46 EN TROUBLESHOOTING
Other problems |
|
| |
| The memory card cannot be removed from the | ||
| |||
|
| camcorder. | |
The POWER/CHARGE lamp on the camcorder does |
|
| |
| HPush in the memory card a few more times. ( pg. 14) | ||
not light during charging. |
|
| |
|
| Picture does not appear on the LCD monitor. | |
● Charging is difficult in places subject to extremely high/low | |||
|
| ||
temperatures. |
| ● The viewfinder is pulled out and “PRIORITY” is set to | |
HTo protect the battery, it is recommended to charge it in |
| “FINDER”. | |
places with a temperature of 10°C to 35°C. ( pg. 49) |
| HPush the viewfinder back in or set “PRIORITY” to “LCD”. | |
● The battery pack is not attached firmly. |
| ( pg. 15, 27, 29) | |
HDetach the battery pack once again and |
| ● The LCD monitor’s brightness setting is too dark. | |
( pg. 11) |
| HAdjust the brightness of the LCD monitor. ( pg. 13) | |
|
| HIf the monitor is tilted upward 180 degrees, open the | |
“SET DATE/TIME!” appears. |
| monitor fully. ( pg. 15) | |
● The |
|
| |
| An error indication (E01 – E04 or E06) appears. | ||
discharged. |
| ||
|
| ||
● The previously set date/time is erased. |
| ● A malfunction of some kind has occurred. In this case the | |
HConnect the camcorder to an AC outlet using the AC |
| camcorder’s functions become unusable. | |
Adapter for over 24 hours to charge the clock’s lithium |
| H pg. 48. | |
battery. ( pg. 12) |
|
| |
| The remote control does not work. | ||
| |||
|
| ||
Files stored in the memory card cannot be deleted. |
|
| |
| ● “REMOTE” is set to “OFF”. | ||
● Files stored in the memory card are protected. |
| ||
| HSet “REMOTE” to “ON”. ( pg. 27, 29) | ||
HRemove protection from the files stored in the memory |
| ● The remote control does not point at the remote sensor. | |
card and delete them. ( pg. 25) |
| HPoint at the remote sensor. ( pg. 19) | |
|
| ● The remote control batteries are exhausted. | |
When the image is printed from the printer, a black |
| HReplace the batteries with fresh ones. ( pg. 19) | |
bar appears at the bottom of the screen. |
|
| |
● This is not a malfunction. |
|
| |
HBy recording with “DIS” activated ( pg. 27, 28) this can |
|
| |
be avoided. |
|
|
When the camcorder is connected via the DV connector, the camcorder does not operate.
●The DV cable was plugged/unplugged with power turned on.
HTurn the camcorder’s power off and on again, then operate it.
Images on the LCD monitor appear dark or whitish.
●In places subject to low temperature, images become dark
due to the characteristics of the LCD monitor. This is not a malfunction.
HAdjust the brightness and angle of the LCD monitor. ( pg. 13, 15)
●When the LCD monitor’s fluorescent light reaches the end of its service life, images on the LCD monitor become dark.
HConsult your nearest JVC dealer.
Coloured bright spots appear all over the LCD monitor or the viewfinder.
●The LCD monitor and the viewfinder are made with high- precision technology. However, black spots or bright spots of light (red, green or blue) may appear constantly on the LCD monitor or the viewfinder. These spots are not recorded on the tape. This is not due to any defect of the unit. (Effective dots: more than 99.99 %)
The cassette will not load properly.
●The battery’s charge is low.
HInstall a fully charged battery. ( pg. 11)