JVC GR-DX307, GR-DX107, GR-DX317 Audio Dubbing, Insert Editing, Set Narration to on or MIX.
pg

40 EN EDITING

Audio Dubbing

The audio track can be customised only when recorded in the 12-BIT and SP modes. (
pg. 28)

●Use the provided remote control or an optional remote control kit RM-V717KITU.

Stereo Microphone

Speaker

START/

STOP Microphone Connector

PAUSE

REW PLAY

INSERT STOP

A.DUB

1 Play back the tape to locate the point where editing will start, then press PAUSE (9).

2 While holding A. DUB (D) on the remote control, press PAUSE (9). The “9D” and “MIC” indicators appear.

3 Press PLAY (U), then begin “narrating”. Speak into the microphone.

●To pause dubbing, press PAUSE (9).

4 To end Audio Dubbing, press PAUSE (9), then STOP (8).

To hear the dubbed sound during playback

Set “NARRATION” to “ON” or “MIX”. (
pg. 27, 30)

NOTES:

●Sound is not heard from the speaker during Audio Dubbing.

●When editing onto a tape that was recorded at 12-BIT, the old and new soundtracks are recorded separately.

●If you dub onto a blank space on the tape, the sound may be disrupted. Make sure you only edit recorded areas.

●If feedback or howling occurs during TV playback, move the camcorder’s microphone away from the TV, or turn down the TV’s volume.

●If you change from 12-BIT to 16-BIT in mid-recording and then use the tape for Audio Dubbing, it is not effective from the point where 16-BIT recording began.

●During Audio Dubbing, when the tape moves to scenes recorded in the LP mode, scenes recorded in 16-BIT audio or a blank portion, Audio Dubbing stops.

●Audio dubbing is also possible using an optional microphone connected to the MIC connector.

●While an optional microphone is connected, the built-in microphone is disabled.

●To perform Audio Dubbing with a video unit connected to the camcorder’s AV connector, first set “S/AV INPUT” to “A/ V.IN” or “S.IN” in VIDEO Menu. (
pg. 27, 30)

The “AUX” indication appears instead of “MIC”.

Insert Editing

You can record a new scene into a previously recorded tape, replacing a section of the original recording with minimal picture distortion at the in and outpoints. The original audio remains unchanged.

●Use the provided remote control or an optional remote control kit RM-V717KITU.

NOTES:

●Before performing the following steps, make sure that “TIME CODE” is set to “ON”. (
pg. 27, 31)

●Insert Editing is not possible on a tape recorded in the LP mode or on a blank portion of a tape.

1 Play back the tape, locate the Edit-Out point and press PAUSE (9). Confirm the time code at this point. (
pg. 17)

2 Press REW (3) until the Edit-In point is located, then press PAUSE (9).

3 Press and hold INSERT (I) on the remote control, then press PAUSE (9). The “9I” indicator and the Time Code (min.:sec.) appear and the camcorder enters Insert-Pause mode.

4 Press START/STOP to begin editing.

●Confirm the insert at the time code you checked in step 1.

●To pause editing, press START/STOP. Press it again to resume editing.

5 To end Insert Editing, press START/STOP, then STOP (8).

NOTES:

●Program AE with special effects (
pg. 35) can be used to spice up the scenes being edited during Insert Editing.

●During Insert Editing, the date and time information changes.

●If you perform Insert Editing onto a blank space on the tape, the audio and video may be disrupted. Make sure you only edit recorded areas.

●During Insert Editing, when the tape moves to scenes recorded in the LP mode or a blank portion, Insert Editing stops. (
pg. 47)