shown in the illustration.
NOTE:
The provided AC Adapter features automatic voltage selection in the AC range from 110 V to 240 V.
About Batteries
DANGER! Do not attempt to take the batteries apart, or expose them to flame or excessive heat, as it may cause a fire or explosion.
WARNING! Do not allow the battery or its terminals to come in contact with metals, as this can result in a short circuit and possibly start a fire.