JVC GR-DX107, GR-DX307, GR-DX317 EN Video Playback, Shuttle Search Connections To a TV Or VCR

Turn on the camcorder, the VCR and the TV.

18 EN VIDEO PLAYBACK
Shuttle Search	Connections To A TV Or VCR
Allows high-speed search in either direction during video
playback.
1) During playback, press 5 for forward search, or
3 for reverse search.				To AV connector
2) To resume normal playback, press 4/9.	Open the cover.
● During playback, press and hold 5 or 3. The search
	S/AV/Editing cable
continues as long as you hold the button. Once you release					mark
the button, normal playback resumes.		(provided)
● A slight mosaic effect appears on the display during Shuttle
Search. This is not a malfunction.
ATTENTION:
During Shuttle Search, parts of the	1	2	3	4	5
picture may not be clearly visible,
particularly on the left side of the
screen.

Blank Search			“Y/C”/“CVBS”	Cable Adapter*
			Video Out Select
Helps you find where you should start recording in the			Switch
middle of a tape to avoid time code interruption.			To TV or VCR
( pg. 17)
1 Load a cassette. ( pg. 14)				TV
2 Set the VIDEO/MEMORY Switch to “VIDEO”.
3 Set the Power Switch to “PLAY” while pressing down			VCR
the Lock Button located on the switch.
4 Press MENU. The Menu Screen appears.			A Remote plug: Not connected (When not in use, keep
5 Press SET to select “t”. The VIDEO Menu appears.
			the Remote plug in its protective caddy.)
6 Press	or	to select “BLANK SRCH”, and press	B Black to S-VIDEO IN (Connect when your TV/VCR has
SET. The Sub Menu appears.			S-VIDEO IN and A/V input connectors. In this case, it
7 Press	or	to select “EXECUTE”, and press SET.	is not necessary to connect the yellow video cable.)
			C Yellow to VIDEO IN (Connect when your TV/VCR has
● The “BLANK SEARCH” indication appears and the			only A/V input connectors.)
camcorder automatically starts reverse or forward search,
			D Red to AUDIO R IN**
then stops at the spot which is about 3 seconds of tape			E White to AUDIO L IN**
before the beginning of the detected blank portion.
● To cancel Blank Search midway, press 8.			* If your VCR has a SCART connector, use the provided
NOTES:			cable adapter.
			** Not required for watching still images only.

●Before starting Blank Search, if the current position is at a

blank portion, the camcorder searches in the reverse	NOTE:
direction. If the current position is at a recorded portion, the	Set the video out select switch of the cable adapter as
camcorder searches in the forward direction.	required:
● If the beginning or end of the tape is reached during Blank	Y/C: When connecting to a TV or VCR which accepts
Search, the camcorder stops automatically.	Y/C signals and uses an S-Video cable.
● A blank portion which is shorter than 5 seconds of tape	CVBS: When connecting to a TV or VCR which does not
may not be detected.	accept Y/C signals and uses an audio/video cable.
● The detected blank portion may be located between	1 Make sure all units are turned off.
recorded scenes. Before you start recording, make sure
	2 Connect the camcorder to a TV or VCR as shown in
there is no recorded scene after the blank portion.
	the illustration.

If using a VCR, go to step 3. If not, go to step 4.

3 Connect the VCR output to the TV input, referring to your VCR’s instruction manual.

4

5 Set the VCR to its AUX input mode, and set the TV to its VIDEO mode.

6 Start playback on the camcorder. (
pg. 17)